Investigation of Kevlar fabric based materials for use with inflatable structures

Design, manufacture and testing of laminated and coated composite materials incorporating a structural matrix of Kevlar are reported in detail. The practicality of using Kevlar in aerostat materials is demonstrated and data are provided on practical weaves, lamination and coating particulars, rigidity, strength, weight, elastic coefficients, abrasion resistance, crease effects, peel strength, blocking tendencies, helium permeability, and fabrication techniques. Properties of the Kevlar based materials are compared with conventional, Dacron reinforced counterparts. A comprehensive test and qualification program is discussed and quantitative biaxial tensile and shear test data are provided. The investigation shows that single ply laminates of Kevlar and plastic films offer significant strength to weight improvements, are less permeable than two ply coated materials, but have a lower flex life

An atlas of 1975 GEOS-3 radar altimeter data for hurricane/tropical disturbance studies, volume 1

Geographic locations of 1975 hurricanes and other tropical disturbances were correlated with the closest approaching orbits of the GEOS-3 satellite and its radar altimeter. The disturbance locations and altimeter data were gathered for a seven-month period beginning with GEOS-3 launch in mid-April 1975. Areas of coverage were the Atlantic Ocean, the Carribean, the Gulf of Mexico, the west coast of the continental United States, and the central and western Pacific Ocean. Volume 1 contains disturbance coverage data for the Atlantic Ocean, Gulf of Mexico, and Eastern Pacific Ocean. Central and Western Pacific coverage is documented in Volume II

Investigation of Kevlar fabric-based materials for use with inflatable structures

Design, manufacture and testing of laminated and coated composite materials incorporating a structural matrix of Kevlar are reported. The practicality of using Kevlar in aerostat materials is demonstrated, and data are provided on practical weaves, lamination and coating particulars, rigidity, strength, weight, elastic coefficients, abrasion resistance, crease effects, peel strength, blocking tendencies, helium permeability, and fabrication techniques. Properties of the Kevlar-based materials are compared with conventional Dacron-reinforced counterparts. A comprehensive test and qualification program is discussed, and considerable quantitative biaxial tensile and shear test data are provided

First Experiences Integrating PC Distributed I/O Into Argonne's ATLAS Control System

First Experiences Integrating PC Distributed I/O Into Argonne's ATLAS Control System The roots of ATLAS (Argonne Tandem-Linac Accelerator System) date back to the early 1960s. Located at the Argonne National Laboratory, the accelerator has been designated a National User Facility, which focuses primarily on heavy-ion nuclear physics. Like the accelerator it services, the control system has been in a constant state of evolution. The present real-time portion of the control system is based on the commercial product Vsystem [1]. While Vsystem has always been capable of distributed I/O processing, the latest offering of this product provides for the use of relatively inexpensive PC hardware and software. This paper reviews the status of the ATLAS control system, and describes first experiences with PC distributed I/O.Comment: ICALEPCS 2001 Conference, PSN WEAP027, 3 pages, 1 figur

An atlas of 1975 GEOS-3 radar altimeter data for hurricane/tropical disturbance studies, volume 2

For abstract, see N77-24726

Advanced ceramic coating development for industrial/utility gas turbine applications

The effects of ceramic coatings on the lifetimes of metal turbine components and on the performance of a utility turbine, as well as of the turbine operational cycle on the ceramic coatings were determined. When operating the turbine under conditions of constant cooling flow, the first row blades run 55K cooler, and as a result, have 10 times the creep rupture life, 10 times the low cycle fatigue life and twice the corrosion life with only slight decreases in both specific power and efficiency. When operating the turbine at constant metal temperature and reduced cooling flow, both specific power and efficiency increases, with no change in component lifetime. The most severe thermal transient of the turbine causes the coating bond stresses to approach 60% of the bond strengths. Ceramic coating failures was studied. Analytic models based on fracture mechanics theories, combined with measured properties quantitatively assessed both single and multiple thermal cycle failures which allowed the prediction of coating lifetime. Qualitative models for corrosion failures are also presented

Ablation debris control by means of closed thick film filtered water immersion

The performance of laser ablation generated debris control by means of open immersion techniques have been shown to be limited by flow surface ripple effects on the beam and the action of ablation plume pressure loss by splashing of the immersion fluid. To eradicate these issues a closed technique has been developed which ensured a controlled geometry for both the optical interfaces of the flowing liquid film. This had the action of preventing splashing, ensuring repeatable machining conditions and allowed for control of liquid flow velocity. To investigate the performance benefits of this closed immersion technique bisphenol A polycarbonate samples have been machined using filtered water at a number of flow velocities. The results demonstrate the efficacy of the closed immersion technique: a 93% decrease in debris is produced when machining under closed filtered water immersion; the average debris particle size becomes larger, with an equal proportion of small and medium sized debris being produced when laser machining under closed flowing filtered water immersion; large debris is shown to be displaced further by a given flow velocity than smaller debris, showing that the action of flow turbulence in the duct has more impact on smaller debris. Low flow velocities were found to be less effective at controlling the positional trend of deposition of laser ablation generated debris than high flow velocities; but, use of excessive flow velocities resulted in turbulence motivated deposition. This work is of interest to the laser micromachining community and may aide in the manufacture of 2.5D laser etched patterns covering large area wafers and could be applied to a range of wavelengths and laser types

Knowledge of and Attitudes toward Behavioral Health Services among Older Youth in the Foster Care System

This study examined knowledge of and attitudes toward services among 268 17-year olds with psychiatric diagnoses preparing to exit foster care. A structured interview assessed knowledge of services with vignette scenarios and attitudes with a standardized scale. Descriptive statistics described the extent of knowledge and attitudes among this population and regression analyses examined predictors of these dimensions of literacy. Most youth suggested a help source, but responses often lacked specificity. Gender and depression were the strongest predictors of knowledge and attitudes, respectively. Knowing which aspects of literacy are low, and for whom, can inform education efforts to improve access to care in adulthood

Preliminary Solar Sail Design and Fabrication Assessment: Spinning Sail Blade, Square Sail Sheet

Blade design aspects most affecting producibility and means of measurement and control of length, scallop, fullness and straightness requirements and tolerances were extensively considered. Alternate designs of the panel seams and edge reinforcing members are believed to offer advantages of seam integrity, producibility, reliability, cost and weight. Approaches to and requirements for highly specialized metalizing methods, processes and equipment were studied and identified. Alternate methods of sail blade fabrication and related special machinery, tooling, fixtures and trade offs were examined. A preferred and recommended approach is also described. Quality control plans, inspection procedures, flow charts and special test equipment associated with the preferred manufacturing method were analyzed and are discussed