A 10-way power divider based on a transducer and a radial junction operating in the circular TM01 mode

This work presents a 10-way Ku-band power divider using a mode transducer and a radial junction connected by an overmoded circular waveguide operating in the TM 01 mode. The circular symmetry of this mode has been exploited to obtain a power divider with the rectangular output ports radially distributed along the broad wall of the waveguides in H-plane configuration. This topology provides the same amplitude and phase for all the output ports. At the same time, a compact profile has been obtained, introducing a simple manufacturing for the two components of the divider. The first component is a mode transducer converting the TE 10 mode in the rectangular waveguide to the TM 01 mode in the circular waveguide. It is based on a novel topology providing a very high purity in the mode conversion with an attenuation for the other propagating mode, the TE 11c , higher than 60 dB. The second component is a 10-way radial junction that must work under the excitation of the TM 01 , whose special features, since this mode is not the fundamental one of the circular waveguide, will be highlighted. The final design has been validated with an experimental prototype, proposing a manufacturing based on four simple parts. This has been the key to obtain an experimental prototype with specifications in the state-of-the-art. The measured efficiency is better than 96.5% in a 16.7% relative frequency bandwidth from 11 GHz to 13 GHz, with return losses better than 25 dB in the common port. The measured difference between the signals at the output ports of the prototype is ±0.3 dB for the amplitudes and ±0.45° for the phases. A comparison of the obtained results with another divider based on the TE 01 mode shows the potential of the presented design for becoming an alternative to the more extended TE 01 -based power dividersThis work was supported by the Spanish Government through the Agencia Estatal de Investigacion, Fondo Europeo de Desarrollo Regional (AEI/FEDER, UE), under Grant TEC2016-76070-C3-1/2-R (ADDMATE

Development of a high-performance W-band duplexer for plasma diagnosis using a single band with dual circular polarization

Discrepancia entre la información que aparece en el artículo que indica que el copyright es de Elsevier, y la información que aparece en la página de la revista y en el Copyright Clearance Center que indican © 2019 The Authors. Published by Elsevier B.V., así como que el artículo está publicado en Open Access under a Creative Commons licenceThis work presents the design and experimental validation of a high performance, compact, waveguide duplexer operating from 91.5 to 96.5 GHz for its integration in diverse W-band microwave equipment as in plasma diagnosis applications. It uses a single frequency band, with two signals discriminated by different orthogonal circular polarization, which is generated by means of a septum orthomode transducer (OMT) polarizer. Moreover, this component is optimized loaded with the horn antenna for improving the overall system performance. It is explained how these two components are integrated into a very compact duplexer, designed using efficient numerical algorithms. The manufacturing process by mean of high precision milling, and including electrical discharge machining (EDM) has led to excellent performances. The measured return loss level and isolation are higher than 30 dB, and the insertion loss level is below 0.3 dB. Finally, the key parameter in this device, which reflects the symmetry in the manufacturing process, i.e., the axial ratio, is lower than 0.6 dB for both polarizations, an excellent result showing the potential of the presented designThis work was supported by the Spanish government under grants (ADDMATE) TEC2016-76070-C3-1/2-R (Agencia Estatal de Investigación, Spain, Fondo Europeo de Desarrollo Regional: AEI/FEDER/UE) and the program of Comunidad de Madrid, Spain S2013/ICE-3000 (SPADERADARCM

High-performance 16-way Ku-band radial power combiner based on the TE01-circular waveguide mode

This work presents a 16-way Ku-band radial power combiner for high power and high frequency applications, using the very low loss TE01 circular waveguide mode. The accomplished design shows an excellent performance: the experimental prototype has a return loss better than 30 dB, with a balance for the amplitudes of ( 0.15 dB) and ( 2.5 ) for the phases, in a 16.7% fractional bandwidth (2 GHz centered at 12 GHz). For obtaining these outstanding specifications, required, for instance, in highfrequency amplification or on plasma systems, a rigorous step-by-step procedure is presented. First, a high-purity mode transducer has been designed, from the TE10 mode in the rectangular waveguide to the TE01 mode in the circularwaveguide, with very high attenuation (>50 dB) for the other propagating and evanescent modes in the circularwaveguide. This transducer has been manufactured and measured in a back-to-back configuration, validating the design process. Second, an E-plane 16-way radial power divider has been designed, where the power is coupled from the 16 non-reduced-height radial standardwaveguides into the TE01 circularwaveguide mode, improving the insertion loss response and removing the usual tapered transformers of previous designs limiting the power handling. Finally, both the transducer and the divider have been assembled to make the final radial combiner. The prototype has been carefully manufactured, showing very good agreement between the measurements and the full-wave simulationsThe authors would like to thank INMEPRE S.A., the diligence in the manufacturing process. This work was supported by the Spanish government under Grant (ADDMATE) No. TEC2016-76070-C3-1/2-R (AEI/FEDER/UE) and the program of Comunidad de Madrid S2013/ICE-3000 (SPADERADARCM

Design of Radial Power Combiners Based on TE 01 Circular Waveguide Mode

Modern microwave and millimeter-wave systems require high-power amplifiers in very diverse fields such as communications or plasma physics. Although amplification technology has significantly evolved in the last decades, a single module is not enough for achieving the required power level. The solution in this case is the combination of several individual modules with power combiners. In this chapter, this concept is shown with two E-plane radial power combiners, both carrying a high-power signal with the circular waveguide TE01 mode. The first design is a 16-way Ku-band combiner with an excellent experimental performance: return loss better than 30 dB, with a balance for the amplitudes of ±0.15 dB and ±2.5o for the phases, in a 16.7% fractional bandwidth (2 GHz centered at 12 GHz), and efficiency better than 95% in this band. The second design is a 5-way W-band combiner, showing excellent characteristics as well: the experimental prototype has a return loss better than 20 dB, with a balance for the amplitudes of ±0.4 dB and ±3.5o for the phases, in a 12.8% fractional bandwidth (12 GHz centered at 94 GHz), and efficiency better than 85% in this whole band. The experimental results obtained in both designs are the state of the art in the area of radial power combiners

Additive manufacturing of a compact Ku-band orthomode transducer

This work presents a compact ortho-mode transducer (OMT) built by additive manufacturing in a single-block, reducing the number of parts and flanges and improving the losses and power handling capability. The single-block approach also reduces potential passive intermodulation issues since the number of interfaces between parts is minimized. The presented OMT is based on the T-junction topology, with a short-circuited common circular waveguide where the two rectangular waveguides ports are attached. Both ports are arranged in opposite direction to maintain a symmetry plane for the whole structure in order to obtain a high isolation. Specific matching elements are introduced for each polarization to route the orthogonal modes to the common waveguide. The device is built by Selective Laser Melting (SLM), which imposes a set of specific mechanical restrictions to the 3D model of the OMT. The proposed design incorporates those restrictions, simplifying the geometry of the OMT as much as possible (especially the routing elements) to simplify the manufacturing. After this process, the experimental results show an OMT working in the band from 13.4 to 15.6 GHz (15.2%) with a return loss level higher than 20 dB for both polarizations, insertion loss lower than 0.18 dB and isolation between polarizations better than 45 dB. The OMT has also been tested in radiation connected to a reference horn, measuring a cross-polarization lower than -45 dB. This experimental performance shows that the proposed combination of compact design with single-block SLM manufacturing provides tested results similar to those obtained by high-accuracy milling or spark erosion suitable for satellite applicationsThis work was supported by the Spanish Government under grant TEC2016-76070-C3-1/2-R (Agencia Estatal de Investigación, Fondo Europeo de Desarrollo Regional: AEI/FEDER, UE

Compact full ku-band triplexer with improved e-plane power divider

An improved E-plane power divider for compact waveguide triplexers with large separation between channels is presented. The configuration of the divider aims to exploit the different behavior of the device for frequency bands with large separation, leading to a very asymmetric E-plane junction. H-plane filters with inductive windows are used for each channel, in order to obtain reduced insertion losses and lower sensitivity than in metal-insert E-plane filters. The resultant triplexer configuration is very compact, and its design is analyzed and optimized by Mode-Matching. The experimental results of a full Ku-band prototype for communications satellite systems show a very good agreement with the expected simulated response

Rigorous analysis of the parallel plate waveguide: From the transverse electromagnetic mode to the surface plasmon polariton

This is the accepted version of the following article: K. S. Reichel, N. Sakoda, R. Mendis, D. M. Mittleman, Evanescent wave coupling in terahertz waveguide arrays, Optics Express, 2013, 21, 14, 17249, which has been published in final form at http://onlinelibrary.wiley.com/doi/10.1029/2011RS004838/fullThis paper presents an analysis of the parallel plate waveguide, based on a hybrid mode formulation. The nonideal metallic conductors of the waveguide are treated as a media characterized by an equivalent permittivity. The frequencies of interest in the presented analysis are at the terahertz band (from 300 GHz to 30 THz), and appropriate models are used for the correct characterization of metallic conductors at these frequencies. The behavior of the electromagnetic field of the fundamental mode is studied in a wide frequency range. At low frequencies (microwave regime) the fundamental mode is the well-known transverse electromagnetic (TEM) mode; as frequency increases, the electromagnetic field changes significantly and a surface wave or surface plasmon polariton (SPP) behavior is observed at the highest frequencies of the terahertz band. This paper shows a unified formulation that explains this transformation in the electromagnetic field behavior.This work has been partially supported by the Spanish government program TEC2010–17795, the CONSOLIDER CSD2008–00068, and a PhD grant from Universidad Politécnica de Madrid

Additive manufacturing of mode converters in Ku and Q bands by selective laser sintering: experience and results

In recent years, Additive Manufacturing (AM) has turned out as a disruptive technology [1]. Fast production, rapid prototyping or adaptability, are essential concepts in sectors such as automotive, aerospace, biotech, etc. [2], [3]. In microwave engineering, the main advantages of AM are the possibility to produce customized items and the complexity of the implemented geometries compared with other technologies such as Computer Numerical Control (CNC) machining, injection moulding, casting or Electrical Discharge Machining (EDM). Nowadays, AM technologies are focused on the development of the next generation of microwave and millimetrewave devices. Regarding high-frequency circuits, and more specifically in the case of waveguide technology devices, the impact has been very relevant [4]. The initial efforts have been focused on filters, couplers, feed components and antennas. However, in this work the experience and results with other sort of devices, i.e., the mode converters, will be exposed. These broadband devices without resonant behaviour and strong electromagnetic fields are especially well-suited to cope with the two main problems of AM, i.e., the manufacturing accuracy and the surface roughness. Two different mode converters have been designed and manufactured by means of Selective Laser Sintering technology using aluminium alloy powder. The first one is a TE10 rectangular mode to TM01 circular mode converter in Ku-band and the second one is a TE10 rectangular mode to TE01 circular mode flared-type converter in Q-band. The experimental results obtained in both cases will be presented in detail. In addition, the issues related to the orientation of the parts inside the building chamber and other undesirable effects such as spikes due to manufacturing asymmetries, will be shared with the scientific community

Siw 2D planar array with four cross slots radiator and tuning vias

A Substrate Integrated Waveguide (SIW) planar array is presented using a right handed circularly polarized (RHCP) element with four crossed tilted radiating slots. In addition, a pair of metallic tuning vias is included to really improve the reflection of longest slots. A corporate feeding network over SIW has been designed for distributing the input signal to 128 radiating elements, divided into 8 progressive wave linear arrays of 16 elements each. The designed planar array has been manufactured and measured to verify the antenna performance. 25.5 dB gain, 2.33 dB axial ratio, as well as 85% radiation efficiency values have been experimentally achieved at 17 GHz. A 3% usable bandwidth (16.75{17.25 GHz) is obtained due to the typical frequency main beam tilt dispersion in the elevation plane of the progressive wave arrays