Computer modeling of multiple-channel input signals and intermodulation losses caused by nonlinear traveling wave tube amplifiers

The multiple channel input signal to a soft limiter amplifier as a traveling wave tube is represented as a finite, linear sum of Gaussian functions in the frequency domain. Linear regression is used to fit the channel shapes to a least squares residual error. Distortions in output signal, namely intermodulation products, are produced by the nonlinear gain characteristic of the amplifier and constitute the principal noise analyzed in this study. The signal to noise ratios are calculated for various input powers from saturation to 10 dB below saturation for two specific distributions of channels. A criterion for the truncation of the series expansion of the nonlinear transfer characteristic is given. It is found that he signal to noise ratios are very sensitive to the coefficients used in this expansion. Improper or incorrect truncation of the series leads to ambiguous results in the signal to noise ratios

Design of high-perveance confined-flow guns for periodic-permanent-magnet-focused tubes

An approach to the design of high perveance, low compression guns is described in which confinement is used to stabilize the beam for subsequent periodic-permanent-magnet focusing. The computed results for two cases are presented. A magnetic boundary value problem was solved for the scalar potential from which the axial magnetic field was computed. A solution was found by iterating between Poisson's equation and the electron trajectory calculations. Magnetic field values were varied in magnitude until a laminar beam with minimum scalloping was produced

Refocusing properties of periodic magnetic fields

The use of depressed collectors for the efficient collection of spent beams from linear-beam microwave tubes depends on a refocusing procedure in which the space charge forces and transverse velocity components are reduced. The refocusing properties are evaluated of permanent magnet configurations whose axial fields are approximated by constant plateaus or linearly varying fields. The results provide design criteria and show that the refocusing properties can be determined from the plateau fields alone

Evaluation of magnetic refocusing in linear-beam microwave tubes

Magnetic field configurations in which the axial component of the field decays linearly to a constant plateau field are evaluated for use in refocusing the output beam of linear beam microwave tubes. The slope of the decay and the value of the plateau field are parameters in this study. A uniform beam with a space charge force only in the radial direction is assumed, and the electron trajectories are computed for various classes. For a given magnetic configuration (slope and plateau value) the plateau length is calculated for a specified class and the rms deviation of the output angles for all classes is computed at the end of this plateau length. A minimum condition for a refocused beam is defined to be one in which the rms value of the output angles is less than the rms input. Many of the configurations satisfied this criteria and successfully reduced the rms value by half

TWT design requirements for 30/20 GHz digital communications' satellite

The rapid growth of communication traffic (voice, data, and video) requires the development of additional frequency bands before the 1990's. The frequencies currently in use for satellite communications at 6/4 GHz are crowded and demands for 14/12 GHz systems are increasing. Projections are that these bands will be filled to capacity by the late 1980's. The next higher frequency band allocated for satellite communications is at 30/20 GHz. For interrelated reasons of efficiency, power level, and system reliability criteria, a candidate for the downlink amplifier in a 30/20 GHz communications' satellite is a dual mode traveling wave tube (TWT) equipped with a highly efficient depressed collector. A summary is given of the analyses which determine the TWT design requirements. The overall efficiency of such a tube is then inferred from a parametric study and from experimental data on multistaged depressed collectors. The expected TWT efficiency at 4 dB below output saturation is 24 percent in the high mode and 22 percent in the low mode

Analytical prediction with multidimensional computer programs and experimental verification of the performance, at a variety of operating conditions, of two traveling wave tubes with depressed collectors

Experimental and analytical results are compared for two high performance, octave bandwidth TWT's that use depressed collectors (MDC's) to improve the efficiency. The computations were carried out with advanced, multidimensional computer programs that are described here in detail. These programs model the electron beam as a series of either disks or rings of charge and follow their multidimensional trajectories from the RF input of the ideal TWT, through the slow wave structure, through the magnetic refocusing system, to their points of impact in the depressed collector. Traveling wave tube performance, collector efficiency, and collector current distribution were computed and the results compared with measurements for a number of TWT-MDC systems. Power conservation and correct accounting of TWT and collector losses were observed. For the TWT's operating at saturation, very good agreement was obtained between the computed and measured collector efficiencies. For a TWT operating 3 and 6 dB below saturation, excellent agreement between computed and measured collector efficiencies was obtained in some cases but only fair agreement in others. However, deviations can largely be explained by small differences in the computed and actual spent beam energy distributions. The analytical tools used here appear to be sufficiently refined to design efficient collectors for this class of TWT. However, for maximum efficiency, some experimental optimization (e.g., collector voltages and aperture sizes) will most likely be required

Molecular Composition of the Louse Sheath

Flash pyrolysis-gas chromatography/mass spectrometry was used to assess the chemical composition of the head louse\u27s nit sheath. The pyrolyzate of the female insect\u27s secretions, which form a cement-like cylinder holding the egg onto the hair, is dominated by amino acid derivatives and fatty acids. No chitin-specific compounds were detected in the sheath. These results, contrary to previous reports, show that the polymeric complex of the sheath is composed of proteinaceous moieties, possibly cross-linked to aliphatic components. This study constitutes the first chemical characterization of the pyrolysis products of insect (louse) glue and unequivocally confirms that louse sheaths are not chitinous, as suggested by earlier histochemical studies. Development of agents that might loosen nits from the hair shaft is dependent on research that addresses the chemical composition of the nit sheath

Visualization of Exact Invariant Solutions Associated with Atmospheric Waves in a Thin Circular Layer

The purpose of the research was to investigate the exact solutions of nonlinear shallow water equations associated with planetary equatorial waves corresponding to the Cauchy-Poisson free boundary problem describing the nonstationary motion of an incompressible perfect fluid propagating around a solid circle. We consider water waves for which the ratio of the depth of fluid above the circular bottom to the radius of the circle is small (shallow water)

CAV3 mutation in a patient with transient hyperCKemia and myalgia

Mutations in caveolin-3 (CAV3) can lead to different clinical phenotypes affecting skeletal or cardiac muscles. Here, we describe a patient with Klinefelter syndrome, ulcerative colitis and Sjögren syndrome, who developed transient hyperCKemia, myalgia and mild muscular weakness. Using whole exome sequencing (WES), a missense mutation G169A was found in the CAV3 gene. In addition, we identified a homozygous frameshift deletion in MS4A12 that may contribute to inflammatory bowel disease, further demonstrating usefulness of WES in dual molecular diagnoses

Electronic structure of the (111) and (-1-1-1) surfaces of cubic BN: A local-density-functional ab initio study

We present ab initio local-density-functional electronic structure calculations for the (111) and (-1-1-1) surfaces of cubic BN. The energetically stable reconstructions, namely the N adatom, N3 triangle models on the (111), the (2x1), boron and nitrogen triangle patterns on the (-1-1-1) surface are investigated. Band structure and properties of the surface states are discussed in detail.Comment: 8 pages, 12 figure