High-temperature ''hydrostatic'' extrusion

Quasi-fluids permit hydrostatic extrusion of solid materials. The use of sodium chloride, calcium fluoride, or glasses as quasi-fluids reduces handling, corrosion, and sealing problems, these materials successfully extrude steel, molybdenum, ceramics, calcium carbonate, and calcium oxide. This technique also permits fluid-to-fluid extrusion

Loading and heating of a large flat plate at Mach 7 in the Langley 8-foot high-temperature structures tunnel

Surface pressure and cold-wall heating rate distributions (wall-temperature to total-temperature ratio approximately 0.2) were obtained on a large, flat calibration panel at a nominal Mach number of 7 in an 8-foot high-temperature structures tunnel. Panel dimensions were 42.5 by 60.0 in. Test objectives were: (1) to map available flat-plate loading and heating provided by the facility and (2) to determine effectiveness of leading-edge bluntness, boundary-layer trips, and aerodynamic fences in generating a uniform, streamwise turbulent flow field over the test surface of a flat-sided panel holder

Aerothermal tests of a 12.5 percent cone at Mach 6.7 for various Reynolds numbers, angles of attack and nose shapes

The effects of free-stream unit Reynolds number, angle of attack, and nose shape on the aerothermal environment of a 3-ft basediameter, 12.5 deg half-angle cone were investigated in the Langley 8-foot high temperature tunnel at Mach 6.7. The average total temperature was 3300 R, the freestream unit Reynolds number ranged from 400,000 to 1,400,000 per foot, and the angle of attack ranged from 0 deg to 10 deg. Three nose configurations were tested on the cone: a 3-in-radius tip, a 1-in-radius tip on an ogive frustum, and a sharp tip on an ogive frustum. Surface-pressure and cold-wall heating-rate distributions were obtained for laminar, transitional temperature in the shock layer were obtained. The location of the start of transition moved forward both on windward and leeward sides with increasing free-stream Reynolds numbers, increasing angle of attack, and decreasing nose bluntness

Multiparameter vision testing apparatus

Compact vision testing apparatus is described for testing a large number of physiological characteristics of the eyes and visual system of a human subject. The head of the subject is inserted into a viewing port at one end of a light-tight housing containing various optical assemblies. Visual acuity and other refractive characteristics and ocular muscle balance characteristics of the eyes of the subject are tested by means of a retractable phoroptor assembly carried near the viewing port and a film cassette unit carried in the rearward portion of the housing (the latter selectively providing a variety of different visual targets which are viewed through the optical system of the phoroptor assembly). The visual dark adaptation characteristics and absolute brightness threshold of the subject are tested by means of a projector assembly which selectively projects one or both of a variable intensity fixation target and a variable intensity adaptation test field onto a viewing screen located near the top of the housing

Investigation of real-gas and viscous effects on the aerodynamic characteristics of a 40 deg half-cone with suggested correlations for the shuttle orbiter

Parameters were evaluated that might be used to correlate shuttle orbiter aerodynamic data to be used in extrapolating from wind-tunnel to flight conditions. Preliminary calculations indicate that the lee-side forces will have an insignificant influence on the aerodynamic characteristics of the orbiter for moderate angle-of-attack entries; therefore, this work is focused on phenomena which have an overriding influence on windward forces, namely, real-gas (equilibrium and nonequilibrium) and viscous-interaction effects. Analytically determined flow fields previously obtained on 40 deg blunted cones were used as a data source to evaluate various correlation parameters. Inviscid effects were found to be the dominant contributor to the aerodynamic coefficients in the altitude range of 64 to 76.2 km. The most suitable correlation of the aerodynamic forces on these cones is based on local dynamic pressure and local Mach number

Driving forces in free visual search : An ethology

Peer reviewedPostprin

Noise sustained propagation: Local versus global noise

We expand on prior results on noise supported signal propagation in arrays of coupled bistable elements. We present and compare experimental and numerical results for kink propagation under the influence of local and global fluctuations. As demonstrated previously for local noise, an optimum range of global noise power exists for which the medium acts as a reliable transmission ``channel''. We discuss implications for propagation failure in a model of cardiac tissue and present a general theoretical framework based on discrete kink statistics. Valid for generic bistable chains, the theory captures the essential features ob served in our experiments and numerical simulations.Comment: 1 latex file 20 pages, 9 figures. Accepted for publication in Physical Review

Evaluation of a composite mobile holographic nondestructive test system

A simplified theoretical model for the interpretation of the double-exposure holographic interference fringe loci due to the general three-dimensional displacements was derived for the specific composite mobile holographic nondestructive test system. The model, representing a good approximation to a more tedious theoretical result, predicts that a combination of in-plane and out-of-plane displacements of the surface will produce concentric circular-shaped fringe patterns with locations of their center affected by the displacements. Appropriate experiments were designed and carried out for the test of the validity of the theory. These experiments include the taking of double-exposure holograms of in-plane translations and combined in-plane and out-of-plane translations. The simplified model agreed quite well with the experimental results. Experimentally observed effects due to the curvature of the test plate and the variations of the angles of incidence of the laser light suggest that in order for the simplified model to be able to predict the test results more accurately, incidence and reflection of the laser light should be chosen as nearly perpendicular to the surface of the tested object as possible