Wool-reinforced cement based composites

In this paper, an overview of the latest research activities in the field of cement-based composites incorporating sheep wool reinforcement is presented. First, the characteristics of this type of natural fibre are described. Then, the current use of sheep wool fibres in cement-based composites is discussed. The research problems regarding the properties of cement matrix composites reinforced with sheep wool are divided into four groups: thermal and acoustic properties, mechanical behavior, durability issues, and microstructure aspects. The latter two groups are analysed separately, because both durability and microstructure are of particular importance for future applications of wool reinforcement. Finally, the main directions of future researches are presented

Special issue: Supplementary cementitious materials in concrete, part I

Supplementary Cementitious Materials in Concret

Bio-fibres as a reinforcement of gypsum composites

Three series of tests performed on fibre-reinforced gypsum composites are described herein. Sheep wool fibres and hemp fibres were used as reinforcement. The aim was to evaluate the capability of these biomaterials to enhance the fracture toughness of the gypsum matrix. The mechanical properties were measured by means of flexural tests on small specimens, whereas scanning electron microscopy with energy dispersive spectroscopy and X-ray diffraction were used to ana-lyse the microstructure and composition of the fibres and of the gypsum composites. As a result, wool fibres were shown to improve the mechanical performance of the gypsum matrix, better than hemp fibres. This is due to the high adhesion at the interface of the fibre and gypsum matrix, because the latter tends to roughen the surface of the wool and, consequently to increase the bond strength. This preliminary research carried out shows that this type of biofiber—a waste material—can be considered a promising building material in sustainable and environmentally friendly engineering

ASAM : Automatic Architecture Synthesis and Application Mapping; dl. 2.2: Report on initial version of the hierarchical application model

No abstract

Instability of two dimensional graphene: Breaking sp2 bonds with soft X-rays

We study the stability of various kinds of graphene samples under soft X-ray irradiation. Our results show that in single layer exfoliated graphene (a closer analogue to two dimensional material), the in-plane carbon-carbon bonds are unstable under X-ray irradiation, resulting in nanocrystalline structures. As the interaction along the third dimension increases by increasing the number of graphene layers or through the interaction with the substrate (epitaxial graphene), the effect of X-ray irradiation decreases and eventually becomes negligible for graphite and epitaxial graphene. Our results demonstrate the importance of the interaction along the third dimension in stabilizing the long range in-plane carbon-carbon bonding, and suggest the possibility of using X-ray to pattern graphene nanostructures in exfoliated graphene.Comment: 4 pages, 3 figures, Phys. Rev. B rapid communication, in pres

Tracking Cooper Pairs in a Cuprate Superconductor by Ultrafast Angle-Resolved Photoemission

In high-temperature superconductivity, the process that leads to the formation of Cooper pairs, the fundamental charge carriers in any superconductor, remains mysterious. We use a femtosecond laser pump pulse to perturb superconducting Bi2Sr2CaCu2O8+{\delta}, and study subsequent dynamics using time- and angle-resolved photoemission and infrared reflectivity probes. Gap and quasiparticle population dynamics reveal marked dependencies on both excitation density and crystal momentum. Close to the d-wave nodes, the superconducting gap is sensitive to the pump intensity and Cooper pairs recombine slowly. Far from the nodes pumping affects the gap only weakly and recombination processes are faster. These results demonstrate a new window into the dynamical processes that govern quasiparticle recombination and gap formation in cuprates.Comment: 22 pages, 9 figure

Application of the SMALP technology to the isolation of GPCRs from low-yielding cell lines

The ability of styrene–maleic acid (SMAc) co-polymers to spontaneously insert into biological membranes can be exploited to extract G protein-coupled receptors (GPCRs) embedded in styrene–maleic acid lipid particles (SMALPs), preserving the native environment around the protein and thus enhancing the feasibility of functional studies. So far, the SMALP technology has been primarily employed on non-mammalian cells and protocols are not optimized for adherent human cell lines, which cannot be harvested in large amounts. In this work, a fine investigation of key parameters affecting the formation of SMALPs was undertaken with the purpose of maximizing the yield of extraction of a recombinant form of human β2-adrenergic receptor (rhβ2AR) from HEK293T cells. The study highlighted an important influence of ionic strength on the membrane solubilization efficiency and GPCR purification yield of SMAc co-polymers: by lowering the salt concentration of all buffers used in previously published SMALP protocols, the water solubility and extraction efficiency of the selected SMAc co-polymer (commercially supplied as a potassium salt) were enhanced. In-line combination of size-exclusion chromatography (SEC) with immobilized metal affinity chromatography (IMAC) allowed further improvement of the final rhβ2AR yield by reducing the loss of SMALP-embedded GPCRs during the fractionation and purification of SMALPs. The overall findings of this study show that the available SMALP protocols can be significantly optimized in several aspects in order to increase the efficiency of GPCR solubilization and isolation from low-yielding expression systems