A new gas discharge process for preparation of non-fouling surfaces on biomaterials

A non-fouling surface containing immobilized polyethylene oxide (PEO) was achieved using an argon radio-frequency glow discharge treatment (RFGD) of polyethylene films precoated with Brij hydrocarbon-PEO surfactants. Surface wettability of RFGD-treated and washed surfaces increased the most when PEO surfactants with unsaturated and/or long alkyl tails were used. ESCA measurements of treated and washed surfaces showed increases of surface O/C ratios and ether carbon peaks in high resolution Cls spectra. These results demonstrate the retention of the PEO surfactants on the treated surfaces. Fibrinogen adsorp tion on these treated surfaces was significantly reduced, from 500 to 50 ng/cm2, indicating the non-fouling properties of the RFGD-immobilized PEO surfactants

Immobilization of Polyethylene Oxide Surfactants for Non-Fouling Biomaterial Surfaces Using an Argon Glow Discharge Treatment

A non-fouling (protein-resistant) polymer surface is achieved by the covalent immobilization of polyethylene oxide (PEO) surfactants using an inert gas discharge treatment. Treated surfaces have been characterized using electron spectroscopy for chemical analysis (ESCA), static secondary ion mass spectrometry (SSIMS), water contact angle measurement, fibrinogen adsorption, and platelet adhesion. This paper is intended to review our recent work in using this simple surface modification process to obtain wettable polymer surfaces in general, and non-fouling biomaterial surfaces in particular

Fundamentals of microcrack nucleation mechanics

A foundation for ultrasonic evaluation of microcrack nucleation mechanics is identified in order to establish a basis for correlations between plane strain fracture toughness and ultrasonic factors through the interaction of elastic waves with material microstructures. Since microcracking is the origin of (brittle) fracture, it is appropriate to consider the role of stress waves in the dynamics of microcracking. Therefore, the following topics are discussed: (1) microstress distributions with typical microstructural defects located in the stress field; (2) elastic wave scattering from various idealized defects; and (3) dynamic effective-properties of media with randomly distributed inhomogeneities

Quantum planes and quantum cylinders from Poisson homogeneous spaces

Quantum planes and a new quantum cylinder are obtained as quantization of Poisson homogeneous spaces of two different Poisson structures on classical Euclidean group E(2).Comment: 13 pages, plain Tex, no figure

Polaronic transport induced by competing interfacial magnetic order in a La0.7_{0.7}Ca0.3_{0.3}MnO3_{3}/BiFeO3_{3} heterostructure

Using ultrafast optical spectroscopy, we show that polaronic behavior associated with interfacial antiferromagnetic order is likely the origin of tunable magnetotransport upon switching the ferroelectric polarity in a La$_{0.7}$Ca$_{0.3}$MnO$_{3}$/BiFeO$_{3}$ (LCMO/BFO) heterostructure. This is revealed through the difference in dynamic spectral weight transfer between LCMO and LCMO/BFO at low temperatures, which indicates that transport in LCMO/BFO is polaronic in nature. This polaronic feature in LCMO/BFO decreases in relatively high magnetic fields due to the increased spin alignment, while no discernible change is found in the LCMO film at low temperatures. These results thus shed new light on the intrinsic mechanisms governing magnetoelectric coupling in this heterostructure, potentially offering a new route to enhancing multiferroic functionality

The first products made in space: Monodisperse latex particles

The preparation of large particle size 3 to 30 micrometer monodisperse latexes in space confirmed that original rationale unequivocally. The flight polymerizations formed negligible amounts of coagulum as compared to increasing amounts for the ground-based polymerizations. The number of offsize large particles in the flight latexes was smaller than in the ground-based latexes. The particle size distribution broadened and more larger offsize particles were formed when the polymerizations of the partially converted STS-4 latexes were completed on Earth. Polymerization in space also showed other unanticipated advantages. The flight latexes had narrower particle size distributions than the ground-based latexes. The particles of the flight latexes were more perfect spheres than those of the ground-based latexes. The superior uniformity of the flight latexes was confirmed by the National Bureau of Standards acceptance of the 10 micrometer STS-6 latex and the 30 micrometer STS-11 latexes as Standard Reference Materials, the first products made in space for sale on Earth. The polymerization rates in space were the same as those on Earth within experimental error. Further development of the ground-based polymerization recipes gave monodisperse particles as large as 100 micrometer with tolerable levels of coagulum, but their uniformity was significantly poorer than the flight latexes. Careful control of the polymerization parameters gave uniform nonspherical particles: symmetrical and asymmetrical doublets, ellipsoids, egg-shaped, ice cream cone-shaped, and popcorn-shaped particles