7,573 research outputs found
FORTRAN program for calculating leading and trailing-edge geometry of turbomachine blades
A FORTRAN IV program which calculates leading- and trailing-edge circle radii, tangency angles on the leading- and trailing-edge circles, and stagger angles of turbomachinery blade sections using only spline points defining the blade surfaces is described. The program shifts the origin of the blade coordinates to the leading edge of the blade. Required input includes (m, theta) coordinates of a sufficient number of spline points to adequately define the two surfaces of the blade. Other required input are the radii from the axis of rotation of the leading- and trailing-edges. The output from this program is used directly as the geometrical input for a NASA developed program for calculating transonic velocities on a blade-to-blade stream surface of a turbomachine. The program is used for axial, radial, and mixed flow turbomachine blades
Aerodynamic design of a free power turbine for a 75 KW gas turbine automotive engine
A single stage axial-flow turbine having a tip diameter of 15.41 centimeters was designed. The design specifications are given and the aerodynamic design procedure is described. The design includes the transition duct and the turbine exit diffuser. The aerodynamic information includes typical results of a parametric study, velocity diagrams, blade surface and wall velocities, and blade profile and wall coordinates
Performance of a tandem-rotor/tandem-stator conical-flow compressor designed for a pressure ratio of 3
A conical-flow compressor stage with a large radius change through the rotor was tested at three values of rotor tip clearance. The stage had a tandem rotor and a tandem stator. Peak efficiency at design speed was 0.774 at a pressure ratio of 2.613. The rotor was tested without the stator, and detailed survey data were obtained for each rotor blade row. Overall peak rotor efficiency was 0.871 at a pressure ratio of 2.952
Event generation with SHERPA 1.1
In this paper the current release of the Monte Carlo event generator Sherpa,
version 1.1, is presented. Sherpa is a general-purpose tool for the simulation
of particle collisions at high-energy colliders. It contains a very flexible
tree-level matrix-element generator for the calculation of hard scattering
processes within the Standard Model and various new physics models. The
emission of additional QCD partons off the initial and final states is
described through a parton-shower model. To consistently combine multi-parton
matrix elements with the QCD parton cascades the approach of Catani, Krauss,
Kuhn and Webber is employed. A simple model of multiple interactions is used to
account for underlying events in hadron--hadron collisions. The fragmentation
of partons into primary hadrons is described using a phenomenological
cluster-hadronisation model. A comprehensive library for simulating tau-lepton
and hadron decays is provided. Where available form-factor models and matrix
elements are used, allowing for the inclusion of spin correlations; effects of
virtual and real QED corrections are included using the approach of Yennie,
Frautschi and Suura.Comment: 47 pages, 21 figure
Experimental performance of a 16.10-centimeter-tip-diameter sweptback centrifugal compressor designed for a 6:1 pressure ratio
A backswept impeller with design mass flow rate of 1.033 kg/sec was tested with both a vaned diffuser and a vaneless diffuser to establish stage and impeller characteristics. Design stage pressure ratio of 5.9:1 was attained at a flow slightly lower than the design value. Flow range at design speed was 6 percent of choking flow. Impeller axial tip clearance at design speed was varied to determine effect on stage and impeller performance
Experimental performance of a 13.65-centimeter-tip-diameter tandem-bladed sweptback centrifugal compressor designed for a pressure ratio of 6
A 13.65 cm tip diameter backswept centrifugal impeller having a tandem inducer and a design mass flow rate of 0.907 kg/sec was experimentally investigated to establish stage and impeller characteristics. Tests were conducted with both a cascade diffuser and a vaneless diffuser. A pressure ratio of 5.9 was obtained near surge for the smallest clearance tested. Flow range at design speed was 6.3 percent for the smallest clearance test. Impeller exit to shroud axial clearance at design speed was varied to determine the effect on stage and impeller performance
Effect of area ratio on the performance of a 5.5:1 pressure ratio centrifugal impeller
A centrifugal impeller which was initially designed for a pressure ratio of approximately 5.5 and a mass flow rate of 0.959 kg/sec was tested with a vaneless diffuser for a range of design point impeller area ratios from 2.322 to 2.945. The impeller area ratio was changed by successively cutting back the impeller exit axial width from an initial value of 7.57 mm to a final value of 5.97 mm. In all, four separate area ratios were tested. For each area ratio a series of impeller exit axial clearances was also tested. Test results are based on impeller exit surveys of total pressure, total temperature, and flow angle at a radius 1.115 times the impeller exit radius. Results of the tests at design speed, peak efficiency, and an exit tip clearance of 8 percent of exit blade height show that the impeller equivalent pressure recovery coefficient peaked at a design point area ratio of approximately 2.748 while the impeller aerodynamic efficiency peaked at a lower value of area ratio of approximately 2.55. The variation of impeller efficiency with clearance showed expected trends with a loss of approximately 0.4 points in impeller efficiency for each percent increase in exit axial tip clearance for all impellers tested
- …