Summary of Discussion Question 4: Energy Expandability of a Linear Collider

We report on Discussion Question 4, in Sub-group 1 (`TeV-class') of the Snowmass Working Group E3: `Experimental Approaches: Linear Colliders', which addresses the energy expandability of a linear collider. We first synthesize discussions of the energy reach of the hardware of the 500 GeV designs for TESLA and NLC/JLC. Next, we review plans for increasing the energy to 800-1000 GeV. We then look at options for expanding the energies to 1500 GeV and sketch the two-beam accelerator approach to achieving multi-TeV energies.Comment: Presented at Snowmass 2001 (6 pages, 2 figures

A new measurement of the cosmic ray energy spectrum between 3 x 10 to the 15th power eV and 3 x 10 to the 16th power eV

A new Cerenkov photon density spectrum measurement is reported. The derivation of the primary cosmic ray energy spectrum for energies from 3x10 to the 15th power eV to 3x10 to the 16th power eV are presented

A 5-kW xenon ion thruster lifetest

The results of the first life test of a high power ring-cusp ion thruster are presented. A 30-cm laboratory model thruster was operated steady-state at a nominal beam power of 5 kW on xenon propellant for approximately 900 hours. This test was conducted to identify life-timing erosion modifications, and to demonstrate operation using simplified power processing. The results from this test are described including the conclusions derived from extensive post-test analyses of the thruster. Modifications to the thruster and ground support equipment, which were incorporated to solve problems identified by the lifetest, are also described

Microanalysis of extended-test xenon hollow cathodes

Four hollow cathode electron sources were analyzed via boroscopy, scanning electron microscopy, energy dispersive x ray analysis, and x ray diffraction analysis. These techniques were used to develop a preliminary understanding of the chemistry of the devices that arise from contamination due to inadequate feed-system integrity and improper insert activation. Two hollow cathodes were operated in an ion thruster simulator at an emission current of 23.0 A for approximately 500 hrs. The two tests differed in propellant-feed systems, discharge power supplies, and activation procedures. Tungsten deposition and barium tungstate formation on the internal cathode surfaces occurred during the first test, which were believed to result from oxygen contamination of the propellant feed-system. Consequently, the test facility was upgraded to reduce contamination, and the test was repeated. The second hollow cathode was found to have experienced significantly less tungsten deposition. A second pair of cathodes examined were the discharge and the neutralizer hollow cathodes used in a life-test of a 30-cm ring-cusp ion thruster at a 5.5 kW power level. The cathodes' test history was documented and the post-test microanalyses are described. The most significant change resulting from the life-test was substantial tungsten deposition on the internal cathode surfaces, as well as removal of material from the insert surface. In addition, barium tungstate and molybdate were found on insert surfaces. As a result of the cathode examinations, procedures and approaches were proposed for improved discharge ignition and cathode longevity

Analysis of Cerenkov pulses recorded simultaneously at two sites

The agreement between measured distances to maximum for approx. 49 simultaneous Cerenkov pulse profiles from different sites is + or - approx. 0.1 km near 4.5 km and + or - 0.5 km near 7 km. Uncertainty in depths of maximum are approx. + or - 10 g sq and + or - 30 g cm/2 respectively. Usually the Hillas-Patterson simulation is able to fit both pulse shapes satisfactorily using a single N(x) profile

Process characteristics and design methods for a 300 deg quad OP amp

The results of process characterization, circuit design, and reliability studies for the development of a quad OP amplifier intended for use up to 300 C are presented. A dielectrically isolated complementary vertical bipolar process was chosen to fabricate the amplifier in order to eliminate isolation leakage and the possibility of latch up. Characterization of NPN and PNP junctions showed them to be suitable for use up to 300 C. Interconnect reliability was predicted to be greater than four years mean time between failure. Parasitic MOS formation was eliminated by isolation of each device

A study of parameter identification

A set of definitions for deterministic parameter identification ability were proposed. Deterministic parameter identificability properties are presented based on four system characteristics: direct parameter recoverability, properties of the system transfer function, properties of output distinguishability, and uniqueness properties of a quadratic cost functional. Stochastic parameter identifiability was defined in terms of the existence of an estimation sequence for the unknown parameters which is consistent in probability. Stochastic parameter identifiability properties are presented based on the following characteristics: convergence properties of the maximum likelihood estimate, properties of the joint probability density functions of the observations, and properties of the information matrix

The Effects of Auditor Tenure on Fraud and Its Detection

We examine the strategic effects of auditor tenure on the auditor's testing strategy and the manager's inclination to commit fraud. Most empirical studies conclude that longer tenure improves audit quality. Proponents of restricting tenure argue that longer tenure impairs auditor independence and a "fresh look" from a new auditor results in higher audit quality. Validating this argument requires testing whether the observed difference in audit quality between a continuing auditor and a change in auditors is less than the theoretically expected difference in audit quality without impairment. Our findings provide the guidance necessary for developing such tests. Our results show that audit risk (the probability that fraud exists and goes undetected) is lower in both periods for the continuing auditor than with a change in auditors. More importantly, we show that across both periods, expected undetected fraud is lower for the continuing auditor than with a change in auditors

Analytical and experimental studies of an optimum multisegment phased liner noise suppression concept

Results are presented from detailed analytical studies made to define methods for obtaining improved multisegment lining performance by taking advantage of relative placement of each lining segment. Properly phased liner segments reflect and spatially redistribute the incident acoustic energy and thus provide additional attenuation. A mathematical model was developed for rectangular ducts with uniform mean flow. Segmented acoustic fields were represented by duct eigenfunction expansions, and mode-matching was used to ensure continuity of the total field. Parametric studies were performed to identify attenuation mechanisms and define preliminary liner configurations. An optimization procedure was used to determine optimum liner impedance values for a given total lining length, Mach number, and incident modal distribution. Optimal segmented liners are presented and it is shown that, provided the sound source is well-defined and flow environment is known, conventional infinite duct optimum attenuation rates can be improved. To confirm these results, an experimental program was conducted in a laboratory test facility. The measured data are presented in the form of analytical-experimental correlations. Excellent agreement between theory and experiment verifies and substantiates the analytical prediction techniques. The results indicate that phased liners may be of immediate benefit in the development of improved aircraft exhaust duct noise suppressors