Insulation system Patent

Light weight plastic foam thermal insulation for cryogenic storag

Aerocrane: A hybrid LTA aircraft for aerial crane applications

The Aerocrane, a hybrid aircraft, combines rotor lift with buoyant lift to offer VTOL load capability greatly in excess of helicopter technology while eliminating the airship problem of ballast transfer. In addition, the Aerocrane concept sharply reduces the mooring problem of airships and provides 360 deg vectorable thrust to supply a relatively large force component for control of gust loads. Designed for use in short range, ultra heavy lift missions, the Aerocrane operates in a performance envelope unsuitable for either helicopters or airships. Basic design considerations and potential problem areas of the concept are addressed

A Flight Evaluation and Analysis of the Effect of Icing Conditions on the ZPG-2 Airship

A series of test flights was conducted by the U. S. Navy over a 3- year period to evaluate the effects of icing on the operation of the ZPG-2 airship. In supercooled. clouds, ice formed only on the forward edges of small protuberances and wires and presented no serious hazard to operation. Ice accretions of the glaze type which occurred in conditions described as freezing drizzle adversely affected various components to a somewhat greater extent. The results indicated, a need for protection of certain components such as antennas, propellers, and certain parts of the control system. The tests showed that icing of the large surface of the envelope occurred only in freezing rain or drizzle. Because of the infrequent occurrence of these conditions, the potential maximum severity could not be estimated from the test results. The increases in heaviness caused by icing in freezing rain and drizzle were substantial, but well within the operational capabilities of the airship. In order to estimate the potential operational significance of icing in freezing rain, theoretical calculations were used to estimate: (1) the rate of icing as a function of temperature and rainfall intensity, (2) the climatological probability of occurrence of various combinations of these variables, and (3) the significance of the warming influence of the ocean in alleviating freezing-rain conditions. The results of these calculations suggest that, although very heavy icing rates are possible in combinations of low temperature and high rainfall rate, the occurrence of such conditions is very infrequent in coastal areas and virtually impossible 200 or 300 miles offshore

A correlation method to predict the surface pressure distribution on an infinite plate from which a jet is issuing

A correlation method to predict pressures induced on an infinite plate by a jet issuing from the plate into a subsonic free stream was developed. The complete method consists of an analytical method which models the blockage and entrainment properties of the jet and a correlation which accounts for the effects of separation. The method was developed for jet velocity ratios up to ten and for radial distances up to five diameters from the jet. Correlation curves and data comparisons are presented for jets issuing normally from a flat plate with velocity ratios one to twelve. Also, a list of references which deal with jets in a crossflow is presented

Prediction of vortex shedding from circular and noncircular bodies in supersonic flow

An engineering prediction method and associated computer code NOZVTX to predict nose vortex shedding from circular and noncircular bodies in supersonic flow at angles of attack and roll are presented. The body is represented by either a supersonic panel method for noncircular cross sections or line sources and doublets for circular cross sections, and the lee side vortex wake is modeled by discrete vortices in crossflow planes. The three-dimensional steady flow problem is reduced to a two-dimensional, unsteady, separated flow problem for solution. Comparison of measured and predicted surface pressure distributions, flow field surveys, and aerodynamic characteristics is presented for bodies with circular and noncircular cross-sectional shapes

An Electric Thrust Meter Suitable for Flight Investigation of Propellers

A lightweight instrument that utilizes resistance-wire electric strain gases to measure propeller-shaft thrust has been developed. A wind-tunnel investigation on a propeller installed, on a single-engine pursuit airplane showed that the instrument gave a reliable indication of propeller-shaft thrust to an accuracy of +/-2 percent within its calibrated range. No attempt was made to determine the relation of indicated shaft thrust to net propeller thrust

Computer programs to predict induced effects of jets exhausting into a crossflow

A user's manual for two computer programs was developed to predict the induced effects of jets exhausting into a crossflow. Program JETPLT predicts pressures induced on an infinite flat plate by a jet exhausting at angles to the plate and Program JETBOD, in conjunction with a panel code, predicts pressures induced on a body of revolution by a jet exhausting normal to the surface. Both codes use a potential model of the jet and adjacent surface with empirical corrections for the viscous or nonpotential effects. This program manual contains a description of the use of both programs, instructions for preparation of input, descriptions of the output, limitations of the codes, and sample cases. In addition, procedures to extend both codes to include additional empirical correlations are described

Why did the pheasant cross the road? Long-term road mortality patterns in relation to management changes.

This is the final version of the article. Available from Royal Society via the DOI in this record.Pheasants (Phasianus colchicus) are commonly killed on UK roads, presenting a threat to motorists and a loss to the game shooting industry. Pheasants may be inherently susceptible, or the recent increase in their artificial rearing and release may have exacerbated the situation, either through population increases or because artificial rearing has altered movement behaviour. We compared intra-annual patterns of roadkill reported in the UK from the 1960s (prior to the onset of mass release programmes) with that from the 2010s (when pheasant release was well established and widespread), considering roadkill sex and locations and accounting for changes in traffic levels. Pheasants in the UK are disproportionately likely to be reported killed on roads. However, this likelihood has not changed notably over the past 50 years. Instead, the timing of roadkill has changed. Pheasants in the 2010s are no longer susceptible during their breeding season, unlike in the 1960s, perhaps because relatively few breed successfully. Instead, roadkill first peaks in September-November as pheasants disperse from release pens, females first. Roadkill declines over winter, but when supplementary feeding ceases in February, we see a second peak in roadkill. Roadkill rates are higher in regions of the UK where there is little arable farming and hence natural food supplies are scarce.J.R.M. was funded by an ERC grant no. 616474

Assessment of the potential of solar thermal small power systems in small utilities

The potential economic benefit of small solar thermal electric power systems to small municipal and rural electric utilities is assessed. Five different solar thermal small power system configurations were considered in three different solar thermal technologies. The configurations included: (1) 1 MW, 2 MW, and 10 MW parabolic dish concentrators with a 15 kW heat engine mounted at the focal point of each dish, these systems utilized advanced battery energy storage; (2) a 10 MW system with variable slat concentrators and central steam Rankine energy conversion, this system utilized sensible thermal energy storage; and (3) a 50 MW central receiver system consisting of a field of heliostats concentrating energy on a tower-mounted receiver and a central steam Rankine conversion system, this system also utilized sensible thermal storage. The results are summarized in terms of break-even capital costs. The break-even capital cost was defined as the solar thermal plant capital cost which would have to be achieved in order for the solar thermal plants to penetrate 10 percent of the reference small utility generation mix by the year 2000. The calculated break-even capital costs are presented