51 research outputs found
Raman Tweezers Spectroscopy of Live, Single Red and White Blood Cells
An optical trap has been combined with a Raman spectrometer to make high-resolution measurements of Raman spectra of optically-immobilized, single, live red (RBC) and white blood cells (WBC) under physiological conditions. Tightly-focused, near infrared wavelength light (1064 nm) is utilized for trapping of single cells and 785 nm light is used for Raman excitation at low levels of incident power (few mW). Raman spectra of RBC recorded using this high-sensitivity, dual-wavelength apparatus has enabled identification of several additional lines; the hitherto-unreported lines originate purely from hemoglobin molecules. Raman spectra of single granulocytes and lymphocytes are interpreted on the basis of standard protein and nucleic acid vibrational spectroscopy data. The richness of the measured spectrum illustrates that Raman studies of live cells in suspension are more informative than conventional micro-Raman studies where the cells are chemically bound to a glass cover slip
Micro-Raman Spectroscopy of Silver Nanoparticle Induced Stress on Optically-Trapped Stem Cells
We report here results of a single-cell Raman spectroscopy study of stress effects induced by silver nanoparticles in human mesenchymal stem cells (hMSCs). A high-sensitivity, high-resolution Raman Tweezers set-up has been used to monitor nanoparticle-induced biochemical changes in optically-trapped single cells. Our micro-Raman spectroscopic study reveals that hMSCs treated with silver nanoparticles undergo oxidative stress at doping levels in excess of 2 µg/ml, with results of a statistical analysis of Raman spectra suggesting that the induced stress becomes more dominant at nanoparticle concentration levels above 3 µg/ml
Recent Progress in the Fabrication and Optical Properties of Nanoporous Anodic Alumina.
The fabrication of a thick oxide layer onto an aluminum surface via anodization has been a subject of intense research activity for more than a century, largely due to protective and decorative applications. The capability to create well-defined pores via a cost-effective electrochemical oxidation technique onto the surface has made a major renaissance in the field, as the porous surfaces exhibit remarkably different properties compared to a bulk oxide layer. Amongst the various nanoporous structures being investigated, nanoporous anodic alumina (NAA) with well-organized and highly ordered hexagonal honeycomb-like pores has emerged as the most popular nanomaterial due to its wide range of applications, ranging from corrosion resistance to bacterial repelling surfaces. As compared to conventional nanostructure fabrication, the electrochemical anodization route of NAA with well-controlled pore parameters offers an economical route for fabricating nanoscale materials. The review comprehensively reflects the progress made in the fabrication route of NAA to obtain the material with desired pore properties, with a special emphasis on self-organization and pore growth kinetics. Detailed accounts of the various conditions that can play an important role in pore growth kinetics and pore parameters are presented. Further, recent developments in the field of controlling optical properties of NAA are discussed. A critical outlook on the future trends of the fabrication of NAA and its optical properties on the emerging nanomaterials, sensors, and devices are also outlined
A micro-Raman study of live, single red blood cells (RBCs) treated with AgNO3 nanoparticles.
Silver nanoparticles (Ag NPs) are known to exhibit broad antimicrobial activity. However, such activity continues to raise concerns in the context of the interaction of such NPs with biomolecules. In a physiological environment NPs interact with individual biological cells either by penetrating through the cell membrane or by adhering to the membrane. We have explored the interaction of Ag NPs with single optically-trapped, live erythrocytes (red blood cells, RBCs) using Raman Tweezers spectroscopy. Our experiments reveal that Ag NPs induce modifications within an RBC that appear to be irreversible. In particular we are able to identify that the heme conformation in an RBC transforms from the usual R-state (oxy-state) to the T-state (deoxy-state). We rationalize our observations by proposing a model for the nanoparticle cytotoxicity pathway when the NP size is larger than the membrane pore size. We propose that the interaction of Ag NPs with the cell surface induces damage brought about by alteration of intracellular pH caused by the blockage of the cell membrane transport
Application of HPLC Combined with Laser Induced Fluorescence for Protein Profile Analysis of Tissue Homogenates in Cervical Cancer
A highly objective method, High Performance Liquid Chromatography with Laser Induced Fluorescence (HPLC-LIF) technique was used to study the protein profiles of normal and cervical cancer tissue homogenates. A total of 44 samples including normal cervical biopsy samples from the hysterectomy patients and the patients suffering from different stages of the cervical cancer were recorded by HPLC-LIF and analysed by Principle Component Analysis (PCA) to get statistical information on different tissue components. Discrimination of different stages of the samples was carried out by considering three parameters—scores of factor, spectral residual, and Mahalanobis Distance. Diagnostic accuracy of the method was evaluated using Receiver Operating Characteristic (ROC) analysis, and Youden's index (J) plots. The PCA results showed high sensitivity and specificity (∼100) for cervical cancer diagnosis. ROC and Youden's index curves for both normal and malignant standard sets show good diagnostic accuracy with high AUC values. The statistical analysis has shown that the differences in protein profiles can be used to diagnose biochemical changes in the tissue, and thus can be readily applied for the detection of cervical cancer, even in situations where a histopathology examination is not easy because of nonavailability of experienced pathologists
Recent Progress in the Fabrication and Optical Properties of Nanoporous Anodic Alumina
The fabrication of a thick oxide layer onto an aluminum surface via anodization has been a subject of intense research activity for more than a century, largely due to protective and decorative applications. The capability to create well-defined pores via a cost-effective electrochemical oxidation technique onto the surface has made a major renaissance in the field, as the porous surfaces exhibit remarkably different properties compared to a bulk oxide layer. Amongst the various nanoporous structures being investigated, nanoporous anodic alumina (NAA) with well-organized and highly ordered hexagonal honeycomb-like pores has emerged as the most popular nanomaterial due to its wide range of applications, ranging from corrosion resistance to bacterial repelling surfaces. As compared to conventional nanostructure fabrication, the electrochemical anodization route of NAA with well-controlled pore parameters offers an economical route for fabricating nanoscale materials. The review comprehensively reflects the progress made in the fabrication route of NAA to obtain the material with desired pore properties, with a special emphasis on self-organization and pore growth kinetics. Detailed accounts of the various conditions that can play an important role in pore growth kinetics and pore parameters are presented. Further, recent developments in the field of controlling optical properties of NAA are discussed. A critical outlook on the future trends of the fabrication of NAA and its optical properties on the emerging nanomaterials, sensors, and devices are also outlined
Relevance of echo-structure and texture features:an application in ultrasound breast tumor classification
LASER as a tool for surface modification of dental biomaterials: A review
In recent years, the application of lasers for modifying the surface topography of dental biomaterials has received increased attention. This review paper aims to provide an overview of the current status on the utilization of lasers as a potential tool for surface modification of dental biomaterials such as implants, ceramics, and other materials used for restorative purposes. A literature search was done for articles related to the use of lasers for surface modification of dental biomaterials in English language published between October 2000 and March 2023 in Scopus, Pubmed and web of science, and relevant articles were reviewed.Lasers have been mainly used for surface modification of implant materials (71%), especially titanium and its alloys, to promote osseointegration. In recent years, laser texturing has also emerged as a promising technique to reduce bacterial adhesion on titanium implant surfaces. Currently, lasers are being widely used for surface modifications to improve osseointegration and reduce peri-implant inflammation of ceramic implants and to enhance the retention of ceramic restorations to the tooth. The studies considered in this review seem to suggest laser texturing to be more proficient than the conventional methods of surface modification. Lasers can alter the surface characteristics of dental biomaterials by creating innovative surface patterns without significantly affecting their bulk properties. With advances in laser technology and availability of newer wavelengths and modes, laser as a tool for surface modification of dental biomaterials is a promising field, with excellent potential for future research
The average spectra of control and Ag NP treated RBCs 45-incubation.
<p>(A) Control, (B) 1 µl Ag NPs, (C) 5 µl Ag NPs, and (D) 10 µl Ag NPs.</p
- …