Computational simulation of matrix micro-slip bands in SiC/Ti-15 composite

Computational simulation procedures are used to identify the key deformation mechanisms for (0)(sub 8) and (90)(sub 8) SiC/Ti-15 metal matrix composites. The computational simulation procedures employed consist of a three-dimensional finite-element analysis and a micromechanics based computer code METCAN. The interphase properties used in the analysis have been calibrated using the METCAN computer code with the (90)(sub 8) experimental stress-strain curve. Results of simulation show that although shear stresses are sufficiently high to cause the formation of some slip bands in the matrix concentrated mostly near the fibers, the nonlinearity in the composite stress-strain curve in the case of (90)(sub 8) composite is dominated by interfacial damage, such as microcracks and debonding rather than microplasticity. The stress-strain curve for (0)(sub 8) composite is largely controlled by the fibers and shows only slight nonlinearity at higher strain levels that could be the result of matrix microplasticity

Dynamic analysis of a pre-and-post ice impacted blade

The dynamic characteristics of an engine blade are evaluated under pre-and-post ice impact conditions using the NASA in-house computer code BLASIM. The ice impacts the leading edge of the blade causing severe local damage. The local structural response of the blade due to the ice impact is predicted via a transient response analysis by modeling only a local patch around the impact region. After ice impact, the global geometry of the blade is updated using deformations of the local patch and a free vibration analysis is performed. The effects of ice impact location, size and ice velocity on the blade mode shapes and natural frequencies are investigated. The results indicate that basic nature of the mode shapes remains unchanged after impact and that the maximum variation in natural frequencies occurs for the twisting mode of the blade

Structural tailoring of aircraft engine blade subject to ice impact constraints

Results are presented for the minimum weight design of SR2 unswept blade made of (titanium/graphite-epoxy/titanium) sub s fiber composite. The blade which is rotating at high RPM is subject to ice impact. The root chord length, blade thicknesses at five stations, and graphite-epoxy ply orientation are chosen as design variables. Design constraints are placed on the behavior variables: local leading edge strain and root damage parameter (combined stress failure criteria) as a function due to ice impact, maximum spanwise centrifugal stress at the root of the deformed blade due to local damage, first three natural frequencies, and resonance margin after impact. The method of feasible directions is employed to solve the inequality constrained minimization problem. The effect of ice speed and the ice impact location on the final design are discussed

Root damage analysis of aircraft engine blade subject to ice impact

The blade root response due to ice impact on an engine blade is simulated using the NASA in-house code BLASIM. The ice piece is modeled as an equivalent spherical object impacting on the leading edge of the blade and has the velocity opposite to that of the aircraft with direction parallel to the engine axis. The effect of ice impact is considered to be an impulse load on the blade with its amplitude computed based on the momentum transfer principle. The blade response due to the impact is carried out by modal superposition using the first three modes. The maximum dynamic stresses at the blade root are computed at the quarter cycle of the first natural frequency. A combined stress failure function based on modified distortion energy is used to study the spanwise bending damage response at the blade root. That damage function reaches maximum value for very low ice speeds and increases steeply with increases in engine speed

Aerothermal modeling program. Phase 2, element B: Flow interaction experiment

NASA has instituted an extensive effort to improve the design process and data base for the hot section components of gas turbine engines. The purpose of element B is to establish a benchmark quality data set that consists of measurements of the interaction of circular jets with swirling flow. Such flows are typical of those that occur in the primary zone of modern annular combustion liners. Extensive computations of the swirling flows are to be compared with the measurements for the purpose of assessing the accuracy of current physical models used to predict such flows

Aerothermal modeling program, phase 2

The main objectives of the Aerothermal Modeling Program, Phase 2 are: to develop an improved numerical scheme for incorporation in a 3-D combustor flow model; to conduct a benchmark quality experiment to study the interaction of a primary jet with a confined swirling crossflow and to assess current and advanced turbulence and scalar transport models; and to conduct experimental evaluation of the air swirler interaction with fuel injectors, assessments of current two-phase models, and verification the improved spray evaporation/dispersion models

Hierarchical nonlinear behavior of hot composite structures

Hierarchical computational procedures are described to simulate the multiple scale thermal/mechanical behavior of high temperature metal matrix composites (HT-MMC) in the following three broad areas: (1) behavior of HT-MMC's from micromechanics to laminate via METCAN (Metal Matrix Composite Analyzer), (2) tailoring of HT-MMC behavior for optimum specific performance via MMLT (Metal Matrix Laminate Tailoring), and (3) HT-MMC structural response for hot structural components via HITCAN (High Temperature Composite Analyzer). Representative results from each area are presented to illustrate the effectiveness of computational simulation procedures and accompanying computer codes. The sample case results show that METCAN can be used to simulate material behavior such as the entire creep span; MMLT can be used to concurrently tailor the fabrication process and the interphase layer for optimum performance such as minimum residual stresses; and HITCAN can be used to predict the structural behavior such as the deformed shape due to component fabrication. These codes constitute virtual portable desk-top test laboratories for characterizing HT-MMC laminates, tailoring the fabrication process, and qualifying structural components made from them

Hierarchical Simulation of Hot Composite Structures

Computational procedures are described to simulate the thermal and mechanical behavior of high temperature metal matrix composites (HT-MMC) in the following three broad areas: (1) Behavior of HT-MMC's from micromechanics to laminate via Metal Matrix Composite Analyzer (METCAN), (2) tailoring of HT-MMC behavior for optimum specific performance via Metal Matrix Laminate Tailoring (MMLT), and (3) HT-MMC structural response for hot structural components via High Temperature Composite Analyzer (HITCAN). Representative results from each area are presented to illustrate the effectiveness of computational simulation procedures. The sample case results show that METCAN can be used to simulate material behavior such as strength, stress-strain response, and cyclic life in HTMMC's; MMLT can be used to tailor the fabrication process for optimum performance such as that for in-service load carrying capacity of HT-MMC's; and HITCAN can be used to evaluate static fracture and fatigue life of hot pressurized metal matrix composite rings

Exclusion statistics: A resolution of the problem of negative weights

We give a formulation of the single particle occupation probabilities for a system of identical particles obeying fractional exclusion statistics of Haldane. We first derive a set of constraints using an exactly solvable model which describes an ideal exclusion statistics system and deduce the general counting rules for occupancy of states obeyed by these particles. We show that the problem of negative probabilities may be avoided with these new counting rules.Comment: REVTEX 3.0, 14 page

Ignition Delay Studies on Hypergolic Fuel Grains

The ignition delays of several solid hypergolic fuel compositions, casted using various polymeric binders, or as melts, have been determined with fuming nitric acid as oxidizer. The ignition delays of various hypergolic fuel compositions increase drasticaliy on casting with binders like. carboxyl or hydroxyl termninated polybutadiene. Fuel grains cast using some newly syhthesised epoxy  resins with other ingrcdients, such as curing agent, magnesium powder and fuel, have short ignition delays of the order of 200 ms, and also good mechanical strength. Increasing the amount of binder in the composition retards the hypergolicity of the rain. Similar studies have been made on melt-cast systems using low melting hypergolic fuels for casting fuel powders. The ignition delays of the melt-cast grains, are longer than those determined taking the composition in the powder form. The effect of highly hypergolic additives, and metal powders, on the ignition delay of the cast compositions has been determined. Grains having good mechanical strength and short ignition delays have been obtained by optimising the fuel grain composition