10 research outputs found
Evaluation of residence time on nitrogen oxides removal in non-thermal plasma reactor
Non-thermal plasma (NTP) has been introduced over the last few years as a promising after- treatment system for nitrogen oxides and particulate matter removal from diesel exhaust. NTP technology has not been commercialised as yet, due to its high rate of energy consumption. Therefore, it is important to seek out new methods to improve NTP performance. Residence time is a crucial parameter in engine
exhaust emissions treatment. In this paper, different electrode shapes are analysed and the corresponding residence time and NOx removal efficiency are studied. An axisymmetric laminar model is used for obtaining residence time distribution numerically using FLUENT software. If the mean residence time in a NTP plasma reactor increases, there will be a corresponding increase in the reaction time and consequently the pollutant removal efficiency increases. Three different screw thread electrodes and a rod electrode are examined. The results show the advantage
of screw thread electrodes in comparison with the rod electrode. Furthermore,between the screw thread electrodes, the electrode with the thread width of 1 mm has the highest NOx removal due to higher residence time and a greater number of micro-discharges. The results show that the residence time of the screw thread electrode with a thread width of 1 mm is 21% more than for the rod electrode
Kinetics & Mechanism of Oa(VIII)-catalysed Oxidation of Cyc1ohexanone by Periodate in Alkaline Medium
1095-109
Treatment of NOx from Diesel Engine Exhaust by Dielectric Barrier Discharge Method
This paper reports improved performance of advantages when compared to its counterpart as it is cost discharge plasma in filtered engine exhaust treatment. Our effective, low capital and operation costs, salable by- paper deals about the removal of NOX emissions from the diesel products, and integration with the existing systems. In this exhaust by electric discharge plasma. For the treatment of diesel paper we describe an alternate reactor geometry referred to exhaust a new type of reactor referred to as cross-flow dielectric as cross-flow DBD reactor, where the exhaust gas flow barrier discharge reactor has been used, where the gas flow is perpendicular to the wire-cylinder reaction chamber. This perpendicular to the corona electrode. Experiments were reactor is used to treat the actual exhaust of a 3.75 kW diesel- conducted at different flow rates ranging from 2 l/min to 10 l/ generator set. The main emphasis is laid on the NOX treatment min. The discharge plasma assisted barrier discharge reactor of diesel engine exhaust. Experiments were carried out at has shown promising results in NOX removal at high flow rates
Application of Solar Powered High Voltage Discharge Plasma for NOX Removal in Diesel Engine Exhaust
This paper proposes a compact electric discharge plasma source for controlling NOX emission in diesel engine
exhaust. Boost converter is used to boost to solar powered
battery voltage to 24V, further an automobile ignition coil was used to generate the high voltage pulse using fly-back
topology. This design is aimed at retrofitting the existing
catalytic converters with pulse assisted cleaning technique. In this paper we bring out a relative comparison of discharge plasma and plasma-adsorbent process at different gas flow rates. Activated alumina was used as adsorbent. The main emphasis is laid on the development of a compact pulse source from 12V battery, which is powered by the solar, for the removal of NOX from the filtered diesel engine exhaust
Application of Solar Powered High Voltage Discharge Plasma for NOX Rem
This paper proposes a compact electric discharge plasma source for controlling NOX emission in diesel engine exhaust. Boost converter is used to boost to solar powered
battery voltage to 24V, further an automobile ignition coil was used to generate the high voltage pulse using fly-back
topology. This design is aimed at retrofitting the existing
catalytic converters with pulse assisted cleaning technique. In this paper we bring out a relative comparison of discharge plasma and plasma-adsorbent process at different gas flow rates. Activated alumina was used as adsorbent. The main emphasis is laid on the development of a compact pulse source from 12V battery, which is powered by the solar, for the removal of NOX from the filtered diesel engine exhaust
Mechanical and barrier properties of polyvinyl chloride plasticized with dioctyl phthalate, epoxidized soybean oil, and epoxidized cardanol
Quantitative analysis of the community structure of tropical amphibian assemblages and its significance to conservation
Influence of non-thermal plasma after-treatment technology on diesel engine particulate matter composition and NOx concentration
The effect of non-thermal plasma technology for particulate matter removal and nitrogen oxide emission reduction from diesel exhaust has been investigated. A sample of exhaust was cooled to the ambient temperature and passed through a dielectric barrier discharge reactor. This reactor was employed for producing plasma inside the diesel exhaust. A range of discharge powers by varying the applied voltage from 7.5 to 13.5 kV (peak–peak) at a frequency of 50 Hz has been evaluated during the experiments. Regarding the NOx emission concentration, the maximum removal efficiency has been achieved at energy density of 27 J/L. Soot, soluble organic fraction and sulphate components of diesel particulate matter have been analysed separately, and the consequence of plasma exposure on particle size distribution on both the nucleation and accumulation modes has been studied. Plasma was found to be very effective for soot removal, and it could approach complete removal efficiency for accumulation mode particles. However, when applied voltage approached 12 kV, the total number of nucleation mode particles increased by a factor of 50 times higher than the total particle numbers at the reactor inlet. This increase in nucleation mode particles increased even more when applied voltage was set at 13.5 kV