Solar tracking system

A solar tracker for a solar collector is described in detail. The collector is angularly oriented by a motor wherein the outputs of two side-by-side photodetectors are discriminated as to three ranges: a first corresponding to a low light or darkness condition; a second corresponding to light intensity lying in an intermediate range; and a third corresponding to light above an intermediate range, direct sunlight. The first output drives the motor to a selected maximum easterly angular position; the second enables the motor to be driven westerly at the Earth rotational rate; and the third output, the separate outputs of the two photodetectors, differentially controls the direction of rotation of the motor to effect actual tracking of the Sun

Fluorescence Analysis for Multi-Site Aluminum Binding to Natural Organic Matter

Natural organic matter (NOM) samples isolated from different water sources in Norway were compared using their fluorescence properties. Fluorescence surfaces were observed at pH 4.36 and deconvoluted using SIMPLISMA (Windig and Guilment 1991). There were a total of seven different fluorophores observed for these samples and each sampling site had between four and six ofthe fluorescent components. These components were observed to bind Al during titrations at the same pH. Multiresponse titration curves were fit using the method of Smith and Kramer (1998) and most of the binding strengths are similar to values for Suwannee River fulvic acid (1ogK’ between 4.8 and 5.5), but there are strong sites (IogK’ = 7) and weak sites (1ogK’ between 3 and 4) also observed. Results depended on the isolation method used; reverse osmosis and low pressure evaporation yielded different values but with no consistent trends

Solar site test module

A solar site test module using the Rockwell AIM 65microcomputer is described. The module is designed to work at any site where an IBM site data acquisition system (SDAS) is installed and is intended primarily as a troubleshooting tool. It collects sensor information (temperatures, flow rates, etc.) and displays or prints it immediately in calibrated engineering units. It will read one sensor on demand, periodically read up to 10sensors or periodically read all sensors. Performance calculations can also be included with sensor data. Unattended operation is possible to, e.g., monitor a group of sensors once per hour. Work is underway to add a data acquisition system to the test module so that it can be used at sites which have no SDAS

Electrical self-aligning connector

A self-aligning electrical connector device includes a receptacle component having a conically contoured interior and a plug component having a correspondingly contoured conical body receivable in the receptacle component. The plug component has a number of spaced conductive ring elements with a mating face and the receptacle component includes corresponding spaced conductive ring elements providing mating interface with the mating face of the ring elements of the plug component when connected to it. Each ring element of the receptacle component has several segmented portions which defect downwardly when the plug component is inserted. A biasing force is asserted against the face of the ring elements of the plug component providing positive electrical contact and connection between the ring elements of the components

Design definition of a mechanical capacitor

A design study and analyses of a 10 kW-hr, 15 kW mechanical capacitor system was studied. It was determined that magnetically supported wheels constructed of advanced composites have the potential for high energy density and high power density. Structural concepts are analyzed that yield the highest energy density of any structural design yet reported. Particular attention was paid to the problem of 'friction' caused by magnetic and I to the second power R losses in the suspension and motor-generator subsystems, and low design friction levels have been achieved. The potentially long shelf life of this system, and the absence of wearing parts, provide superior performance over conventional flywheels supported with mechanical bearings. Costs and economies of energy storage wheels were reviewed briefly

Engaging the Digitally Engaged Student: Comparing Technology-Mediated Communication Use and Effects on Student Learning

The role of communication technologies in the learning process is both a dynamic and complex issue. Yet, we know surprisingly little about how the use of specific communication technologies may influence classroom performance, key learning outcomes, and other measures of course satisfaction. The research reported here attempts to add to our knowledge about the role of communication in the technology enhanced classroom (TEC) education and in technology-enhanced online (TEO) education through a direct comparison of two courses. Our findings indicate additional support for “The No Significant Difference Phenomenon.” Furthermore, we found that prior experiences lead students to gravitate towards their preferred learning environments, and that basic website elements are required in any learning environment to enhance student outcomes. Finally, we found that when used appropriately, the benefits of communication technology use in education outweigh many of the drawbacks

Composite fermions in bands with N-fold rotational symmetry

We study the effect of band anisotropy with discrete rotational symmetry $C_N$ (where $N\ge 2$) in the quantum Hall regime of two-dimensional electron systems. We focus on the composite Fermi liquid (CFL) at half filling of the lowest Landau level. We find that the magnitude of anisotropy transferred to the composite fermions decreases very rapidly with $N$. We demonstrate this by performing density matrix normalization group calculations on the CFL, and comparing the anisotropy of the composite fermion Fermi contour with that of the (non-interacting) electron Fermi contour at zero magnetic field. We also show that the effective interaction between the electrons after projecting into a single Landau level is much less anisotropic than the band, a fact which does not depend on filling and thus has implications for other quantum Hall states as well. Our results confirm experimental observations on anisotropic bands with warped Fermi contours, where the only detectable effect on the composite Fermi contour is an elliptical distortion ($N = 2$).Comment: 6 pages + bibliography, 5 figure

Solar tracking control system Sun Chaser

The solar tracking control system, Sun Chaser, a method of tracking the Sun in all types of weather conditions is described. The Sun Chaser follows the Sun from east to west in clear or cloudy weather, and resets itself to the east position after sundown in readiness for the next sunrise

Volcanism by melt-driven Rayleigh-Taylor instabilities and possible consequences of melting for admittance ratios on Venus

A large number of volcanic features exist on Venus, ranging from tens of thousands of small domes to large shields and coronae. It is difficult to reconcile all these with an explanation involving deep mantle plumes, since a number of separate arguments lead to the conclusion that deep mantle plumes reaching the base of the lithosphere must exceed a certain size. In addition, the fraction of basal heating in Venus' mantle may be significantly lower than in Earth's mantle reducing the number of strong plumes from the core-mantle boundary. In three-dimensional convection simulations with mainly internal heating, weak, distributed upwellings are usually observed. We present an alternative mechanism for such volcanism, originally proposed for the Earth and for Venus, involving Rayleigh-Taylor instabilities driven by melt buoyancy, occurring spontaneously in partially or incipiently molten regions