114 research outputs found
Automated Method for the Determination of 5′-Nucleotidase in Serum by Continuous Flow Analysis
Peer Reviewe
Continuous wave optical parametric oscillator for quartz-enhanced photoacoustic trace gas sensing
A continuous wave optical parametric oscillator, generating up to 300 mW idler output in the 3–4 μm wavelength region, and pumped by a fiber-amplified DBR diode laser is used for trace gas detection by means of quartz-enhanced photoacoustic spectroscopy (QEPAS). Mode-hop-free tuning of the OPO output over 5.2 cm-1 and continuous spectral coverage exceeding 16.5 cm-1 were achieved via electronic pump source tuning alone. Online monitoring of the idler wavelength, with feedback to the DBR diode laser, provided an automated closed-loop control allowing arbitrary idler wavelength selection within the pump tuning range and locking of the idler wavelength with a stability of 1.7×10-3 cm-1 over at least 30 min.\ud
\ud
Using this approach, we locked the idler wavelength at an ethane absorption peak and obtained QEPAS data to verify the linear response of the QEPAS signal at different ethane concentrations (100 ppbv-20 ppmv) and different power levels. The detection limit for ethane was determined to be 13 ppbv (20 s averaging), corresponding to a normalized noise equivalent absorption coefficient of 4.4×10-7 cm-1  W/Hz1/2
Characterization and correction of stray light in TROPOMI-SWIR
The shortwave infrared (SWIR) spectrometer module of the Tropospheric
Monitoring Instrument (TROPOMI), on board the ESA Copernicus Sentinel-5
Precursor satellite, is used to measure atmospheric CO and methane columns.
For this purpose, calibrated radiance measurements are needed that are
minimally contaminated by instrumental stray light. Therefore, a method has
been developed and applied in an on-ground calibration campaign to
characterize stray light in detail using a monochromatic quasi-point light
source. The dynamic range of the signal was extended to more than 7Â orders of magnitude by performing measurements with different exposure times,
saturating detector pixels at the longer exposure times. Analysis of the
stray light indicates about 4.4 % of the detected light is correctable stray
light. An algorithm was then devised and implemented in the operational data
processor to correct in-flight SWIR observations in near-real time, based on
Van Cittert deconvolution. The stray light is approximated by a far-field
kernel independent of position and wavelength and an additional kernel
representing the main reflection. Applying this correction significantly
reduces the stray-light signal, for example in a simulated dark forest scene
close to bright clouds by a factor of about 10. Simulations indicate that
this reduces the stray-light error sufficiently for accurate gas-column
retrievals. In addition, the instrument contains five SWIR diode lasers that
enable long-term, in-flight monitoring of the stray-light distribution.</p
CCQM-K90, formaldehyde in nitrogen, 2 μmol mol− 1 Final report
The CCQM-K90 comparison is designed to evaluate the level of comparability of national metrology institutes (NMI) or designated institutes (DI) measurement capabilities for formaldehyde in nitrogen at a nominal mole fraction of 2 μmol mol−1.
The comparison was organised by the BIPM using a suite of gas mixtures prepared by a producer of specialty calibration gases. The BIPM assigned the formaldehyde mole fraction in the mixtures by comparison with primary mixtures generated dynamically by permeation coupled with continuous weighing in a magnetic suspension balance. The BIPM developed two dynamic sources of formaldehyde in nitrogen that provide two independent values of the formaldehyde mole fraction: the first one based on diffusion of trioxane followed by thermal conversion to formaldehyde, the second one based on permeation of formaldehyde from paraformaldehyde contained in a permeation tube.
Two independent analytical methods, based on cavity ring down spectroscopy (CRDS) and Fourier transform infrared spectroscopy (FTIR) were used for the assignment procedure.
Each participating institute was provided with one transfer standard and value assigned the formaldehyde mole fraction in the standard based on its own measurement capabilities.
The stability of the formaldehyde mole fraction in transfer standards was deduced from repeated measurements performed at the BIPM before and after measurements performed at participating institutes. In addition, 5 control standards were kept at the BIPM for regular measurements during the course of the comparison.
Temporal trends that approximately describe the linear decrease of the amount-of-substance fraction of formaldehyde in nitrogen in the transfer standards over time were estimated by two different mathematical treatments, the outcomes of which were proposed to participants. The two treatments also differed in the way measurement uncertainties arising from measurements performed at the BIPM were propagated to the uncertainty of the trend parameters, as well as how the dispersion of the dates when measurements were made by the participants was taken into account.
Upon decision of the participants, the Key Comparison Reference Values were assigned by the BIPM using the largest uncertainty for measurements performed at the BIPM, linear regression without weight to calculate the trend parameters, and not taking into account the dispersion of dates for measurements made by the participant. Each transfer standard was assigned its own reference value and associated expanded uncertainty. An expression for the degree of equivalence between each participating institute and the KCRV was calculated from the comparison results and measurement uncertainties submitted by participating laboratories. Results of the alternative mathematical treatment are presented in annex of this report
Determination of the TROPOMI-SWIR instrument spectral response function
The Tropospheric Monitoring Instrument (TROPOMI) is the single instrument on
board the ESA Copernicus Sentinel-5 Precursor satellite. TROPOMI is a
nadir-viewing imaging spectrometer with bands in the ultraviolet and visible,
the near infrared and the shortwave infrared (SWIR). An accurate instrument
spectral response function (ISRF) is required in the SWIR band where
absorption lines of CO, methane and water vapor overlap. In this paper, we
report on the determination of the TROPOMI-SWIR ISRF during an extensive
on-ground calibration campaign. Measurements are taken with a monochromatic
light source scanning the whole detector, using the spectrometer itself to
determine the light intensity and wavelength. The accuracy of the resulting
ISRF calibration key data is well within the requirement for trace-gas
retrievals. Long-term in-flight monitoring of SWIR ISRF is achieved using
five on-board diode lasers.</p
- …