147 research outputs found
Continuation of tailored composite structures of ordered staple thermoplastic material
The search for the cost effective composite structure has motivated the investigation of several approaches to develop composite structure from innovative material forms. Among the promising approaches is the conversion of a planar sheet to components of complex curvature through sheet forming or stretch forming. In both cases, the potential for material stretch in the fiber direction appears to offer a clear advantage in formability over continuous fiber systems. A framework was established which allows the simulation of the anisotropic mechanisms of deformation of long discontinuous fiber laminates wherein the matrix phase is a viscous fluid. Predictions for the effective viscosities of a hyper-anisotropic medium consisting of collimated, discontinuous fibers suspended in viscous matrix were extended to capture the characteristics of typical polymers including non-Newtonian behavior and temperature dependence. In addition, the influence of fiber misorientation was also modeled by compliance averaging to determine ensemble properties for a given orientation distribution. A design tool is presented for predicting the effect of material heterogeneity on the performance of curved composite beams such as those used in aircraft fuselage structures. Material heterogeneity can be induced during manufacturing processes such as sheet forming and stretch forming of thermoplastic composites. This heterogeneity can be introduced in the form of fiber realignment and spreading during the manufacturing process causing radial and tangential gradients in material properties. Two analysis procedures are used to solve the beam problems. The first method uses separate two-dimensional elasticity solutions for the stresses in the flange and web sections of the beam. The separate solutions are coupled by requiring that forces and displacements match section boundaries. The second method uses an approximate Rayleigh-Ritz technique to find the solutions for more complex beams. Analyses are performed for curved beams of various cross-sections loaded in pure bending and with a uniform distributed load. Preliminary results show that the geometry of the beam dictates the effect of heterogeneity on performance. The role of heterogeneity is larger in beams with a small average radius-to-depth ration, R/t, where R is the average radius of the beam and t is the difference between the inside and outside radii. Results of the anlysis are in the form of stresses and displacements and are compared to both mechanics of materials and numerical solutions obtained using finite element analysis
Structure-Property Relationship in Ionomer Membranes
Perfluorosulfonic acid (PFSA) ionomer membranes are ion-conducting polymers with high water sorption capacity and thermo-mechanical stability. The morphology of PFSA changes during sorption affecting the mechanical and physical properties of the membrane. In this work, we investigate the structure-property relationship in swollen PFSA membranes using three proposed nanostructural descriptions and determine Young\u27s modulus of the membrane at a wide range of temperatures (−20–85°C) and water volume fractions (0–0.5) for these configurations. Comparing the mechanics-based models with experimental data we propose that ion-rich water domains in PFSA membrane are spherical at low water content, spherical with connecting channels at intermediate water content and cylindrical at high water contents. Furthermore, our findings indicate that the scaling behavior for Young\u27s modulus of PFSA ionomers is similar to that of aerogels. This suggests, from a mechanics perspective, that aerogels and ionomers may have a similar interconnected porous nanostructure where some solid regions do not contribute to the mechanical load-bearing capacity
Aspects of Fatigue Failure Mechanisms in Polymer Fuel Cell Membranes
The swelling-driven fatigue behavior of polymer fuel cell membranes during relative humidity (RH) cycling is investigated. In particular, swelling-induced membrane stresses are obtained from a numerical model simulating fuel cell RH cycle tests, and compared to the lifetimes obtained experimentally from tests conducted in the absence of electrochemical effects. A strong correlation between the lifetimes of the membranes in the actual tests and model results is obtained. In general, higher RH (or swelling) amplitude results in larger stress amplitudes and shorter lifetime, that is, fewer cycles to failure. Tensile stresses are needed for forming local cavities in the membrane, which may eventually lead to craze formation. Cavitation is less likely to occur in compressed membrane at high humidities. The stress–lifetime plots for polymer fuel cell membranes exhibit similar features to those observed for other polymers. The crazing criterion for polymers suggests that craze initiation during RH cycling is more likely to occur in the low compression regions, such as under the channels, which is in agreement with experimental observations. © 2011 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 49: 1506–1517, 201
Long discontinuous fiber composite structure: Forming and structural mechanics
Cost effective composite structure has motivated the investigation of several new approaches to develop composite structure from innovative material forms. Among the promising new approaches is the conversion of planar sheet to components of complex curvature through sheet forming or stretch forming. In both cases, the potential for material stretch in the fiber direction appears to offer a clear advantage in formability over continuous fiber systems. In the present study, the authors have established a framework which allows the simulation of the anisotropic mechanisms of deformation of long discontinuous fiber laminates wherein the matrix phase is a viscous fluid. The initial study focuses upon the establishment of micromechanics models for prediction of the effective anisotropic viscosities of the oriented fiber assembly in a viscous matrix. Next, the developed constitutive relation is employed through an analogy with incompressible elasticity to exercise the finite element technique for determination of local fiber orientation and laminate thickness after forming. Results are presented for the stretch bending of a curved beam from an arbitrary composite laminate and the bulging of a clamped sheet. Structural analyses are conducted to determine the effect of microstructure on the performance of curved beams manufactured from long discontinuous fiber composites. For the purposes of this study, several curved beams with ideal and non-ideal microstructures are compared for response under pure bending. Material parameters are determined from a separate microstructural analysis
Mechanical Behavior of Fuel Cell Membranes under Humidity Cycles and Effect of Swelling Anisotropy on the Fatigue Stresses
The mechanical response of proton exchange membranes in a fuel cell assembly is investigated under humidity cycles at a constant temperature (85°C). The behavior of the membrane under hydration–dehydration cycles is simulated by imposing a humidity gradient from the cathode to the anode. Linear elastic, plastic constitutive behavior with isotropic hardening and temperature and humidity dependent material properties are utilized in the simulations for the membrane. The evolution of the stresses and plastic deformation during the humidity cycles are determined using finite element analysis for two clamping methods and various levels of swelling anisotropy. The membrane response strongly depends on the swelling anisotropy where the stress amplitude decreases with increasing anisotropy. These results suggest that it may be possible to optimize a membrane with respect to swelling anisotropy to achieve better fatigue resistance, potentially enhancing the durability of fuel cell membranes
Mechanical Behavior of Fuel Cell Membranes under Humidity Cycles and Effect of Swelling Anisotropy on the Fatigue Stresses
The mechanical response of proton exchange membranes in a fuel cell assembly is investigated under humidity cycles at a constant temperature (85°C). The behavior of the membrane under hydration–dehydration cycles is simulated by imposing a humidity gradient from the cathode to the anode. Linear elastic, plastic constitutive behavior with isotropic hardening and temperature and humidity dependent material properties are utilized in the simulations for the membrane. The evolution of the stresses and plastic deformation during the humidity cycles are determined using finite element analysis for two clamping methods and various levels of swelling anisotropy. The membrane response strongly depends on the swelling anisotropy where the stress amplitude decreases with increasing anisotropy. These results suggest that it may be possible to optimize a membrane with respect to swelling anisotropy to achieve better fatigue resistance, potentially enhancing the durability of fuel cell membranes
Public awareness of and attitudes towards research biobanks in Latvia
Background: Public awareness and engagement are among the main prerequisites for protecting the rights of research participants and for successful and sustainable functioning of research biobanks. The aim of our study was to analyse public awareness and attitudes towards research biobanks in Latvia, and to compare these data with the results of the 2010 Eurobarometer study. We also analysed the influence of awareness and attitudes towards biobanks on willingness to participate in biobank studies and on preferred type of informed consent. Methods: We developed a 12-question survey repeating seven questions about biobanks from the 2010 Eurobarometer questionnaire and adding five others. After describing the study variables, we performed a two-stage analysis of the results. In the first stage we analysed differences between the answers from 2010 and 2019 and conducted univariate analyses of relationships among particular variables, and between those variables and the socio-demographic characteristics of participants. In the second stage we investigated multivariable associations of willingness to participate and type of consent with awareness, trust and the socio-economic characteristics of participants. Results: According to our study, the general public in Latvia is still not well informed about research biobanks. Fewer respondents have heard about research biobanks than in 2010. At the same time, the number of respondents who are willing to donate biological samples and personal data to a biobank has increased, e.g. the number of respondents who would definitely or probably be willing to provide information about themselves has increased from 25.8.% to 40.7 since 2010. Overall, concerns about the donation of different types of biological samples and data to a biobank have slightly decreased. Conclusions: Public awareness about biobanks is important for their sustainability. It needs to be increased not only by traditional methods of informing the public, but also by more innovative and participatory approaches, e.g. by citizen science projects. There is a need to strengthen the public visibility and trustworthiness of ethics committees in Latvia in the field of biobanking
Numerical Investigation of Mechanical Durability in Polymer Electrolyte Membrane Fuel Cells
The relationship between the mechanical behavior and water transport in the membrane electrode assembly (MEA) is numerically investigated. Swelling plays a key role in the mechanical response of the MEA during fuel cell operation because swelling can be directly linked to the development of stresses. Thus, in the model introduced here, the stresses and the water distribution are coupled. Two membranes are studied: unreinforced perfluorosulfonic acid (PFSA) and an experimental reinforced composite membrane. The results suggest that open-circuit voltage operations lead to a uniform distribution of stresses and plastic deformation, whereas under current-load operation, the stresses and the plastic deformation are generally lower and localized at the cathode side of the MEA. For the experimental reinforced membrane investigated, the in-plane swelling and, consequently, the stresses and plastic deformation are lower than in an unreinforced PFSA membrane. This reduction is a favorable outcome for improving durability. The model also suggests that the mechanical constraints due to the clamping of the cell may limit the swelling of the membrane and consequently change the water distribution
Stresses in Proton Exchange Membranes Due to Hygro-Thermal Loading
Durability of the proton exchange membrane (PEM) is a major technical barrier to the commercial viability of polymer electrolyte membrane fuel cells (PEMFC) for stationary and transportation applications. In order to reach Department of Energy objectives for automotive PEMFCs, an operating design lifetime of at least 5000 h over a broad temperature range is required. Reaching these lifetimes is an extremely difficult technical challenge. Though good progress has been made in recent years, there are still issues that need to be addressed to assure successful, economically viable, long-term operation of PEM fuel cells. Fuel cell lifetime is currently limited by gradual degradation of both the chemical and hygro-thermomechanical properties of the membranes.Eventually the system fails due to a critical reduction of the voltage or mechanical damage. However, the hygro-thermomechanical loading of the membranes and how this effects the lifetime of thefuel cell is not understood. The long-term objective of the research is to establish a fundamental understanding of the mechanical processes in degradation and how they influence the lifetime of PEMFCs based on perfluorosulfuric acid membrane. In this paper, we discuss the finite element models developed to investigate the in situ stresses in polymer membranes
Time-Dependent Mechanical Behavior of Proton Exchange Membrane Fuel Cell Electrodes
The electrodes used for Proton Exchange Membrane Fuel Cells (PEMFCs) are typically painted or sprayed onto the membrane during manufacturing, making it difficult to directly characterize their mechanical behavior as a stand-alone material. An experimental-numerical hybrid technique is devised to extract the electrode properties from the experimentally measured properties of Nafion® 211 membrane1 and a membrane electrode assembly (MEA) based on Nafion® 211 membrane at various temperatures, humidities, and strain rates. Within the linear regime, the rule-of-mixtures assuming an iso-strain condition is used to calculate the rate-dependent Young\u27s modulus of the electrodes. Beyond the linear regime, reverse analysis is conducted using finite element models of the MEA to determine the non-linear behavior of the electrodes. The mechanical damage mechanisms that occur in the MEA during tensile loading are also investigated through interrupted tension tests and then incorporated into the finite element models for determining the electrode behavior. The results suggest that the electrodes have similar behavior to Nafion® 211 membrane as functions of strain rate, temperature and humidity, but with lower Young\u27s modulus and proportional limit
- …