Effect of polymerization cycles on gloss, roughness, hardness and impact strength of acrylic resins

The aim of this study was to evaluate the conventional and boiled polymerization cycles on gloss, roughness, hardness and impact strength of acrylic resins. Samples were made for each Classico and QC-20 materials (n=10) in dental stone molds obtained from rectangular metallic matrices embedded in metallic flasks. The powder-liquid ratio and manipulation of the acrylic resins' were accomplished according to manufacturers' instructions and the resins were conventionally packed in metallic flasks. After polymerization by (1) conventional: 74 °C for 9 h (Classico) and (2) boiled: 20 min (QC-20) cycles, the samples were deflasked after cooling at room temperature and conventionally finished and polished. The properties were evaluated after storage in water at 37 °C for 24 h. Gloss was verified with Multi Gloss 268 meter (Konica Minolta), surface roughness was measured with Surfcorder SE 1700 rugosimeter (Kosaka), Knoop hardness number was obtained with HMV-200 microdurometer, and impact strength was measured in an Otto Wolpert-Werke device by Charpy system (40 kpcm). Data were subjected to Student's t-test (at α=0.05). The results were: Gloss: 67.7 and 62.2 for Classico and QC-20 resins, respectively; Surface roughness: 0.874 and 1.469 Ra-µm for Classico and QC-20, respectively; Knoop hardness: 27.4 and 26.9 for Classico and QC-20, respectively; and Impact strength: 37.6 and 33.6 kgf/cm2 for Classico and QC-20, respectively. No statistically significant difference (p>0.05)were found between the resins for the evaluated properties. In conclusion, conventional and boiled polymerization cycles had similar effects on gloss, roughness, hardness and impact strength of both Classico and QC-20 resins272176180CONSELHO NACIONAL DE DESENVOLVIMENTO CIENTÍFICO E TECNOLÓGICO - CNPQSem informaçãoO propósito neste estudo foi avaliar os ciclos de polimerização convencional e por fervura sobre o brilho, rugosidade, dureza e resistência ao impacto de resinas acrílicas. Amostras foram confeccionadas para cada resina Clássico ou QC-20 (n=20) em moldes de gesso obtidos de matrizes metálicas retangulares incluídas em muflas metálicas. A proporção monômero/polímero das resinas e manipulação foram de acordo com as recomendações dos fabricantes e a massa convencionalmente incluída em muflas metálicas. Após polimerização nos ciclos (1) convencional: 74 °C por 9 horas (Clássico) e (2) fervura: 20 min (QC-20), as amostras foram demufladas após esfriadas em temperatura ambiente e convencionalmente acabadas e polidas. As propriedades foram avaliadas após armazenagem das amostras em água a 37 °C por 24 h. O brilho foi verificado com medidor Multi Gloss 268 (Konica Minolta), a rugosidade avaliada com rugosímetro Surfcorder SE 1700 (Kosaka), a dureza Knoop foi obtida com microdurômetro HMV-200 (Shimadzu) e a resistência ao impacto determinada pelo sistema Charpy (Otto Wolpert Werke). Os dados submetidos ao teste t de Student (α=0.05) mostraram que Os resultados foram: brilho: 67,7 e 62,2 para Clássico e QC-20, respectivamente; rugosidade: 0,874 e 1,469 Ra-µm para Clássico e QC-20, respectivamente; dureza: 27,4 e 26,9 para Clássico e QC-20, respectivamente; e resistência ao impacto: 37,6 e 33,6 kgf/cm2 para Clássico e QC-20, respectivamente. Não houve diference estatisticamente significante entre as resinas para as propriedades avaliadas. Conclui-se que os ciclos de polimerização convencional e por fervura promoveram similares efeitos sobre o brilho, rugosidade, dureza e resistência ao impacto para ambas as resinas Clássico e QC-2

Effect Of Ridge-lap Surface Treatments On The Bond Of Resin Teeth To Denture Base.

To test in vitro the shear bond strength of resin teeth to an acrylic resin denture base given different ridgelap surface treatments. Ninety rectangular dies were made with wax and traditionally invested in metallic or plastic flasks. The stone molds were covered with silicone, in which were included an acrylic molar with a wax stick fixed on the ridge lap surface. After deflasking, the wax sticks were removed, the teeth were cleaned with detergent, the ridge lap surface was submitted to different treatments (unmodified, bur-cut grooves, aluminum oxide particle sandblasting, monomer swelling, and primer swelling), and the teeth were replaced in the silicone molds. Metallic flasks were placed in a thermopolymerizing unit to polymerize heat-curing denture-base polymer, and plastic flasks were placed in a domestic microwave oven at 900 W to polymerize microwaveable denture base polymer. After deflasking, the specimens were submitted to the shear bond test in an Instron machine at a cross-speed of 1 mm/min. Results were submitted to ANOVA and Tukey's test (5%). Shear bond strength values were influenced by the ridge-lap surface treatments only in the microwaved polymer. Sandblasting + monomer swelling and sandblasting + primer swelling interactions yielded lower strengths for microwaved polymer. Only the unmodified surfaces presented a significant difference when the resins were compared, where the microwaved polymer showed a higher value. Different tooth ridge-lap surface treatments promoted different strengths of the tooth/resin bond.13287-9

Effect of Repeated Simulated Disinfections by Microwave Energy on the Complete Denture Base Adaptation

This study evaluated the effect of repeated microwave disinfections on the adaptation of the maxillar denture base using 2 different flask closure methods. Twenty stone cast-wax base sets were prepared for flasking by traditional cramp or RS system methods. Five bases for each method were submitted to 5 repeated simulated disinfections in a microwave oven with 650W for 3 minutes. Control bases were not disinfected. Three transverse cuts were made through each stone cast-resin base set, corresponding to canine, first molar, and posterior region. Measurements were made using an optical micrometer at 5 points for each cut to determine base adaptation: left and right marginal limits of the flanges, left and right ridge crests, and midline. Results for base adaptation performed by the flask closure methods were: traditional cramp (non-disinfected = 0.21 ± 0.05mm and disinfected = 0.22 ± 0.05mm), and RS system (non-disinfected = 0.16 ± 0.05 and disinfected = 0.17 ± 0.04mm). Collected data were submitted to ANOVA and Tukey test (α=.05). Repeated simulated disinfections by microwave energy did not cause deleterious effect on the base adaptation, when the traditional cramp and RS system flask closure methods were compared

Polymerization cycles on hardness and surface gloss of denture bases

The aim of this study was to evaluate different polymerization cycles on the hardness and surface gloss of acrylic resins for denture bases. Classico and Vip Cril Plus acrylic resins samples were made in dental stone molds. Powder-liquid ratio and resin manipulation were according to the manufacturers’ instructions, and the resulting mass pressed in metallic fl asks. The polymerization cycles were A - hot water bath at 74°C for 9 hours; B - hot water bath at 74°C for 8 hours + 100°C for 1 hour, and C - hot water bath at 74°C for 2 hours + 100°C for 1 hour. After polymerization, the samples were defl asked and submitted to finishing and polishing procedures, and stored in water at 37°C for 24 hours. A hardness indenter with load of 25 gf for 10 s evaluated the Knoop hardness values. A gloss meter evaluated the surface gloss using a light incidence of 60°. Data were submitted to ANOVA and Tukey’s test (α = 0.05). Hardness: There were signifi cant differences between resins regardless of polymerization cycles (Classico = 22.28 and Vip Cril Plus = 25.83). Significant differences occurred among polymerization cycles regardless of resins (A = 25.83, B = 24.64 and C = 21.73). There was similarity for the resin and cycle interaction (Classico: A = 24.51, B = 22.68 and C = 19.65; Vip Cril Plus: A = 27.15, B = 26.53 and C = 23.81). Surface gloss. Significant differences were shown between resins regardless of polymerization cycle (Classico = 57.26 and Vip Cril Plus = 49.38) and between polymerization cycles regardless of resin (A = 48.82, B = 53.46 and C = 57.68). Statistical diff erences were also found for the resin and cycle interaction (Classico: A = 52.32, B = 63.79 and C = 55.67; Vip Cril Plus: A = 45.32, B = 43.14 and C = 59.69). Diff erent polymerization cycles showed similar eff ects on hardness and different effects on the surface gloss of denture base acrylic resins

Cactus Cladodes Opuntia or Nopalea and By-Product of Low Nutritional Value as Solutions to Forage Shortages in Semiarid Areas

Simple Summary In the different livestock production systems, forage is the main feed resource. However, the availability and quality of the forage fluctuate throughout the year due to variable environmental conditions, such as temperature, humidity, location, or lack of rainfall. In semiarid regions, this fact is even more critical. The option for forage plants adapted to the semiarid climate, such as cactus cladodes, becomes indispensable for the sustainability of the systems. Nonetheless, it is necessary to combine the cactus with high-fiber-content feeds (silage, hay, and agroindustry residues, among others) to increase fiber contents in the diet to promote ideal rumen conditions. Based on the knowledge that cactus cladodes (Opuntia spp. and Nopalea spp.) are one of the most viable crops in semiarid regions, the association with a by-product rich in NDF proves to be a more feasible alternative in terms of price and availability, with the producer making the final decision. We aimed to evaluate the effect of the cactus cladodes Nopalea cochenillifera (L). Salm-Dyck. (NUB) and cactus cladodes Opuntia stricta (Haw.) Haw. (OUB), both combined with sugarcane bagasse (SB) plus urea, Tifton hay (TH), corn silage (CS), and sorghum silage (SS) plus urea on nutrient intake and digestibility, ruminal dynamics, and parameters. Five male sheep, fistulated in the rumen, were assigned in a 5 x 5 Latin square design. The NUB provided a higher intake of dry matter (DM) and any nutrients than SS. TH provided larger pools of DM and iNDF. The OUB and CS provided a higher DM degradation. CS provided a higher NDF degradation rate. OUB provided a lower ruminal pH. Depending on the collection time, the lowest pH value was estimated at 3.79 h after the morning feeding. There was an interaction between treatments and collection time on VFA concentrations. Due to the high degradation rate, greater energy intake, less change in rumen pH, greater volatile fatty acid production, and feasibility, we recommend using cactus associated with sugarcane bagasse plus urea in sheep diets

A Small Mammal Community in a Forest Fragment, Vegetation Corridor and Coffee Matrix System in the Brazilian Atlantic Forest

The objective of our work was to verify the value of the vegetation corridor in the conservation of small mammals in fragmented tropical landscapes, using a model system in the southeastern Minas Gerais. We evaluated and compared the composition and structure of small mammals in a vegetation corridor, forest fragments and a coffee matrix. A total of 15 species were recorded, and the highest species richness was observed in the vegetation corridor (13 species), followed by the forest fragments (10) and the coffee matrix (6). The absolute abundance was similar between the vegetation corridor and fragments (F = 22.94; p = 0.064), and the greatest differences occurred between the vegetation corridor and the matrix (F = 22.94; p = 0.001) and the forest fragments and the matrix (F = 22.94; p = 0.007). Six species showed significant habitat preference possibly related to the sensitivity of the species to the forest disturbance. Marmosops incanus was the species most sensitive to disturbance; Akodon montensis, Cerradomys subflavus, Gracilinanus microtarsus and Rhipidomys sp. displayed little sensitivity to disturbance, with a high relative abundance in the vegetation corridor. Calomys sp. was the species least affected by habitat disturbance, displaying a high relative abundance in the coffee matrix. Although the vegetation corridors are narrow (4 m width), our results support the hypothesis in which they work as a forest extension, share most species with the forest fragment and support species richness and abundance closer to forest fragments than to the coffee matrix. Our work highlights the importance and cost-effectiveness of these corridors to biodiversity management in the fragmented Atlantic Forest landscapes and at the regional level