Computer code for predicting coolant flow and heat transfer in turbomachinery

A computer code was developed to analyze any turbomachinery coolant flow path geometry that consist of a single flow passage with a unique inlet and exit. Flow can be bled off for tip-cap impingement cooling, and a flow bypass can be specified in which coolant flow is taken off at one point in the flow channel and reintroduced at a point farther downstream in the same channel. The user may either choose the coolant flow rate or let the program determine the flow rate from specified inlet and exit conditions. The computer code integrates the 1-D momentum and energy equations along a defined flow path and calculates the coolant's flow rate, temperature, pressure, and velocity and the heat transfer coefficients along the passage. The equations account for area change, mass addition or subtraction, pumping, friction, and heat transfer

Small gas turbine engine technology

Performance of small gas turbine engines in the 250 to 1,000 horsepower size range is significantly lower than that of large engines. Engines of this size are typically used in rotorcraft, commutercraft, general aviation, and cruise missile applications. Principal reasons for the lower efficiencies of a smaller engine are well known: component efficients are lower by as much as 8 to 10 percentage points because of size effects. Small engines are designed for lower cycle pressures and temperatures because of smaller blading and cooling limitations. The highly developed analytical and manufacturing techniques evolved for large engines are not directly transferrable to small engines. Thus, it was recognized that a focused effort addressing technologies for small engies was needed and could significantly impact their performance. Recently, in-house and contract studies were undertaken at the NASA Lewis Research Center to identify advanced engine cycle and component requirements for substantial performance improvement of small gas turbines for projected year 2000 applications. The results of both in-house research and contract studies are presented. In summary, projected fuel savings of 22 to 42 percent could be obtained. Accompanying direct operating cost reductions of 11 to 17 percent, depending on fuel cost, were also estimated. High payoff technologies are identified for all engine applications, and recent results of experimental research to evolve the high payoff technologies are described

Overcoming Present-Day Powerplant Limitations Via Unconventional Engine Configurations

The Army Research Laboratory s Vehicle Technology Directorate is sponsoring the prototype development of three unconventional engine concepts - two intermittent combustion (IC) engines and one turbine engine (via SBIR (Small Business Innovative Research) contracts). The IC concepts are the Nutating Engine and the Bonner Engine, and the turbine concept is the POWER Engine. Each of the three engines offers unique and greatly improved capabilities (which cannot be achieved by present-day powerplants), while offering significant reductions in size and weight. This paper presents brief descriptions of the physical characteristics of the three engines, and discusses their performance potentials, as well as their development status

The Nutating Engine-Prototype Engine Progress Report and Test Results

A prototype of a new, internal combustion (IC) engine concept has been completed. The Nutating Engine features an internal disk nutating (wobbling) on a Z-shaped power shaft. The engine is exceedingly compact, and several times more power dense than any conventional (reciprocating or rotary) IC engine. This paper discusses lessons learned during the prototype engine's development and provides details of its construction. In addition, results of the initial performance tests of the various components, as well as the complete engine, are summarized

Procedure for Determining One-Dimensional Flow Distributions in Arbitrarily Connected Passages Without the Influence of Pumping

A calculation procedure is presented which allows the one-dimensional determination of flow distributions in arbitrarily connected (branching) flow passages having multiple inlets and exits. The procedure uses an adaptation of the finite element technique, iteratively coupled with an accurate one-dimensional flow solver. The procedure eliminates the usual restrictions inherent with finite element flow calculations. Unlike existing one-dimensional methods, which require simplifications to the flow equations (uncoupling the momentum and energy equations), to allow for arbitrary branching and multiple inlets and exits, the only limitation of the described methodology is that, at present, it can only accommodate non-rotating configurations (no pumping effects). The calculation procedure is robust, and will always converge for physically possible flow. The procedure is described, and its use is illustrated by an example

SYSTEM DESIGN OF A NOVEL COMBINED COOLING, HEAT, POWER, AND WATER MICROTURBINE COMBINED CYCLE

ABSTRACT The Power, Water Extraction, and Refrigeration (PoWER) engine has been investigated for several years as a distributed energy system, among other applications, for civilian or military use. Previous literature describing its modeling and experimental demonstration have indicated several benefits, especially when the underlying semi-closed cycle gas turbine is combined with a vapor absorption refrigeration system, the PoWER system described herein. The benefits include increased efficiency, high part-power efficiency, small lapse rate, compactness, less emissions, less air and exhaust flows (which decrease filtration and duct size) and condensation of fresh water. The current paper describes the preliminary design and modeling of a modified version of this system as applied to distributed energy, especially useful in regions which are prone to major grid interruptions due to hurricanes, undercapacity, or terrorism. In such cases, the distributed energy system should support most or all services within an isolated service island, including ice production, so that the influence of the power outage is limited in scope. The current paper describes the rather straightforward system modifications necessary for ice production. The primary focus of the paper is the use of this ice-making capacity to achieve significant loadleveling during the summer utility peak, hence reducing the electrical capacity requirements for the grid as well as loadleveling strategies