Topologically Protected Loop Flows in High Voltage AC Power Grids

Geographical features such as mountain ranges or big lakes and inland seas often result in large closed loops in high voltage AC power grids. Sizable circulating power flows have been recorded around such loops, which take up transmission line capacity and dissipate but do not deliver electric power. Power flows in high voltage AC transmission grids are dominantly governed by voltage angle differences between connected buses, much in the same way as Josephson currents depend on phase differences between tunnel-coupled superconductors. From this previously overlooked similarity we argue here that circulating power flows in AC power grids are analogous to supercurrents flowing in superconducting rings and in rings of Josephson junctions. We investigate how circulating power flows can be created and how they behave in the presence of ohmic dissipation. We show how changing operating conditions may generate them, how significantly more power is ohmically dissipated in their presence and how they are topologically protected, even in the presence of dissipation, so that they persist when operating conditions are returned to their original values. We identify three mechanisms for creating circulating power flows, (i) by loss of stability of the equilibrium state carrying no circulating loop flow, (ii) by tripping of a line traversing a large loop in the network and (iii) by reclosing a loop that tripped or was open earlier. Because voltage angles are uniquely defined, circulating power flows can take on only discrete values, much in the same way as circulation around vortices is quantized in superfluids.Comment: 12 pages 6 figures + Supplementary Material, Accepted for publication in New Journal of Physic

Friction pull plug welding: top hat plug design

Friction Pull Plug Welding is a solid state repair process for defects up to one inch in length, only requiring single sided tooling, or outside skin line (OSL), for preferred usage on flight hardware. The most prevalent defect associated with Friction Pull Plug Welding (FPPW) was a top side or inside skin line (ISL) lack of bonding. Bonding was not achieved at this location due to the reduction in both frictional heat and welding pressure between the plug and plate at the end of the weld. Thus, in order to eliminate the weld defects and increase the plug strength at the plug `top` a small `hat` section is added to the pull plug for added frictional heating and pressure

Friction pull plug welding: chamfered heat sink pull plug design

The average strength of a pull plug weld is increased and weak bonding eliminated by providing a dual included angle at the top one third of the pull plug. Plugs using the included angle of the present invention had consistent high strength, no weak bonds and were substantially defect free. The dual angle of the pull plug body increases the heat and pressure of the weld in the region of the top one third of the plug. This allows the plug to form a tight high quality solid state bond. The dual angle was found to be successful in elimination of defects on both small and large plugs

Friction pull plug welding: chamfered heat sink pull plug design

Friction Pull Plug Welding (FPPW) is a solid state repair process for defects up to one inch in length, only requiring single sided tooling (OSL) for usage on flight hardware. Experimental data has shown that the mass of plug heat sink remaining above the top of the plate surface after a weld is completed (the plug heat sink) affects the bonding at the plug top. A minimized heat sink ensures complete bonding of the plug to the plate at the plug top. However, with a minimal heat sink three major problems can arise, the entire plug could be pulled through the plate hole, the central portion of the plug could be separated along grain boundaries, or the plug top hat can be separated from the body. The Chamfered Heat Sink Pull Plug Design allows for complete bonding along the ISL interface through an outside diameter minimal mass heat sink, while maintaining enough central mass in the plug to prevent plug pull through, central separation, and plug top hat separation

Friction pull plug welding: dual chamfered plate hole

Friction Pull Plug Welding (FPPW) is a solid state repair process for defects up to one inch in length, only requiring single sided tooling (OSL) for usage on flight hardware. Early attempts with FPPW followed the matching plug/plate geometry precedence of the successful Friction Push Plug Welding program, however no defect free welds were achieved due to substantial plug necking and plug rotational stalling. The dual chamfered hole has eliminated plug rotational stalling, both upon initial plug/plate contact and during welding. Also, the necking of the heated plug metal under a tensile heating/forging load has been eliminated through the usage of the dual chamfered plate hole

Evidence of columnar order in the fully frustrated transverse field Ising model on the square lattice

Using extensive classical and quantum Monte Carlo simulations, we investigate the ground-state phase diagram of the fully frustrated transverse field Ising model on the square lattice. We show that pure columnar order develops in the low-field phase above a surprisingly large length scale, below which an effective U(1) symmetry is present. The same conclusion applies to the Quantum Dimer Model with purely kinetic energy, to which the model reduces in the zero-field limit, as well as to the stacked classical version of the model. By contrast, the 2D classical version of the model is shown to develop plaquette order. Semiclassical arguments show that the transition from plaquette to columnar order is a consequence of quantum fluctuations.Comment: 5 pages (including Supplemental Material), 5 figure

Current surgical concepts and indications in the management of the short bowel state: A call for the use of multidisciplinary intestinal rehabilitation programs

The mainstay of management for short bowel syndrome (SBS) is to promote access to the best quality of care provided by the intestinal rehabilitation program (IRP) in specialized centres. When treating SBS patients, the main goal is to minimize disease-associated complications, as well as achieve enteral autonomy. Surgical strategies should be selected cautiously upon the actual state of the bowel with respect to what it is clinically relevant for that specific patient. To this aim, a personalized and multidisciplinary approach for such a complex syndrome is needed

Cardiolipin drives cytochrome c proapoptotic and antiapoptotic actions

""\\"Cytochrome c (cytc) is pivotal in mitochondrial respiration and apoptosis. The heme-Fe-atom of native hexacoordinated horse heart cytc (hhcytc) displays a very low reactivity toward ligands and does not exhibit catalytic properties. However, on interaction with cardiolipin (CL), hhcytc changes its tertiary structure disrupting the heme-Fe-Met80 distal bond. The CL-hhcytc complex displays a very low midpoint potential, out of the range required for its physiological role, binds CO and NO with high affinity, facilitates peroxynitrite isomerization to NO(3)(-), and displays peroxidase activity. As a whole, the CL-hhcytc complex could play either proapoptotic effects, catalyzing lipid peroxidation and the subsequent hhcytc release into the cytoplasm, or antiapoptotic actions, such as scavenging peroxynitrite (i.e., protecting the mitochondrion from reactive nitrogen and oxygen species), and binding of CO and NO (i.e., inhibiting lipid peroxidation and hhcytc traslocation). Here, the CL-driven allosteric modulation of hhcytc properties is reviewed, highlighting proapoptotic and antiapoptotic actions. (C) 2011 IUBMB IUBMB Life, 63(3): 160-165, 2011\\""