Comparative Analysis of Raman Signal Amplifying Effectiveness of Silver Nanostructures with Different Morphology

To increase the attractiveness of the practical application of molecular sensing methods, the experimental search for the optimal shape of silver nanostructures allowing to increase the Raman cross section by several orders of magnitude is of great interest. This paper presents a detailed study of spatially separated plasmon-active silver nanostructures grown in SiO2/Si template pores with crystallite, dendrite, and “sunflower-like” nanostructures shapes. Nile blue and 2-mercaptobenzothiazole were chosen as the model analytes for comparative evaluation of the Raman signal amplification efficiency using these structures. It was discussed the features of the structures for the enhancement of Raman intensity. Finally, we showed that silver crystals, dendrites, and “sunflower-like” nanostructures in SiO2/Si template could be used as the relevant materials for Raman signal amplification, but with different efficiency

Morphology and Microstructure Evolution of Gold Nanostructures in the Limited Volume Porous Matrices

The modern development of nanotechnology requires the discovery of simple approaches that ensure the controlled formation of functional nanostructures with a predetermined morphology. One of the simplest approaches is the self-assembly of nanostructures. The widespread implementation of self-assembly is limited by the complexity of controlled processes in a large volume where, due to the temperature, ion concentration, and other thermodynamics factors, local changes in diffusion-limited processes may occur, leading to unexpected nanostructure growth. The easiest ways to control the diffusion-limited processes are spatial limitation and localized growth of nanostructures in a porous matrix. In this paper, we propose to apply the method of controlled self-assembly of gold nanostructures in a limited pore volume of a silicon oxide matrix with submicron pore sizes. A detailed study of achieved gold nanostructures' morphology, microstructure, and surface composition at different formation stages is carried out to understand the peculiarities of realized nanostructures. Based on the obtained results, a mechanism for the growth of gold nanostructures in a limited volume, which can be used for the controlled formation of nanostructures with a predetermined geometry and composition, has been proposed. The results observed in the present study can be useful for the design of plasmonic-active surfaces for surface-enhanced Raman spectroscopy-based detection of ultra-low concentration of different chemical or biological analytes, where the size of the localized gold nanostructures is comparable with the spot area of the focused laser beam

Comparison of Synchrotron and Laboratory X-ray Sources in Photoelectron Spectroscopy Experiments for the Study of Nitrogen-Doped Carbon Nanotubes

The chemical composition and stoichiometry of vertically aligned arrays of nitrogen-doped multi-walled carbon nanotubes (N-CNTs) were studied by photoelectron spectroscopy using laboratory and synchrotron X-ray sources. We performed careful deconvolution of high-resolution core-level spectra to quantify pyridine/pyrrole-like defects in N-CNTs, which are a key factor in the efficiency of the piezoelectric response for this material. It is shown that the XPS method makes it possible to estimate the concentration and type of nitrogen incorporation (qualitatively and quantitatively) in the “N-CNT/Mo electrode” system using both synchrotron and laboratory sources. The obtained results allow us to study the effect of the nickel catalytic layer thickness on the concentration of pyridine/pyrrole-like nitrogen and piezoelectric response in the nanotubes

Comparative Analysis of Raman Signal Amplifying Effectiveness of Silver Nanostructures with Different Morphology

To increase the attractiveness of the practical application of molecular sensing methods, the experimental search for the optimal shape of silver nanostructures allowing to increase the Raman cross section by several orders of magnitude is of great interest. This paper presents a detailed study of spatially separated plasmon-active silver nanostructures grown in SiO2/Si template pores with crystallite, dendrite, and “sunflower-like” nanostructures shapes. Nile blue and 2-mercaptobenzothiazole were chosen as the model analytes for comparative evaluation of the Raman signal amplification efficiency using these structures. It was discussed the features of the structures for the enhancement of Raman intensity. Finally, we showed that silver crystals, dendrites, and “sunflower-like” nanostructures in SiO2/Si template could be used as the relevant materials for Raman signal amplification, but with different efficiency

Nanocomposite Co₃O₄-ZnO Thin Films for Photoconductivity Sensors

Thin nanocomposite films based on zinc oxide (ZnO) added with cobalt oxide (Co3O4) were synthesized by solid-phase pyrolysis. According to XRD, the films consist of a ZnO wurtzite phase and a cubic structure of Co3O4 spinel. The crystallite sizes in the films increased from 18 nm to 24 nm with growing annealing temperature and Co3O4 concentration. Optical and X-ray photoelectron spectroscopy data revealed that enhancing the Co3O4 concentration leads to a change in the optical absorption spectrum and the appearance of allowed transitions in the material. Electrophysical measurements showed that Co3O4-ZnO films have a resistivity up to 3 × 104 Ohm∙cm and a semiconductor conductivity close to intrinsic. With advancing the Co3O4 concentration, the mobility of the charge carriers was found to increase by almost four times. The photosensors based on the 10Co-90Zn film exhibited a maximum normalized photoresponse when exposed to radiation with wavelengths of 400 nm and 660 nm. It was found that the same film has a minimum response time of ca. 26.2 ms upon exposure to radiation of 660 nm wavelength. The photosensors based on the 3Co-97Zn film have a minimum response time of ca. 58.3 ms versus the radiation of 400 nm wavelength. Thus, the Co3O4 content was found to be an effective impurity to tune the photosensitivity of radiation sensors based on Co3O4-ZnO films in the wavelength range of 400–660 nm

High Gas Sensitivity to Nitrogen Dioxide of Nanocomposite ZnO-SnO2 Films Activated by a Surface Electric Field

Gas sensors based on the multi-sensor platform MSP 632, with thin nanocomposite films based on tin dioxide with a low content of zinc oxide (0.5–5 mol.%), were synthesized using a solid-phase low-temperature pyrolysis technique. The resulting gas-sensitive ZnO-SnO2 films were comprehensively studied by atomic force microscopy, Kelvin probe force microscopy, X-ray diffraction, scanning electron microscopy, transmission electron microscopy, scanning transmission electron microscopy, energy dispersive X-ray spectrometry, and X-ray photoelectron spectroscopy. The obtained films are up to 200 nm thick and consist of ZnO-SnO2 nanocomposites, with ZnO and SnO2 crystallite sizes of 4–30 nm. Measurements of ZnO-SnO2 films containing 0.5 mol.% ZnO showed the existence of large values of surface potential, up to 1800 mV, leading to the formation of a strong surface electric field with a strength of up to 2 × 107 V/cm. The presence of a strong surface electric field leads to the best gas-sensitive properties: the sensor’s responsivity is between two and nine times higher than that of sensors based on ZnO-SnO2 films of other compositions. A study of characteristics sensitive to NO2 (0.1–50 ppm) showed that gas sensors based on the ZnO-SnO2 film demonstrated a high sensitivity to NO2 with a concentration of 0.1 ppm at an operating temperature of 200 °C

A few-minute synthesis of CsPbBr₃ nanolasers with a high quality factor by spraying at ambient conditions

Inorganic cesium lead halide perovskite nanowires, generating laser emission in the broad spectral range at room temperature and low threshold, have become powerful tools for the cutting-edge applications in the optoelectronics and nanophotonics. However, to achieve high-quality nanowires with the outstanding optical properties, it was necessary to employ long-lasting and costly methods of their synthesis, as well as postsynthetic separation and transfer procedures that are not convenient for large-scale production. Here we report a novel approach to fabricate high-quality CsPbBr3 nanolasers obtained by rapid precipitation from dimethyl sulfoxide solution sprayed onto hydrophobic substrates at ambient conditions. The synthesis technique allows producing the well-separated nanowires with a broad size distribution of 2-50 μm in 5-7 min, being the fastest method to the best of our knowledge. The formation of nanowires occurs via ligand-assisted reprecipitation triggered by intermolecular proton transfer from (CH3)2CHOH to H2O in the presence of a minor amount of water. The XRD patterns confirm an orthorhombic crystal structure of the as-grown CsPbBr3 single nanowires. Scanning electron microscopy images reveal their regular shape and truncated pyramidal end facets, while high-resolution transmission electron microscopy ones demonstrate their single-crystal structure. The lifetime of excitonic emission of the nanowires is found to be 7 ns, when the samples are excited with energy below the lasing threshold, manifesting the low concentration of defect states. The measured nanolasers of different lengths exhibit pronounced stimulated emission above 13 μJ cm-2 excitation threshold with quality factor Q = 1017-6166. Their high performance is assumed to be related to their monocrystalline structure, low concentration of defect states, and improved end facet reflectivity.</p