2,539 research outputs found
Experimental characterization of a supercapacitor-based electrical torque-boost system for downsized ICE vehicles
The need to improve fuel economy and reduce the emission of CO2 and other harmful pollution from internal-combustion-engine vehicles has led to engine downsizing. However, downsized turbocharged engines exhibit a relatively low torque capability at low engine speeds. To overcome this problem, an electrical torque boost may be employed while accelerating and changing gear and to facilitate energy recovery during regenerative braking. This paper describes the operational requirements of a supercapacitor-based torque-boost system, outlines the design and sizing of the electrical drive-train components, and presents experimental characterization of a demonstrator system
MTPA control of IPMSM drives based on virtual signal injection considering machine parameter variations
Due to parameter variations with stator currents, the derivatives of machine parameters with respect to current angle or d-axis current are not zero. However, these derivative terms are ignored by most of mathematical model based efficiency optimized control schemes. Therefore, even though the accurate machine parameters are known, these control schemes cannot calculate the accurate efficiency optimized operation points. In this paper, the influence of these derivative terms on maximum torque per ampere (MTPA) control is analyzed and a method to take into account these derivative terms for MTPA operation is proposed based on the recently reported virtual signal injection control (VSIC) method for interior permanent magnet synchronous machine (IPMSM) drives. The proposed control method is demonstrated by both simulations and experiments under various operating conditions on prototype IPMSM drive systems
Influence of electrode distance on heating behaviour associated to radio frequency processing of low moisture foods
Temperature uniformity and heating rate subjected to radio frequency (RF) heating have major impact on the quality of treated low moisture foods. The objective of this paper was to analyse the influence of electrode distance on the heating behaviour of RF on condition that the sample shape, size, and location between the electrodes were defined. Considering peanut butter (PB) and wheat flour (WF) as sample food, a 3D computer simulation model was developed using COMSOL, which was experimentally validated by a RF machine (27.12 MHz, 6 kW). Specifically, the electrode distances were selected as 84, 89, 93, 99 and 89, 93, 98, 103 (mm) for RF heating of PB and WF, respectively. Results showed that the simulated results and experimental data agreed well; the temperature-time histories of the RF heating of PB and WF were approximate straight lines; both the temperature uniformity index and the heating rate decreased with the increase of the electrode distance; the heating rate had a negative logarithmic linear relationship with the electrode distance, which was independent of the types, geometry shapes and sizes of low moisture foods
Full-wave invisibility of active devices at all frequencies
There has recently been considerable interest in the possibility, both
theoretical and practical, of invisibility (or "cloaking") from observation by
electromagnetic (EM) waves. Here, we prove invisibility, with respect to
solutions of the Helmholtz and Maxwell's equations, for several constructions
of cloaking devices. Previous results have either been on the level of ray
tracing [Le,PSS] or at zero frequency [GLU2,GLU3], but recent numerical [CPSSP]
and experimental [SMJCPSS] work has provided evidence for invisibility at
frequency . We give two basic constructions for cloaking a region
contained in a domain from measurements of Cauchy data of waves at \p
\Omega; we pay particular attention to cloaking not just a passive object, but
an active device within , interpreted as a collection of sources and sinks
or an internal current.Comment: Final revision; to appear in Commun. in Math. Physic
Colliding Plane Waves in String Theory
We construct colliding plane wave solutions in higher dimensional gravity
theory with dilaton and higher form flux, which appears naturally in the low
energy theory of string theory. Especially, the role of the junction condition
in constructing the solutions is emphasized. Our results not only include the
previously known CPW solutions, but also provide a wide class of new solutions
that is not known in the literature before. We find that late time curvature
singularity is always developed for the solutions we obtained in this paper.
This supports the generalized version of Tipler's theorem in higher dimensional
supergravity.Comment: latex, 25 pages, 1 figur
Current residual based stator inter-turn fault detection in permanent magnet machines
Inter-turn short circuit fault, also known as turn fault is a common fault in electric machines which can cause severe damages if no prompt detection and mitigation are conducted. This paper proposes a turn fault detection method for permanent magnet machines based on current residual. After the impact of the turn fault is firstly analyzed on a simplified mathematical machine model to assess the fault signature, a finite element (FE) model is developed to obtain healthy machine behavior. The residual between the measured and estimated currents by the model with the same applied voltages contains mainly the fault features. The quality of the fault detection can be improved because the fault signatures are enhanced, and the impact of the current controller bandwidth on fault signature is minimized. The dc components in the negative sequence current residuals are extracted through angular integration and their magnitude is defined as the fault indicator. The robustness of the fault detection against transient states is achieved. The effectiveness of the proposed method is validated on a triple redundant fault tolerant permanent magnet assisted synchronous reluctance machine (PMA SynRM)
Predictors of Therapy-Related Myelodysplasia and Acute Myeloid Leukemia (t-MDS/AML) After Autologous Hematopoietic Cell Transplantation (AHCT) for Hematologic Malignancies
Metamaterial Polarization Converter Analysis: Limits of Performance
In this paper we analyze the theoretical limits of a metamaterial converter
that allows for linear-to- elliptical polarization transformation with any
desired ellipticity and ellipse orientation. We employ the transmission line
approach providing a needed level of the design generalization. Our analysis
reveals that the maximal conversion efficiency for transmission through a
single metamaterial layer is 50%, while the realistic re ection configuration
can give the conversion efficiency up to 90%. We show that a double layer
transmission converter and a single layer with a ground plane can have 100%
polarization conversion efficiency. We tested our conclusions numerically
reaching the designated limits of efficiency using a simple metamaterial
design. Our general analysis provides useful guidelines for the metamaterial
polarization converter design for virtually any frequency range of the
electromagnetic waves.Comment: 10 pages, 11 figures, 2 table
The effects of the bacterial interaction with visible-light responsive titania photocatalyst on the bactericidal performance
Bactericidal activity of traditional titanium dioxide (TiO2) photocatalyst is effective only upon irradiation by ultraviolet light, which restricts the potential applications of TiO2 for use in our living environments. Recently carbon-containing TiO2 was found to be photoactive at visible-light illumination that affords the potential to overcome this problem; although, the bactericidal activity of these photocatalysts is relatively lower than conventional disinfectants. Evidenced from scanning electron microscopy and confocal Raman spectral mapping analysis, we found the interaction with bacteria was significantly enhanced in these anatase/rutile mixed-phase carbon-containing TiO2. Bacteria-killing experiments indicate that a significantly higher proportion of all tested pathogens including Staphylococcus aureus, Shigella flexneri and Acinetobacter baumannii, were eliminated by the new nanoparticle with higher bacterial interaction property. These findings suggest the created materials with high bacterial interaction ability might be a useful strategy to improve the antimicrobial activity of visible-light-activated TiO2
- …