19,768 research outputs found
Can shared surfaces be safely negotiated by blind and partially sighted people?
‘Shared Space’ schemes are designed to remove the physical distinction between pedestrian space and traffic space in the street environment to encourage more pedestrians to use the area. They may also make it easier for people with wheelchairs, prams or similar to negotiate the space. However, by removing the kerbs, blind and partially sighted people lose one of the key references that they normally use to know they are in a safe space away from vehicles and to navigate around the area. This study is intended to understand what people with visual impairments need from a surface to make it clearly detectable, given that it should not be a barrier to progress for people with other mobility limitations. With this information, some surfaces were tested to determine their suitability as a delineator. Approach and/or Methodology An experimental approach was adopted. People with mobility impairments and blind and partially sighted people were recruited. All participants used the normal street environment unaccompanied. The blind and partially sighted participants included people who use a guide dog, those who use a long cane and those who use no assistive device. The people with mobility impairments all used some form of mobility aid for example walking stick or wheelchair. The tests were run in the pedestrian testing facility PAMELA at UCL. The top surface of the test facility was predominantly concrete paving slab, but with test surfaces discretely located. The task for all participants was to travel from one designated place in the test area to another. For some of these trials the participant would encounter one of the test surfaces, but on other trials they would not. After each trial the participants were asked to rate how easy it was to detect a change in surface, or how easy it was to pass over the surface. The different surfaces included blister paving, corduroy paving, a central delineator, slopes, roughened surfaces, and traditional kerb upstands of different heights. Results or Expected Results None of the 400mm wide surfaces was detected by all participants. Changes in level through slopes were considered both positively and negatively, some people asking for steeper gradients and some less steep. Kerb heights below 60mm were not reliably detectable by blind or partially sighted people and are an obstacle to people in wheelchairs. Further tests on more surfaces are in process and the results will be incorporated into this paper. Conclusion Early suggestions for detectable surfaces – proposed in UK schemes - have been either a barrier to people with mobility impairments, or difficult to detect for blind and partially sighted people or both. The work presented in this paper shows the difficulty in finding a suitable dual purpose surface, yet clarifies the design requirements for shared space delineators for people with mobility impairments and blind or partially sighted people. This work has reinforced the point that 400mm width is insufficient to be used as a tactile surface. Further conclusions will be made after the additional surface tests. Topic Code: Ca C. Accessibility concerns and solutions for those with cognitive and sensory impairment a. Pedestrian safety at crossings and intersection
Self-Consistent Determination of Coupling Shifts in Broken SU(3)
The possibility that certain patterns of SU(3) symmetry breaking are dynamically enhanced in baryon-meson couplings is studied by bootstrap methods. For the strong couplings, a single dominant enhancement is found. It produces very large symmetry-breaking terms, transforming like an octet, as often conjectured. Experimental consequences are listed, such as a reduction of K-baryon couplings relative to π-baryon couplings which is in accord with the experimental weakness of K relative to π production in many circumstances, such as photoproduction and multi-BeV cosmic-ray collisions. For parity-violating nonleptonic couplings, a dominant octet enhancement is again found, as mentioned in a previous paper, which leads to an excellent fit with experiment. For parity-conserving nonleptonic couplings, on the other hand, several different enhancements compete, and the only conclusion we can draw is that terms with the "abnormal" transformation properties brought in by strong symmetry-breaking corrections are present. Our work provides a dynamical derivation of various phenomenological facts associated with SU(6), such as the dominance of the 35 representation in parity-violating nonleptonic decays
Subglacial drainage processes at a High Arctic polythermal valley glacier
Peer reviewedPublisher PD
Structural design of a vertical antenna boresight 18.3 by 18.3-m planar near-field antenna measurement system
A large very precise near-field planar scanner was proposed for NASA Lewis Research Center. This scanner would permit near-field measurements over a horizontal scan plane measuring 18.3 m by 18.3 m. Large aperture antennas mounted with antenna boresight vertical could be tested up to 60 GHz. When such a large near field scanner is used for pattern testing, the antenna or antenna system under test does not have to be moved. Hence, such antennas and antenna systems can be positioned and supported to simulate configuration in zero g. Thus, very large and heavy machinery that would be needed to accurately move the antennas are avoided. A preliminary investigation was undertaken to address the mechanical design of such a challenging near-field antenna scanner. The configuration, structural design and results of a parametric NASTRAN structural optimization analysis are contained. Further, the resulting design was dynamically analyzed in order to provide resonant frequency information to the scanner mechanical drive system designers. If other large near field scanners of comparable dimensions are to be constructed, the information can be used for design optimization of these also
A new fabrication method for precision antenna reflectors for space flight and ground test
Communications satellites are using increasingly higher frequencies that require increasingly precise antenna reflectors for use in space. Traditional industry fabrication methods for space antenna reflectors employ successive modeling techniques using high- and low-temperature molds for reflector face sheets and then a final fit-up of the completed honeycomb sandwich panel antenna reflector to a master pattern. However, as new missions are planned at much higher frequencies, greater accuracies will be necessary than are achievable using these present methods. A new approach for the fabrication of ground-test solid-surface antenna reflectors is to build a rigid support structure with an easy-to-machine surface. This surface is subsequently machined to the desired reflector contour and coated with a radio-frequency-reflective surface. This method was used to fabricate a 2.7-m-diameter ground-test antenna reflector to an accuracy of better than 0.013 mm (0.0005 in.) rms. A similar reflector for use on spacecraft would be constructed in a similar manner but with space-qualified materials. The design, analysis, and fabrication of the 2.7-m-diameter precision antenna reflector for antenna ground tests and the extension of this technology to precision, space-based antenna reflectors are described
An Avoidance Principle with an Application to the Asymptotic Behaviour of Graded Local Cohomology
We present an Avoidance Principle for certain graded rings. As an application
we fill a gap in the proof of a result by Brodmann, Rohrer and Sazeedeh about
the antipolynomiality of the Hilbert-Samuel multiplicity of the graded
components of the local cohomology modules of a finitely generated module over
a Noetherian homogeneous ring with two-dimensional local base ring.Comment: 6 pages; to appear in Journal of Pure and Applied Algebra; corrected
typo
The interactional community: a structural network analysis of community action in three Midwestern towns
The research examines how the structure of individual and organizational interaction within a community influences community action. The analysis is based on data from three rural, Midwestern communities. Data from a survey of community residents, leadership and organizational network data, and profiles of local community action projects are used to examine the relationship between the structure of local interaction and community action. The findings support a structural approach to the interactional community and confirm that social capital (the structure and character of individual interaction) and social infrastructure (the structure of group-level interaction patterns) influence community action processes. The findings have a number of implications for future community research and community development practice, such as the inclusion of network theory and methods as a tool for development of place-based communities
- …