Mini-BRU/BIPS foil bearing development

The analysis revealed the failure agent to be a combination of poor teflon coating adhesion, a decrease in bearing sway space and, possibly, lack of flushing flow through the bearing. A change in Teflon coating vendors provided substantially improved coating quality and surface finish. The sway space was increased and the cooling bleed flow was adjusted to flush the bearing. These changes were included in a test conducted in the WHL from 6 April to 22 May 1978 which resulted in the completion of 1006.9 hours of operation at temperature and load. Post-test inspection revealed the bearings to be in excellent condition and capable of completing a much longer test

Shuttle on-orbit contamination and environmental effects

Ensuring the compatibility of the space shuttle system with payloads and payload measurements is discussed. An extensive set of quantitative requirements and goals was developed and implemented by the space shuttle program management. The performance of the Shuttle system as measured by these requirements and goals was assessed partly through the use of the induced environment contamination monitor on Shuttle flights 2, 3, and 4. Contamination levels are low and generally within the requirements and goals established. Additional data from near-term payloads and already planned contamination measurements will complete the environment definition and allow for the development of contamination avoidance procedures as necessary for any payload

Silicon MINP solar cells

The MINP solar cell concept refers to a cell structure designed to be a base region dominated device. Thus, it is desirable that recombination losses are reduced to the point that they occur only in the base region. The most unique feature of the MINP cell design is that a tunneling contact is utilized for the metallic contact on the front surface. The areas under the collector grid and bus bar are passivated by a thin oxide of tunneling thickness. Efforts must also be taken to minimize recombination at the surface between grid lines, at the junction periphery and within the emitter. Results of both theoretical and experimental studies of silicon MINP cells are given. Performance calculations are described which give expected efficiencies as a function of base resistivity and junction depth. Fabrication and characterization of cells are discussed which are based on 0.2 ohm-cm substrates, diffused emitters on the order of 0.15 to 0.20 microns deep, and with Mg MIS collector grids. A total area AM 1 efficiency of 16.8% was achieved. Detailed analyses of photocurrent and current loss mechanisms are presented and utilized to discuss future directions of research. Finally, results reported by other workers are discussed

FARM-LEVEL RESPONSE TO AGRICULTURAL EFFLUENT CONTROL STRATEGIES: THE CASE OF THE WILLAMETTE VALLEY

This article examines economic incentives and other mechanisms to offset non-point source pollution from agriculture. A biophysical simulator to estimate technical relationships is linked to linear programming models for representative farms in the Willamette Valley of Oregon. The models are then optimized for profit maximization under alternative non-point pollution control policies. The results indicate that site-specific resource conditions and production possibilities greatly influence policy effectiveness and the cost of achieving pollution abatement. Nevertheless, some abatement is possible on all farms for relatively little cost.Environmental Economics and Policy,

Streak camera recording of shock wave transit times at large distances using laser illumination

A pulsed laser illumination system for streak camera recording of impact-induced shock wave transit times (~1 µs) during impact experiments is described. Laser illumination of centimeter-sized subjects offers many advantages over diffuse illumination techniques for streak photography. Source-to-sample and sample-to-camera distances of ~10^0 to 10^1 m can be employed. Light filtering, and simultaneous recording of both the impact event and the camera streak rate calibration, can be carried out easily. For use in such a system we describe a Pockels cell controller in which the reference 10-MHz oscillator signal is synchronously divided down to 38 Hz to provide a trigger signal for laser and streak camera testing

Regenerable adsorbent study

Thin film solid regenerable adsorbent for use with sorber plate to determine gase

Performance characteristics of the 12 GHz, 200 watt transmitter experiment package for CTS

The experiment package consists of a 200 W output stage tube (OST) powered by a power processing system (PPS). Descriptions of both the PPS and OST are given. The PPS provides the necessary voltages with a measured dc/dc conversion efficiency of 89 percent. The OST, a traveling wave tube with multiple collectors, has a saturated rf output power of 224 W and operates at an overall efficiency exceeding 40 percent over an 85 MHz bandwidth at 12 GHz. OST performance given includes frequency response, saturation characteristics, group delay, AM to PM conversion, inter-modulation distortion, and two channel gain suppression. Single and dual channel FM video performance is presented. It was determined that for 12 MHz peak to peak frequency deviation on each channel, dual channel FM television signals can be transmitted through the TEP at 60 W, each channel, with 40 MHz channel spacing (center to center)