The 3D-Printed Non-Radiating Edge Gap-Coupled Curved Patch Antenna

The use of parasitic resonant patches is a widespread technique to improve the bandwidth of microstrip patch antennas. Exploiting the free form-factor allowed by 3D-printing manufacturing technology, we present here a novel curved patch antenna layout, based on the non-radiating edge gap-coupled patch configuration. The proposed antenna is composed of a central curved patch, fed by a coaxial probe, and two gap-coupled parasitic side curved patches. This solution features a percentage impedance bandwidth of 16.3% using symmetrical parasitic side patches and 31.5% using asymmetrical side patches. A significant improvement of the bandwidth in comparison with both the standard non-radiating edge gap-coupled microstrip antenna (6.1% bandwidth) and the standard curved patch antenna (9% bandwidth) is achieved. Design and optimization of the proposed configuration are performed using the commercial software CST Studio Suite at the center frequency of 2.45 GHz. Prototypes of the symmetrical curved non-radiating edge gap-coupled patch antenna have been manufactured for the experimental verification, using a curved 3D-printed polylactic acid (PLA) substrate, fabricated with the commercial 3D printer PRUSA MK3S + and a 50 μ m -thick adhesive aluminum tape for the metallization. Measured results show a very good agreement with simulations

A Novel Design for Dual-Band Wearable Textile Eighth-Mode SIW Antennas

A novel wearable textile dual-band antenna configuration based on a substrate integrated waveguide (SIW) cavity is presented. The miniaturization of the antenna is achieved by exploiting the magnetic field symmetry of a square SIW cavity, reducing its size to 1/8 of the full square cavity with an eighth-mode SIW configuration. This solution is applied to the design of a wearable dual-band antenna for Long Range (LoRa) applications. The antenna operating frequency covers both the UHF LoRa bands, the European (863-870 MHz) and the North American (902-928 MHz). The proposed design provides a low-cost and compact antenna, which is easy to fabricate and ensures a very good isolation and robustness with respect to the human body proximity. The commercial software CST Studio Suite has been used for the antenna design and simulations. A prototype has been fabricated and the measured results are in good agreement with numerical simulations

Generation of two genomic-integration-free DMD iPSC lines with mutations affecting all dystrophin isoforms and potentially amenable to exon-skipping

Duchenne muscular dystrophy (DMD) is the most common paediatric muscular dystrophy and is caused by mutations in the DYSTROPHIN gene. We generated two induced pluripotent stem cell (iPSC) lines from DMD patients with nonsense mutations in exons 68 (UCLi011-A) or 70 (UCLi012-A) by transfecting reprogramming mRNAs. Both mutations affect expression of all dystrophin isoforms. iPSCs expressed pluripotency-associated markers, differentiated into cells of the three germ layers in vitro and had normal karyotypes. The selected mutations are potentially amenable to read-through therapies, exon-skipping and gene-editing. These new iPSCs are also relevant to study DYSTROPHIN role in tissues other than skeletal muscle

Lessons Learned From Translational Research in Neuromuscular Diseases: Impact on Study Design, Outcome Measures and Managing Expectation

Spinal Muscular Atrophy (SMA) and Duchenne Muscular Dystrophy (DMD), two of the most common, child onset, rare neuromuscular disorders, present a case study for the translation of preclinical research into clinical work. Over the past decade, well-designed clinical trials and innovative methods have led to the approval of several novel therapies for SMA and DMD, with many more in the pipeline. This review discusses several features that must be considered during trial design for neuromuscular diseases, as well as other rare diseases, to maximise the possibility of trial success using historic examples. These features include well-defined inclusion criteria, matching criteria, alternatives to placebo-controlled trials and the selection of trial endpoints. These features will be particularly important in the coming years as the investigation into innovative therapy approaches for neuromuscular diseases continues

A robust wearable textile SIW RFID antenna

A wearable textile Radio Frequency Identification (RFID) tag realized on a substrate integrated waveguide cavity is presented, operating in the European UHF RFID frequency band. The antenna shows a very good isolation with respect to the human body, and a satisfactory robustness to antenna-body distance variations. The resulting tag is very compact, since its size has been reduced by exploiting the symmetry of a SIW cylindrical resonant cavity and obtaining an eighth mode SIW antenna, and can be produced at low-cost through simple manufacturing processes

Crowded space: a review on radar measurements for space debris monitoring and tracking

Space debris monitoring is nowadays a priority for worldwide space agencies, due to the serious threat that these objects present. More and more efforts have been made to extend the network of available radar systems devoted to the control of space. A meticulous review has been done in this paper, in order to find and classify the considerable amounts of data provided by the scientific community that deal with RADAR measurement for the debris monitoring and tracking. The information gathered is organized based on the volume of found data and classified taking into account the geographical location of the facilities

Microwave heating improvement: permittivity characterization of water–ethanol and water–NaCl binary mixtures

Microwave heating offers a lot of advantages compared to conventional heating methods in the chemical reactions field due to its positive effects on reaction time and selectivity. Dielectric properties, and in particular permittivity, of substances and mixtures, are important for the optimization of microwave heating processes; notwithstanding this, specific databases are poor and far from being complete, and in the scientific literature very little data regarding these properties can be found. In this work, impedance measurements were carried out using a specially designed system to get the real and imaginary parts of the dielectric constant. The apparatus was tested in the estimation of permittivity of water–ethanol and water–NaCl mixtures, varying their composition to obtain a wide range of permittivity values. The results were compared to literature data and fitted with available literature models to verify the correspondence between them, finding that permittivity dependence on mixture composition can be effectively described by the models

Electromagnetic characterisation of conductive 3D-Printable filaments for designing fully 3D-Printed antennas

Additive manufacturing (AM) 3D-printing technology is increasingly bringing benefits even in electromagnetics, with interesting prospects of application. Apart from the use of additive manufacturing for realising dielectric components of suitably shaped antennas, the ambitious target is, undoubtedly, the fully 3D realisation of radiofrequency and microwave circuits as well as radiating structures, including, therefore, conductive parts. In this regard, 3D-printable filaments with interesting conductive properties are being produced. However, their rigorous conductivity characterisation is still missing, making it difficult to estimate the real behaviour of the final 3D printed electromagnetic device. To fill this gap, the conductivity of one of the most interesting conductive filaments, named Electrifi, is first experimentally evaluated in a frequency range as large as 0.72-6 GHz, accounting also for its roughness. Then it has been validated by designing, realising, and testing three fully 3D-printed antennas. Specifically, two bow-tie antennas, operating at 2.8 and 4 GHz, respectively, and an ultrawideband antenna, borrowed from the existing literature, operating between 1 and 7 GHz. The good agreement between simulated and measured results demonstrates the reliability of the performed electrical conductivity characterisation, even in the design of efficient radiating structures entirely realised with thermoplastic materials with copper nanoparticle additives

A Curved Microstrip Patch Antenna Designed From Transparent Conductive Films

Transparent microstrip patch antennas suffer from low radiation efficiency and gain when manufactured using transparent conductive films (TCFs), mainly at low frequency (starting from the microwave S band). To address this problem, we propose a curved microstrip patch antenna designed using transparent materials. This new configuration has proven to be a simple and effective solution to improve the radiation efficiency and gain of TCF printed antennas. In fact, when typical values of the TCF surface resistance are considered (between 2 and 10 Ω/sq), the new antenna features a radiation efficiency of up to 72.3% and a realized gain of up to 5.3 dBi at 2.15 GHz, with a significant improvement in comparison with the flat transparent microstrip antenna (up to 17.7% radiation efficiency, and 0.5 dBi realized gain). Good transparency and lightweight is ensured by the deposition of the TCF on a polyethylene terephthalate film, which lies, in turn, on a 3D-printed curved polyethylene terephthalate glycol supporting frame. Simulations using Ansys HFSS are presented to demonstrate the potential of the proposed configuration. Then, a prototype of the transparent curved patch antenna is fabricated and measured to assess the simulated results

Evaluating the Effectiveness of Planar and Waveguide 3D-Printed Antennas Manufactured Using Dielectric and Conductive Filaments

3D printing is a technology suitable for creating electronics and electromagnetic devices. However, the manufacturing of both dielectric and conductive parts in the same process still remain a challenging task. This study explores the combination of 3D printing with traditional manufacturing techniques for antenna design and fabrication, giving the designer the advantage of using the additive manufacturing technology only to implement the most critical parts of a certain structure, ensuring a satisfying electromagnetic performance, but limiting the production cost and complexity. In the former part of the study, the focus is on three proximity-coupled patch antennas. It demonstrates how hybrid devices made of metal, dielectric, and 3D-printed (using Fused Filament Fabrication) conductive polymers can be successfully simulated and created for different operating frequency bands. In the latter part, the study compares three prototypes of a 5G-NR, high gain, and wideband waveguide antenna: respectively a fully 3D printed one made of electrifi (which is the most conductive commercial 3D-printable filament), an all-metal one, and a hybrid (3D-printed electrifi & metal) one. The results show a 15% reduction in efficiency when using the all-Electrifi configuration compared to all-metal one, and a 4-5% reduction when using the hybrid version