A theoretical study of the acoustic impedance of orifices in the presence of a steady grazing flow

An analysis of the oscillatory fluid flow in the vicinity of a circular orifice with a steady grazing flow is presented. The study is similar to that of Hersh and Rogers but with the addition of the grazing flow. Starting from the momentum and continuity equations, a considerably simplified system of partial differential equations is developed with the assumption that the flow can be described by an oscillatory motion superimposed upon the known steady flow. The equations are seen to be linear in the region where the grazing flow effects are dominant, and a solution and the resulting orifice impedance are presented for this region. The nonlinearity appears to be unimportant for the usual conditions found in aircraft noise suppressors. Some preliminary conclusions of the study are that orifice resistance is directly proportional to grazing flow velocity (known previously from experimental data) and that the orifice inductive (mass reactance) end correction is not a function of grazing flow. This latter conclusion is contrary to the widely held notion that grazing flow removes the effect of the orifice inductive end correction. This conclusion also implies that the experimentally observed total inductance reduction with grazing flow might be in the flow within the orifice rather than in the end correction

Spinning mode sound propagation in ducts with acoustic treatment

A detailed theoretical study of the acoustic propagation of spinning modes in acoustically treated open circular ducts is described. The suppressor with splitter rings was modeled by using the rectangular approximation to the annular duct. The theoretical models were used to determine optimum impedance and maximum attenuation for several spinning lobe numbers from 0 to 50. Some interesting results of the analysis are that for circular ducts the maximum possible attenuation and the optimum wall impedance are strong functions of the lobe number. For annular ducts the attenuation and optimum wall impedance are insensitive to the spinning lobe number for well cut-on modes. The above results help explain why suppressors with splitter rings were quite effective in spite of the lack of detailed information on the noise source modal structure

Multimodal far-field acoustic radiation pattern: An approximate equation

The far-field sound radiation theory for a circular duct was studied for both single mode and multimodal inputs. The investigation was intended to develop a method to determine the acoustic power produced by turbofans as a function of mode cut-off ratio. With reasonable simplifying assumptions the single mode radiation pattern was shown to be reducible to a function of mode cut-off ratio only. With modal cut-off ratio as the dominant variable, multimodal radiation patterns can be reduced to a simple explicit expression. This approximate expression provides excellent agreement with an exact calculation of the sound radiation pattern using equal acoustic power per mode

Spinning mode sound propagation in ducts with acoustic treatment and sheared flow

The propagation of spinning mode sound was considered for a cylindrical duct with sheared steady flow. Calculations concentrated on the determination of the wall optimum acoustic impedance and the maximum possible attenuation. Both the least attenuated and higher radial modes for spinning lobe patterns were considered. A parametric study was conducted over a wide range of Mach numbers, spinning lobe numbers, sound frequency, and boundary layer thickness. A correlation equation was developed from theoretical considerations starting with the thin boundary layer approximation of Eversman. This correlation agrees well with the more exact calculations for inlets and provides a single boundary layer refraction parameter which determines the change in optimum wall impedance due to refraction effects

Modal propagation angles in ducts with soft walls and their connection with suppressor performance

The angles of propagation of the wave fronts associated with duct modes are derived for a cylindrical duct with soft walls (acoustic suppressors) and a uniform steady flow. The angle of propagation with respect to the radial coordinate (angle of incidence on the wall) is shown to be a better correlating parameter for the optimum wall impedance of spinning modes than the previously used mode cutoff ratio. Both the angle of incidence upon the duct wall and the propagation angle with respect to the duct axis are required to describe the attenuation of a propagating mode. Using the modal propagation angles, a geometric acoustics approach to suppressor acoustic performance was developed. Results from this approximate method were compared to exact modal propagation calculations to check the accuracy of the approximate method. The results are favorable except in the immediate vicinity of the modal optimum impedance where the approximate method yields about one-half of the exact maximum attenuation

Optimum wall impedance for spinning modes: A correlation with mode cut-off ratio

A correlating equation relating the optimum acoustic impedance for the wall lining of a circular duct to the acoustic mode cut-off ratio, is presented. The optimum impedance was correlated with cut-off ratio because the cut-off ratio appears to be the fundamental parameter governing the propagation of sound in the duct. Modes with similar cut-off ratios respond in a similar way to the acoustic liner. The correlation is a semi-empirical expression developed from an empirical modification of an equation originally derived from sound propagation theory in a thin boundary layer. This correlating equation represents a part of a simplified liner design method, based upon modal cut-off ratio, for multimodal noise propagation

Acoustic liner optimum impedance for spinning modes with cut-off ratio as the design criterion

A new acoustic liner design procedure based upon model cut-off ratio is outlined. Proposed experiments to substantiate this design procedure are outlined

Modal density function and number of propagating modes in ducts

The question of the number of propagating modes within a small range of mode cut off ratio was raised. The population density of modes were shown to be greatest near cut off and least for the well propagating modes. It was shown that modes of nearly the same cut off ratio behave nearly the same in a sound absorbing duct as well as in the way they propagate to the far. Handling all of the propagating modes individually, they can be grouped into several cut off ratio ranges. It is important to know the modal density function to estimate acoustic power distribution

Attenuation of sound in ducts with acoustic treatment: A generalized approximate equation

A generalized approximate equation for duct lining sound attenuation is presented. The specification of two parameters, the maximum possible attenuation and the optimum wall acoustic impedance is shown to completely determine the sound attenuation for any acoustic mode at any selected wall impedance. The equation is based on the nearly circular shape of the constant attenuation contours in the wall acoustic impedance plane. For impedances far from the optimum, the equation reduces to Morse's approximate expression. The equation can be used for initial acoustic liner design. Not least important is the illustrative nature of the solutions which provide an understanding of the duct propagation problem usually obscured in the exact calculations. Sample calculations using the approximate attenuation equation show that the peak and the bandwidth of the sound attenuation spectrum can be represented by quite simple functions of the ratio of actual wall acoustic resistance to optimum resistance

A model for the pressure excitation spectrum and acoustic impedance of sound absorbers in the presence of grazing flow

The acoustic impedance of sound absorbers in the presence of grazing flow is essential information when analyzing sound propagation within ducts. A unification of the theory of the nonlinear acoustic resistance of Helmholtz resonators including grazing flow is presented. The nonlinear resistance due to grazing flow is considered to be caused by an exciting pressure spectrum produced by the interaction of the grazing flow and the jets flowing from the resonator orifices. With this exciting pressure spectrum the resonator can be treated in the same manner as a resonator without grazing flow but with an exciting acoustic spectrum