Location of the elevation axis in a large optical telescope

Proposed designs for the next generation of large optical telescopes favor a tripod or quadrupod secondary support, and a primary supported from the back, but it is not yet clear whether the elevation axis should be in front of the primary or behind it. A study is described of the effect of elevation-axis location on key performance parameters (fundamental frequency, blockage, and wind-induced secondary decenter) for a 30-m Cassegrain telescope with a mount configuration that is typical of the new designs. For a fast (e.g., f/1) primary, the best location for the elevation axis is behind the primary. The penalty for moving the elevation axis in front of the primary is roughly a 40% decrease in fundamental frequency and a corresponding reduction in the control bandwidth for pointing and optical alignment

Design Considerations for a Highly Segmented Mirror

Design issues for a 30-m highly segmented mirror are explored, with emphasis on parametric models of simple, inexpensive segments. A mirror with many small segments offers cost savings through quantity production and permits high-order active and adaptive wave-front corrections. For a 30-m f/1.5 paraboloidal mirror made of spherical, hexagonal glass segments, with simple warping harnesses and three-point supports, the maximum segment diameter is ~100 mm, and the minimum segment thickness is ~5 mm. Large-amplitude, low-order gravitational deformations in the mirror cell can be compensated if the segments are mounted on a plate floating on astatic supports. Because gravitational deformations in the plate are small, the segment actuators require a stroke of only a few tens of micrometers, and the segment positions can be measured by a wave-front sensor

Spatial Spectrum Analysis of Wave-Front Correction with a Segmented Mirror

An expression is derived for the spatial power spectrum of wave-front errors after correction with a segmented mirror. This includes estimates of the spectral contributions of segment piston and tilt corrections and spatial aliasing by a regular array of segments. The approach allows rapid computation of wave-front error spectra in systems with highly segmented mirrors

Mirrors with Regular Hexagonal Segments

The point-spread function and emissivity are calculated for a mirror made from regular hexagonal segments of just a few different sizes. A mirror of this type has many similar segments, which is an advantage for manufacturing, and for an ~f/1 mirror with ≥1000 segments and ≥4 sizes of regular hexagons the increase in intersegment gap area is negligible. This result raises the possibility of making a mirror from very large numbers of identical small segments that are warped to the required figure

Millimeter-wave center of curvature test for a fast paraboloid

We describe a technique for measuring the surface profile of a radio telescope with a fast paraboloidal primary. The technique uses a sensor, at the center of curvature of the primary, consisting of a millimeter-wave source and an array of receivers to measure the field in the caustic. The sensor is mounted on the telescope enclosure and it moves with the telescope, so the measurements can be used for continuous, slow, closed-loop control of the surface. Sensor decenter and despace errors, due to wind buffeting and thermal deformation of the sensor support, do not compromise the surface measurements because they result in profile errors that are mainly translation, which has no effect on astronomical observations, or tilt and defocus, which can be measured using astronomical sources. If the position of the sensor is known to 20 μm rms, the surface can be measured to ∼1  μm rms at λ=3  mm

CFRP truss for the CCAT 25 m diameter submillimeter-wave telescope

CCAT will be a 25 m diameter submillimeter-wave telescope that will operate inside a dome located on Cerro Chajnantor in the Atacama Desert. The telescope must have high aperture efficiency at a wavelength of 350 microns and good performance out to a wavelength of 200 microns. A conceptual design for a carbon fiber reinforced plastic (CFRP) truss and primary reflector support truss has been developed. This design yields a telescope with a net �½ wave front error of <10 microns using a lookup table to adjust the segment actuators to compensate for gravitational deflections. Minor corrections may be required to compensate for the expected 20 C temperature excursions. These can be handled using a coarse lookup table

A Sunyaev-Zel'Dovich-Selected Sample of the Most Massive Galaxy Clusters in the 2500 deg^2 South Pole Telescope Survey

The South Pole Telescope (SPT) is currently surveying 2500 deg^2 of the southern sky to detect massive galaxy clusters out to the epoch of their formation using the Sunyaev-Zel'dovich (SZ) effect. This paper presents a catalog of the 26 most significant SZ cluster detections in the full survey region. The catalog includes 14 clusters which have been previously identified and 12 that are new discoveries. These clusters were identified in fields observed to two differing noise depths: 1500 deg^2 at the final SPT survey depth of 18 μK arcmin at 150 GHz and 1000 deg^2 at a depth of 54 μK arcmin. Clusters were selected on the basis of their SZ signal-to-noise ratio (S/N) in SPT maps, a quantity which has been demonstrated to correlate tightly with cluster mass. The S/N thresholds were chosen to achieve a comparable mass selection across survey fields of both depths. Cluster redshifts were obtained with optical and infrared imaging and spectroscopy from a variety of ground- and space-based facilities. The redshifts range from 0.098 ≤ z ≤ 1.132 with a median of z_(med) = 0.40. The measured SZ S/N and redshifts lead to unbiased mass estimates ranging from 9.8 × 10^(14) M_☉ h^(–1)_(70) ≤ M _(200(ρmean)) ≤ 3.1 × 10^(15) M_☉ h^(–1)_(70). Based on the SZ mass estimates, we find that none of the clusters are individually in significant tension with the ΛCDM cosmological model. We also test for evidence of non-Gaussianity based on the cluster sample and find the data show no preference for non-Gaussian perturbations

A 6-12 GHz Analogue Lag-Correlator for Radio Interferometry

Aims: We describe a 6-12 GHz analogue correlator that has been developed for use in radio interferometers. Methods: We use a lag-correlator technique to synthesis eight complex spectral channels. Two schemes were considered for sampling the cross-correlation function, using either real or complex correlations, and we developed prototypes for both of them. We opted for the ``add and square'' detection scheme using Schottky diodes over the more commonly used active multipliers because the stability of the device is less critical. Results: We encountered an unexpected problem, in that there were errors in the lag spacings of up to ten percent of the unit spacing. To overcome this, we developed a calibration method using astronomical sources which corrects the effects of the non-uniform sampling as well as gain error and dispersion in the correlator.Comment: 14 pages, 21 figures, accepted for publication in A&