Gas barrier polymer nanocomposite films prepared by graphene oxide encapsulated polystyrene microparticles

The dispersion and orientation of two-dimensional (2D) inorganic nanoplatelets in polymers are technical challenges faced in polymer nanocomposite manufacturing. This work demonstrates an effective way to facilitate the dispersion and orientation of graphene oxide (GO) nanoplatelets in a polymer matrix through encapsulating the polymer within a nanoplatelet shell. Briefly, few-layered GO nanoplatelets encapsulated polystyrene (PS) microparticles were synthesized by a Pickering suspension polymerization method. The synthesis conditions, morphologies, and barrier properties of the GO encapsulated PS spheres and the melt-compressed films are characterized. The addition of salt induces flocculation of GO onto the surface of the styrene monomer droplet, resulting in the formation of a multilayered GO shell as well as the sedimenting of the PS/GO particles during polymerization. The obtained GO encapsulated PS microspheres were purified, dried, and melt-compressed to form composite films. The oxygen permeability (expressed as transmission rate) of the PS/GO composite film containing 2 wt % GO was 526.02 ± 55.78 cm3 m–2 24 h–1—a reduction of 96% relative to the PS control film and 34% lower than the solution mixed PS/GO composite film. This indicates that the encapsulated PS spheres act as an effective carrier to facilitate the dispersion of GO. The orientation was realized by the following melt-compression process, which creates tortuous pathways hindering the permeation of gases through the PS matrix

Photocatalytic Nanolithography of Self-Assembled Monolayers and Proteins

Self-assembled monolayers of alkylthiolates on gold and alkylsilanes on silicon dioxide have been patterned photocatalytically on sub-100 nm length-scales using both apertured near-field and apertureless methods. Apertured lithography was carried out by means of an argon ion laser (364 nm) coupled to cantilever-type near-field probes with a thin film of titania deposited over the aperture. Apertureless lithography was carried out with a helium–cadmium laser (325 nm) to excite titanium-coated, contact-mode atomic force microscope (AFM) probes. This latter approach is readily implementable on any commercial AFM system. Photodegradation occurred in both cases through the localized photocatalytic degradation of the monolayer. For alkanethiols, degradation of one thiol exposed the bare substrate, enabling refunctionalization of the bare gold by a second, contrasting thiol. For alkylsilanes, degradation of the adsorbate molecule provided a facile means for protein patterning. Lines were written in a protein-resistant film formed by the adsorption of oligo(ethylene glycol)-functionalized trichlorosilanes on glass, leading to the formation of sub-100 nm adhesive, aldehyde-functionalized regions. These were derivatized with aminobutylnitrilotriacetic acid, and complexed with Ni2+, enabling the binding of histidine-labeled green fluorescent protein, which yielded bright fluorescence from 70-nm-wide lines that could be imaged clearly in a confocal microscope

STM studies and electrochemical applications of self-assembled monolayers on silicon

EThOS - Electronic Theses Online ServiceGBUnited Kingdo

Efficient self-assembly of DNA-functionalized fluorophores and gold nanoparticles with DNA functionalized silicon surfaces: the effect of oligomer spacers

Although strategies for the immobilization of DNA oligonucleotides onto surfaces for bioanalytical and top-down bio-inspired nanobiofabrication approaches are well developed, the effect of introducing spacer molecules between the surface and the DNA oligonucleotide for the hybridization of nanoparticle–DNA conjugates has not been previously assessed in a quantitative manner. The hybridization efficiency of DNA oligonucleotides end-labelled with gold nanoparticles (1.4 or 10 nm diameter) with DNA sequences conjugated to silicon surfaces via hexaethylene glycol phosphate diester oligomer spacers (0, 1, 2, 6 oligomers) was found to be independent of spacer length. To quantify both the density of DNA strands attached to the surfaces and hybridization with the surface-attached DNA, new methodologies have been developed. Firstly, a simple approach based on fluorescence has been developed for determination of the immobilization density of DNA oligonucleotides. Secondly, an approach using mass spectrometry has been created to establish (i) the mean number of DNA oligonucleotides attached to the gold nanoparticles and (ii) the hybridization density of nanoparticle–oligonucleotide conjugates with the silicon surface–attached complementary sequence. These methods and results will be useful for application with nanosensors, the self-assembly of nanoelectronic devices and the attachment of nanoparticles to biomolecules for single-molecule biophysical studies

Self-assembly of semifluorinated n-alkanethiols on {111}-oriented Au investigated with scanning tunneling microscopy experiment and theory

The adsorption of semifluorinated alkanethiols on Au/mica was studied by scanning tunneling microscopy (STM). The adlayer structure produced is based on a p(2 x 2) structure though lines of molecules displayed extensive kinks and bends. In addition, a considerable variation in the contrast of molecular features is found. Molecular modeling calculations confirm that, for the fluorinated thiols, inequivalently adsorbed molecules within a p(2 x 2) registry are present, an aspect that endows the local structure of the adlayer with a higher flexibility in comparison to nonfluorinated thiols, where one adsorption site is strongly favored in a (root 3 x root 3)R30 degrees structure. Simulated STM imaging on the optimized systems successfully recovered the effects on the molecular feature contrast induced by the flexibility of the fluorinated thiol adlayer. (C) 2007 American Institute of Physics.</p

Photocatalytic Nanolithography of Self-Assembled Monolayers and Proteins

Self-assembled monolayers of alkylthiolates on gold and alkylsilanes on silicon dioxide have been patterned photocatalytically on sub-100 nm length-scales using both apertured near-field and apertureless methods. Apertured lithography was carried out by means of an argon ion laser (364 nm) coupled to cantilever-type near-field probes with a thin film of titania deposited over the aperture. Apertureless lithography was carried out with a helium–cadmium laser (325 nm) to excite titanium-coated, contact-mode atomic force microscope (AFM) probes. This latter approach is readily implementable on any commercial AFM system. Photodegradation occurred in both cases through the localized photocatalytic degradation of the monolayer. For alkanethiols, degradation of one thiol exposed the bare substrate, enabling refunctionalization of the bare gold by a second, contrasting thiol. For alkylsilanes, degradation of the adsorbate molecule provided a facile means for protein patterning. Lines were written in a protein-resistant film formed by the adsorption of oligo(ethylene glycol)-functionalized trichlorosilanes on glass, leading to the formation of sub-100 nm adhesive, aldehyde-functionalized regions. These were derivatized with aminobutylnitrilotriacetic acid, and complexed with Ni2+, enabling the binding of histidine-labeled green fluorescent protein, which yielded bright fluorescence from 70-nm-wide lines that could be imaged clearly in a confocal microscope.ISSN:1936-0851ISSN:1936-086

Improvement in the Electrical Properties of Nickel Plated Steel using Graphitic Carbon Coatings

Thin layers of highly conductive graphitic carbon have been deposited onto nickel plated steel substrates using a direct photothermal chemical vapour deposition (PTCVD) technique. The coated nickel plated steel substrates have improved electrical properties (sheet resistance and interfacial contact resistance) compared to the pristine nickel plated steel, which makes it a cost effective alternative to stainless steel for steel producers to use in high-end electrical applications such as energy storage and microelectronics. The coated nickel plated steel has been found to have an approximately 10% reduction in sheet resistance, and a 200 times reduction in interfacial contact resistance (under compression at 140 N cm-2), compared to the pristine nickel plated steel. The interfacial contact resistance is also three times lower than that of a benchmark gold coated stainless steel equivalent at the same pressure