2,002 research outputs found
Investigation of Kevlar fabric based materials for use with inflatable structures
Design, manufacture and testing of laminated and coated composite materials incorporating a structural matrix of Kevlar are reported in detail. The practicality of using Kevlar in aerostat materials is demonstrated and data are provided on practical weaves, lamination and coating particulars, rigidity, strength, weight, elastic coefficients, abrasion resistance, crease effects, peel strength, blocking tendencies, helium permeability, and fabrication techniques. Properties of the Kevlar based materials are compared with conventional, Dacron reinforced counterparts. A comprehensive test and qualification program is discussed and quantitative biaxial tensile and shear test data are provided. The investigation shows that single ply laminates of Kevlar and plastic films offer significant strength to weight improvements, are less permeable than two ply coated materials, but have a lower flex life
The effect of configuration on strength, durability, and handle of Kevlar fabric-based materials
Five Kevlar based laminates and three Kevlar based coated materials were designed, hand made, and tested against comparative conventional Dacron based materials for strength, peel, tear, puncture, creases, and handle. Emphasis was placed on evaluating geometric orientation of constituents, use of elastomeric film in place of high modulus films, and the use of flying thread loom bias reinforcement of Kevlar yarns. Whereas, the performance of the Kevlar laminates was severely degraded by crease effects, significant gains in overall performance factors were shown for the coated Kevlar materials
Investigation of Kevlar fabric-based materials for use with inflatable structures
Design, manufacture and testing of laminated and coated composite materials incorporating a structural matrix of Kevlar are reported. The practicality of using Kevlar in aerostat materials is demonstrated, and data are provided on practical weaves, lamination and coating particulars, rigidity, strength, weight, elastic coefficients, abrasion resistance, crease effects, peel strength, blocking tendencies, helium permeability, and fabrication techniques. Properties of the Kevlar-based materials are compared with conventional Dacron-reinforced counterparts. A comprehensive test and qualification program is discussed, and considerable quantitative biaxial tensile and shear test data are provided
An atlas of 1975 GEOS-3 radar altimeter data for hurricane/tropical disturbance studies, volume 1
Geographic locations of 1975 hurricanes and other tropical disturbances were correlated with the closest approaching orbits of the GEOS-3 satellite and its radar altimeter. The disturbance locations and altimeter data were gathered for a seven-month period beginning with GEOS-3 launch in mid-April 1975. Areas of coverage were the Atlantic Ocean, the Carribean, the Gulf of Mexico, the west coast of the continental United States, and the central and western Pacific Ocean. Volume 1 contains disturbance coverage data for the Atlantic Ocean, Gulf of Mexico, and Eastern Pacific Ocean. Central and Western Pacific coverage is documented in Volume II
Powder metallurgy bearings for advanced rocket engines
Traditional ingot metallurgy was pushed to the limit for many demanding applications including antifriction bearings. New systems require corrosion resistance, better fatigue resistance, and higher toughness. With conventional processing, increasing the alloying level to achieve corrosion resistance results in a decrease in other properties such as toughness. Advanced powder metallurgy affords a viable solution to this problem. During powder manufacture, the individual particle solidifies very rapidly; as a consequence, the primary carbides are very small and uniformly distributed. When properly consolidated, this uniform structure is preserved while generating a fully dense product. Element tests including rolling contact fatigue, hot hardness, wear, fracture toughness, and corrosion resistance are underway on eleven candidate P/M bearing alloys and results are compared with those for wrought 440C steel, the current SSME bearing material. Several materials which offer the promise of a significant improvement in performance were identified
A New Low Reynolds Number Facility for Active Flow Control Applications
Recent interest in gaining understanding of the dynamics and behavior of the leading-edge vortex structure observed in biological flight systems has prompted the construction of a new low Reynolds number facility. This facility, a recirculating oil tunnel, gives several distinct advantages over similar facilities, utilizing water or air as the working fluid, for this kind of study. Additionally, as understanding is gained, active flow control strategies leading to the stabilization of the leading-edge vortex structure will be investigated, and this facility is specially equipped to enable this study. The tunnel has been designed and installed at the California Institute of Technology Graduate Aeronautical Laboratories. Design features of the facility will be discussed, along with some preliminary measurements conducted on a NACA 0012 wing
Preliminary Solar Sail Design and Fabrication Assessment: Spinning Sail Blade, Square Sail Sheet
Blade design aspects most affecting producibility and means of measurement and control of length, scallop, fullness and straightness requirements and tolerances were extensively considered. Alternate designs of the panel seams and edge reinforcing members are believed to offer advantages of seam integrity, producibility, reliability, cost and weight. Approaches to and requirements for highly specialized metalizing methods, processes and equipment were studied and identified. Alternate methods of sail blade fabrication and related special machinery, tooling, fixtures and trade offs were examined. A preferred and recommended approach is also described. Quality control plans, inspection procedures, flow charts and special test equipment associated with the preferred manufacturing method were analyzed and are discussed
An atlas of 1975 GEOS-3 radar altimeter data for hurricane/tropical disturbance studies, volume 2
For abstract, see N77-24726
Ablation debris control by means of closed thick film filtered water immersion
The performance of laser ablation generated debris control by means of open immersion techniques have been shown to be limited by flow surface ripple effects on the beam and the action of ablation plume pressure loss by splashing of the immersion fluid. To eradicate these issues a closed technique has been developed which ensured a controlled geometry for both the optical interfaces of the flowing liquid film. This had the action of preventing splashing, ensuring repeatable machining conditions and allowed for control of liquid flow velocity. To investigate the performance benefits of this closed immersion technique bisphenol A polycarbonate samples have been machined using filtered water at a number of flow velocities. The results demonstrate the efficacy of the closed immersion technique: a 93% decrease in debris is produced when machining under closed filtered water immersion; the average debris particle size becomes larger, with an equal proportion of small and medium sized debris being produced when laser machining under closed flowing filtered water immersion; large debris is shown to be displaced further by a given flow velocity than smaller debris, showing that the action of flow turbulence in the duct has more impact on smaller debris. Low flow velocities were found to be less effective at controlling the positional trend of deposition of laser ablation generated debris than high flow velocities; but, use of excessive flow velocities resulted in turbulence motivated deposition. This work is of interest to the laser micromachining community and may aide in the manufacture of 2.5D laser etched patterns covering large area wafers and could be applied to a range of wavelengths and laser types
- …