78,705 research outputs found
Effect of geometry and operating conditions on spur gear system power loss
The results of an analysis of the effects of spur gear size, pitch, width, and ratio on total mesh power loss for a wide range of speeds, torques, and oil viscosities are presented. The analysis uses simple algebraic expressions to determine gear sliding, rolling, and windage losses and also incorporates an approximate ball bearing power loss expression. The analysis shows good agreement with published data. Large diameter and fine pitched gears had higher peak efficiencies but low part load efficiency. Gear efficiencies were generally greater than 98 percent except at very low torque levels. Tare (no-load) losses are generally a significant percentage of the full load loss except at low speeds
Spur-Gear-System Efficiency at Part and Full Load
A simple method for predicting the part- and full-load power loss of a steel spur gearset of arbitrary geometry supported by ball bearings is described. The analysis algebraically accounts for losses due to gear sliding, rolling traction, and windage in addition to support-ball-bearing losses. The analysis compares favorably with test data. A theoretical comparison of the component losses indicates that losses due to gear rolling traction, windage, and support bearings are significant and should be included along with gear sliding loss in a calculation of gear-system power loss
Comparison of spur gear efficiency prediction methods
The predictions of five spur-gear efficiency calculation methods were compared with three sets of test data using different gear geometries. The data and the analysis methods were limited to jet lubricated, ground, spur gears. The data covered a range in pitch line velocity to 1 to 20 m/sec (200 to 4000 ft/min) and K-load factor range of 17 to 1600
Efficiency of nonstandard and high contact ratio involute spur gears
A power loss prediction was extended to include involute spur gears of nonstandard proportions. The method is used to analyze the effects of modified addendum, tooth thickness, and gear center distance in addition to the parameters previously considered which included gear diameter, pitch, pressure angle, face width, oil viscosity, speed, and torque. Particular emphasis was placed on high contact ratio gearing (contact ratios greater than two). Despite their higher sliding velocities, high contact ratio gears are designed to levels of efficiency comparable to those of conventional gears while retaining their advantages through proper selection of gear geometry
Design of Spur Gears for Improved Efficiency
A method to calculate spur gear system loss for a wide range of gear geometries and operating conditions was used to determine design requirements for an efficient gearset. The effects of spur gear size, pitch, ratio, pitch line velocity and load on efficiency were determined. Peak efficiencies were found to be greater for large diameter and fine pitched gears and tare (no-load) losses were found to be significant
Evaluation of a high performance, fixed-ratio, traction drive
A test program was initiated to evaluate the key operational and performance factors associated with the Nasvytis multiroller concept. Two sets of Nasvytis drives, each of slightly geometry, were parametrically tested on a back to back test stand. Initial results from these tests are reported. One of these units was later retrofitted to the power turbine of an automotive gas turbine engine and dynamometer tested
Rim inertial measuring system
The invention includes an angular momentum control device (AMCD) having a rim and several magnetic bearing stations. The AMCD is in a strapped down position on a spacecraft. Each magnetic bearing station comprises means, including an axial position sensor, for controlling the position of the rim in the axial direction; and means, including a radial position sensor, for controlling the position of the rim in the radial direction. A first computer receives the signals from all the axial position sensors and computes the angular rates about first and second mutually perpendicular axes in the plane of the rim and computes the linear acceleration along a third axis perpendicular to the first and second axes. A second computer receives the signals from all the radial position sensors and computes the linear accelerations along the first and second axes
Interference between a large number of independent Bose-Einstein condensates
We study theoretically the interference patterns produced by the overlap of
an array of Bose-Einstein condensates that have no phase coherence among them.
We show that density-density correlations at different quasimomenta, which play
an important role in two-condensate interference, become negligible for large
, where is the number of overlapping condensates. In order to understand
the physics of this phenomenon, it is sufficient to consider the periodicity of
the lattice and the statistical probability distribution of a random-walk
problem. The average visibility of such interference patterns decreases as
for large .Comment: 9 pages, 2 figure
Aspect ratio analysis for ground states of bosons in anisotropic traps
Characteristics of the initial condensate in the recent experiment on
Bose-Einstein condensation (BEC) of Rb atoms in an anisotropic
magnetic trap is discussed. Given the aspect ratio , the quality of BEC is
estimated. A simple analytical Ansatz for the initial condensate wave function
is proposed as a function of the aspect ratio which, in contrast to the
Baym-Pethick trial wave function, reproduces both the weak and the strong
intaraction limits and which is in better agreement with numerical results than
the latter.Comment: 12 pages, latex, 3 figures added, minor corrections; to appear in J.
Res. Nat. Inst. of Standards and Technolog
Mobile radio alternative systems study, executive summary
Present day mobile communication technologies, systems and equipment are described from background in evaluating the concepts generated in the study. Average propagation ranges are calculated for terrestrial installations in each of seven physiographic areas of the contiguous states to determine the number of installations that would be required for nationwide coverage. Four system concepts are defined and analyzed to determine how well terrestrial systems can fulfill the requirements at acceptable costs
- …