Boundary layer control for airships

An investigation is summarized of the aerodynamic principle of boundary layer control for nonrigid LTA craft. The project included a wind tunnel test on a BLC body of revolution at zero angle of attack. Theoretical analysis is shown to be in excellent agreement with the test data. Methods are evolved for predicting the boundary layer development on a body of revolution and the suction pumping and propulsive power requirements. These methods are used to predict the performance characteristics of a full-scale airship. The analysis indicates that propulsive power reductions of 15 to 25 percent and endurance improvements of 20 to 40 percent may be realized in employing boundary-layer control to nonrigid airships

Assessing climate model software quality: a defect density analysis of three models

A climate model is an executable theory of the climate; the model encapsulates climatological theories in software so that they can be simulated and their implications investigated. Thus, in order to trust a climate model, one must trust that the software it is built from is built correctly. Our study explores the nature of software quality in the context of climate modelling. We performed an analysis of defect reports and defect fixes in several versions of leading global climate models by collecting defect data from bug tracking systems and version control repository comments. We found that the climate models all have very low defect densities compared to well-known, similarly sized open-source projects. We discuss the implications of our findings for the assessment of climate model software trustworthiness

Steady State Performance of Spark Ignition Engine with Exhaust Energy Recovery

As is known, internal combustion engines based on Otto or Diesel cycles cannot complete the expansion process of the gas inside the cylinder, thus losing a relevant energy content, in the order of 30% of total. The residual energy of the unexpanded gas has been partially exploited through the use of an exhaust gas turbine for turbocharging the internal combustion engine; further attempts have been made with several compound solutions, with an electric generator connected to the turbocharger allowing to convert into electrical energy the quota power produced by the turbine which is not used by the compressor, or with a second turbine downstream the first to increase the exhaust gas energy recovery. Turbo-compound solutions were also employed in large marine Diesel engines, where the second turbine downstream the first was used to deliver more power to the main propeller shaft. In all these cases the overall efficiency increments remained within 5%. If completely recovered by the use of a properly designed expander-generator unit, the energy content of the unexpanded in-cylinder gas could substantially increase the overall efficiency of the thermal unit. In the present paper the authors evaluate, by means of simple yet effective calculations, the efficiency attainable by a thermal unit composed of a spark ignition engine endowed of an exhaust gas energy recovery expander connected to a proper generator. The proposed thermal unit, which is particularly suitable for hybrid propulsion solutions, has been evaluated both in the naturally aspirated and in the supercharged version. The efficiency of each thermal unit is also compared to reference baseline engine, thus highlighting the real benefit introduced by the adoption of the proposed thermal unit. As result, it was found that the complete and efficient recovery of the unexpanded gas energy has the potential to increase the overall efficiency of the propulsion system by 10-15%, depending on the characteristics of the thermal engine and of the exhaust energy expander-generator unit

A life cycle environmental impact comparison between traditional, hybrid, and electric vehicles in the european context

Global warming (GW) and urban pollution focused a great interest on hybrid electric vehicles (HEVs) and battery electric vehicles (BEVs) as cleaner alternatives to traditional internal combustion engine vehicles (ICEVs). The environmental impact related to the use of both ICEV and HEV mainly depends on the fossil fuel used by the thermal engines, while, in the case of the BEV, depends on the energy sources employed to produce electricity. Moreover, the production phase of each vehicle may also have a relevant environmental impact, due to the manufacturing processes and the materials employed. Starting from these considerations, the authors carried out a fair comparison of the environmental impact generated by three different vehicles characterized by different pro-pulsion technology, i.e., an ICEV, an HEV, and a BEV, following the life cycle analysis methodology, i.e., taking into account five different environmental impact categories generated during all phases of the entire life of the vehicles, from raw material collection and parts production, to vehicle assembly and on\u2010road use, finishing hence with the disposal phase. An extensive scenario analysis was also performed considering different electricity mixes and vehicle lifetime mileages. The results of this study confirmed the importance of the life cycle approach for the correct determination of the real impact related to the use of passenger cars and showed that the GW impact of a BEV during its entire life amounts to roughly 60% of an equivalent ICEV, while acidifying emissions and par-ticulate matter were doubled. The HEV confirmed an excellent alternative to ICEV, showing good compromise between GW impact (85% with respect to the ICEV), terrestrial acidification, and par-ticulate formation (similar to the ICEV). In regard to the mineral source deployment, a serious concern derives from the lithium\u2010ion battery production for BEV. The results of the scenario analysis highlight how the environmental impact of a BEV may be altered by the lifetime mileage of the vehicle, and how the carbon footprint of the electricity used may nullify the ecological advantage of the BEV

Analysis of the Combustion Process in a Hydrogen-Fueled CFR Engine

Green hydrogen, produced using renewable energy, is nowadays one of the most promising alternatives to fossil fuels for reducing pollutant emissions and in turn global warming. In particular, the use of hydrogen as fuel for internal combustion engines has been widely analyzed over the past few years. In this paper, the authors show the results of some experimental tests performed on a hydrogen-fueled CFR (Cooperative Fuel Research) engine, with particular reference to the combustion. Both the air/fuel (A/F) ratio and the engine compression ratio (CR) were varied in order to evaluate the influence of the two parameters on the combustion process. The combustion duration was divided in two parts: the flame front development (characterized by laminar flame speed) and the rapid combustion phase (characterized by turbulent flame speed). The results of the hydrogen-fueled engine have been compared with results obtained with gasoline in a reference operating condition. The increase in engine CR reduces the combustion duration whereas the opposite effect is observed with an increase in the A/F ratio. It is interesting to observe how the two parameters, CR and A/F ratio, have a different influence on the laminar and turbulent combustion phases. The influence of both A/F ratio and engine CR on heat transfer to the combustion chamber wall was also evaluated and compared with the gasoline operation. The heat transfer resulting from hydrogen combustion was found to be higher than the heat transfer resulting from gasoline combustion, and this is probably due to the different quenching distance of the two fuels

Hybrid Propulsion Efficiency Increment through Exhaust Energy Recovery—Part 1: Radial Turbine Modelling and Design

The efficiency of Hybrid Electric Vehicles (HEVs) may be substantially increased if the energy of the exhaust gases, which do not complete the expansion inside the cylinder of the internal combustion engine, is efficiently recovered by means of a properly designed turbogenerator and employed for vehicle propulsion; previous studies, carried out by the same authors of this work, showed a potential hybrid vehicle fuel efficiency increment up to 15% by employing a 20 kW turbine on a 100 HP rated power thermal unit. The innovative thermal unit here proposed is composed of a supercharged engine endowed with a properly designed turbogenerator, which comprises two fundamental elements: an exhaust gas turbine expressly designed and optimized for the application, and a suitable electric generator necessary to convert the recovered energy into electric energy, which can be stored in the on-board energy storage system of the vehicle. In these two parts, the realistic efficiency of the innovative thermal unit for hybrid vehicle is evaluated and compared to a traditional turbocharged engine. In Part 1, the authors present a model for the prediction of the efficiency of a dedicated radial turbine, based on a simple but effective mean-line approach; the same paper also reports a design algorithm, which, owing to some assumptions and approximations, allows a fast determination of the proper turbine geometry for a given design operating condition. It is worth pointing out that, being optimized for quasi-steady power production, the exhaust gas turbine considered is quite different from the ones commonly employed for turbocharging application; for this reason, and in consideration of the required power size, such a turbine is not available on the market, nor has its development been previously carried out in the scientific literature. In the Part 2 paper, a radial turbine geometry is defined for the thermal unit previously calculated, employing the design algorithm described in Part 1; the realistic energetic advantage that could be achieved by the implementation of the turbogenerator on a hybrid propulsion system is evaluated through the performance prediction model under the different operating conditions of the thermal unit. As an overall result, it was estimated that, compared to a reference traditional turbocharged engine, the turbocompound system could gain vehicle efficiency improvement between 3.1% and 17.9%, depending on the output power level, while an average efficiency increment of 10.9% was determined for the whole operating range

A semi-automatic system for labelling seafood products and obtaining fishery management data: A case study of the bottom trawl fishery in the central Mediterranean Sea

This study is on the implementation of a semi-automatic labelling system (LS) of the Mediterranean Sea seafood harvest to address the increased need for seafood authentication and inherent difficulties of commonly used indirect techniques for estimating fisheries yield and fishing effort. Sensitive datarequired for anti-counterfeit policies, such as date and catch area, can be acquired and recorded on the label by user-friendly automated software that excludes any possible manipulation by the crew. Based on results obtained from the installation of the LS on bottom commercial trawlers, the system certified the origin of the seafood products and simultaneously provided, indirectly, geospatial fisheries yield and fishing effort data of the main exploited species