23 research outputs found
Cooling Characteristics of a 2-Row Radial Engine
This report presents the results of cooling tests conducted on a calibrated GR-1535 Pratt and Whitney Wasp, Jr. Engine installed in a Vought X04U-2 airplane. The tests were made in the NACA full-scale tunnel at air speeds from 70 to 120 miles per hour, at engine speeds from 1,500 to 2,600 r.p.m., and at manifold pressures from 19 to 33 inches of mercury absolute. A Smith controllable propeller was used to facilitate obtaining the different combinations of engine speed, power, and manifold pressure
Air Flow Around Finned Cylinders
Report presents the results of a study made to determine the air-flow characteristics around finned cylinders. Air-flow distribution is given for a smooth cylinder, for a finned cylinder having several fin spacings and fin widths, and for a cylinder with several types of baffle with various entrance and exit shapes. The results of these tests show: that flow characteristics around a cylinder are not so critical to changes in fin width as they are to fin spacing; that the entrance of the baffle has a marked influence on its efficiency; that properly designed baffles increase the air flow over the rear of the cylinder; and that these tests check those of heat-transfer tests in the choice of the best baffle
The Effect of Baffles on the Temperature Distribution and Heat-transfer Coefficients of Finned Cylinders
This report presents the results of an investigation to determine the effect of baffles on the temperature distribution and the heat-transfer coefficient of finned cylinders. The tests were conducted in a 30-inch wind tunnel on electrically heated cylinders with fins of 0.25 and 0.31 inch pitch. The results of these tests showed that the use of integral baffles gave a reduction of 31.9 percent in the rear wall temperatures and an increase of 54.2 percent in the heat transfer coefficient as compared with a cylinder without baffles
Pressure Drop Across Finned Cylinders Enclosed in a Jacket
The pressure drop across finned cylinders in a jacket for a range of air speeds from approximately 13 to 230 miles per hour has been investigated. Tests were made to determine the effect on the pressure drop of changes in fin space, fin width, jacket entrance and exit areas, skirt-approach radius, and the use of fillets and a separator plate at the rear of the cylinder. The pressure drop across the cylinder increased as the fin space decreased, the increase being very rapid at fin spaces smaller than approximately 0.20 inch. Fin width had little effect on the pressure drop for the range of widths tested. The pressure drop across the cylinder was nearly halved by increasing the skirt-approach radius from 3/4 inch to 1-1/4 inches, but fillets and a separator plate at the rear of the cylinder had little effect on the pressure drop. The pressure drop across a cylinder with tapered fins was greater than that for a cylinder having rectangular fins with the same effective fin spacing
The Effect of Increased Carburetor Pressure on Engine Performance at Several Compression Ratios
The object of this investigation was to determine the effect of increasing the carburetor pressures from 30 to 40 inches of mercury, at compression ratios from 3.5 to 7.5, on the power, on the maximum cylinder pressures, on the fuel consumption, and on the other performance characteristics of an engine. A roots-type aircraft-engine supercharger was used to maintain the desired carburetor pressure
Icing-Protection Requirements for Reciprocating-Engine Induction System
Despite the development of relatively ice-free fuel-metering systems, the widespread use of alternate and heated-air intakes, and the use of alcohol for emergency de-icing, icing of aircraft-engine induction systems is a serious problem. Investigations have been made to study and to combat all phases of this icing problem. From these investigations, criterions for safe operation and for design of new induction systems have been established. The results were obtained from laboratory investigations of carburetor-supercharger combinations, wind-tunnel investigations of air scoops, multicylinder-engine studies, and flight investigations. Characteristics of three forms of ice, impact, throttling, and fuel evaporation were studied. The effects of several factors on the icing characteristics were also studied and included: (1) atmospheric conditions, (2) engine and air-scoop configurations, including light-airplane system, (3) type fuel used, and (4) operating variables, such as power condition, use of a manifold pressure regulator, mixture setting, carburetor heat, and water-alcohol injection. In addition, ice-detection methods were investigated and methods of preventing and removing induction-system ice were studied. Recommendations are given for design and operation with regard to induction-system design
Recommended from our members
NACA Memorandum Reports
Report discussing the results of accelerated erosion tests to determine the separate effects of the passage of fuel, water, and ice particles through a supercharger. Recommendations for preventing erosion are provided, including materials choice and joint design
Recommended from our members
NACA Technical Notes
Report presenting an experimental investigation in order to determine the effect of jet temperature on jet-noise generation. Jet pressure ratios from 1.3 to 1.9 and temperature from 80 to 1000 degrees Fahrenheit. Results showed that sound power can be adequately predicted by the Lighthill parameter based on ambient temperature over the range of temperatures investigated
Recommended from our members
NACA Technical Reports
This report presents the results of an investigation to determine the effect of baffles on the temperature distribution and the heat-transfer coefficient of finned cylinders. The tests were conducted in a 30-inch wind tunnel on electrically heated cylinders with fins of 0.25 and 0.31 inch pitch. The results of these tests showed that the use of integral baffles gave a reduction of 31.9 percent in the rear wall temperatures and an increase of 54.2 percent in the heat transfer coefficient as compared with a cylinder without baffles