Variaciones fisiológicas observadas en tubérculos de patata (solanum tuberosum L.) después de un tratamiento con radiación gamma

Tesis inédita de la Universidad Complutense de Madrid, Facultad de Ciencias Químicas, leída en 1975.Fac. de Ciencias QuímicasTRUEProQuestpu

Biomechanical effects of a new macrogeometry design of dental implants: an in vitro experimental analysis

The purpose of the present study was to measure and compare the insertion torque, removal torque, and the implant stability quotient by resonance frequency analysis in different polyurethane block densities of two implant macrogeometries. Four different polyurethane synthetic bone blocks were used with three cortical thickness: Bone 1 with a cortical thickness of 1 mm, Bone 2 with a cortical thickness of 2 mm, Bone 3 with a cortical thickness of 3 mm, and Bone 4, which was totally cortical. Four groups were created in accordance with the implant macrogeometry (n = 10 per group) and surface treatment: G1—regular implant design without surface treatment; G2—regular implant design with surface treatment; G3—new implant design without surface treatment; G4—new implant design with surface treatment. All implants used were 4 mm in diameter and 10 mm in length and manufactured in commercially pure titanium (grade IV) by Implacil De Bortoli (São Paulo, Brazil). The implants were installed using a computed torque machine, and following installation of the implant, the stability quotient (implant stability quotient, ISQ) values were measured in two directions using Osstell devices. The data were analyzed by considering the 5% level of significance. All implant groups showed similar mean ISQ values without statistical differences (p > 0.05), for the same synthetic bone block: for Bone 1, the value was 57.7 ± 3.0; for Bone 2, it was 58.6 ± 2.2; for Bone 3, it was 60.6 ± 2.3; and for Bone 4, it was 68.5 ± 2.8. However, the insertion torque showed similar higher values for the regular macrogeometry (G1 and G2 groups) in comparison with the new implant macrogeometry (G3 and G4 groups). The analysis of the results found that primary stability does not simply depend on the insertion torque but also on the bone quality. In comparison with the regular implant macrogeometry, the new implant macrogeometry decreased the insertion torque without affecting the implant stability quotient values

Variaciones fisiológicas observadas en tubérculos de patata (solanum tuberosum L.) después de un tratamiento con radiación gamma

Tesis inédita de la Universidad Complutense de Madrid, Facultad de Ciencias Químicas, leída en 1975.Fac. de Ciencias QuímicasTRUEProQuestpu

Osteitis condensante de clavícula

La osteítis condensante de clavícula es una lesión ósea infrecuente, benigna y de etiología desconocida. Se caracteriza por esclerosis densa y homogénea de la porción infero-medial clavicular con obliteración de la cavidad medular sin afectación de la articulación esternoclavicular. Hasta ahora sólo se había descrito en mujeres, en el presente trabajo presentamos un caso en un paciente varón. Se discute el diagnóstico diferencial con otras entidades que producen afectación similar y proponemos la TC como método diagnóstico de elección, defendiendo el tratamiento conservador.Condensing osteitis of the clavicle is a benign and uncommon bone lesion of unknown cause, characterized by homogeneously dense sclerotic patch with obliteration of the marrow cavity at the medial end of the clavicle without involvement of the sternoclavicular joint. To date it had been described only in women. In this work we report a case in a male patient. The differential diagnosis with other disorders of similar findings is discussed. We propose CT-scan as the elective diagnostic test and we defend the conservative treatment

Study of two bovine bone blocks (sintered and non-sintered) used for bone grafts: physico-chemical characterization and in vitro bioactivity and cellular analysis

High-temperature compression and electron backscatter diffraction (EBSD) techniques were used in a systematic investigation of the dynamic recrystallization (DRX) behavior and texture evolution of the Inconel625 alloy. The true stress–true strain curves and the constitutive equation of Inconel625 were obtained at temperatures ranging from 900 to 1200 °C and strain rates of 10, 1, 0.1, and 0.01 s−1. The adiabatic heating effect was observed during the hot compression process. At a high strain rate, as the temperature increased, the grains initially refined and then grew, and the proportion of high-angle grain boundaries increased. The volume fraction of the dynamic recrystallization increased. Most of the grains were randomly distributed and the proportion of recrystallized texture components first increased and then decreased. Complete dynamic recrystallization occurred at 1100 °C, where the recrystallized volume fraction and the random distribution ratios of grains reached a maximum. This study indicated that the dynamic recrystallization mechanism of the Inconel625 alloy at a high strain rate included continuous dynamic recrystallization with subgrain merging and rotation, and discontinuous dynamic recrystallization with bulging grain boundary induced by twinning. The latter mechanism was less dominan

Aplasia parcial congénita de arco posterior de atlas.

Los defectos de arco posterior de C1 son anomalías raras pero bien documentadas en la bibliografía, la mayoría de los casos son asintomáticos pero existen casos publicados de mielopatía y tetraparesia transitoria asociadas a defectos de arco posterior de atlas. Se presentan dos casos: una mujer de 31 años que presentó cérvico-braquialgia secundaria a accidente de tráfico en la que se detectó aplasia parcial de arco posterior de atlas que un año después continúa con dolor y un paciente de 28 años que sufrió accidente de tráfico en la que se detectó aplasia parcial de arco posterior de atlas. Se realiza una revisión bibliográfica.Partial aplasia of posterior arch of the atlas are rare but well documented anomalies, most cases are asymp- tomatic but cases of myelopaty and quadraparesis associa- ted to defects of posterior arch of the atlas have been publis- hed in the past. Case 1: female, 31 years old, suffered traffic accident with neck and upper limb pain. Partial aplasia of posterior arch to the atlas was detected in X-Rays, at the moment the patient continues with neck pain. Case 2: female 28 years old who referred neck pain after traffic accident, partial aplasia of posterior arch of the atlas was detected. Bibliographic review

Prevalence and Prognostic Influence of Peripheral Arterial Disease in Patients ≥40 Years Old Admitted into Hospital Following an Acute Coronary Event

AbstractObjectiveA significant proportion of patients with ischemic heart disease have associated peripheral arterial disease (PAD), but many are asymptomatic and this condition remains underdiagnosed. We aimed to study the prevalence of PAD in patients with an acute coronary syndrome (ACS) and to evaluate its influence in hospital clinical outcomes.MethodsThe PAMISCA register is a prospective, multicenter study involving patients ≥40 years old with ACS admitted to selected Spanish hospitals. All patients had their ankle-brachial index (ABI) measured between days 3 and 7 after the ischemic event.Results1410 ACS patients (71.4% male) were included. PAD determined by ABI was documented in 561 patients (39.8%). Factors independently related to PAD were age (OR: 1.04; 95% CI: 1.03–1.06; p<0.001), smoking (OR: 1.88; 95% CI: 1.41–2.49; p<0.0001), diabetes (OR: 1.30; 95% CI: 1.02–1.65; p<0.05), previous cardiac disease (OR: 1.54; 95% CI: 1.22–1.95; p<0.001) and previous cerebrovascular disease (OR: 1.90; 95% CI: 1.28–2.80; p<0.001). Following the ACS, an ABI≤0.90 was associated with increased cardiovascular mortality (OR: 5.45; 95% CI: 1.16–25.59; p<0.05) and a higher risk of cardiovascular complications.ConclusionThe prevalence of PAD in patients ≥40 years presenting with ACS is high and it is associated with increased cardiovascular risk

Biomechanical and histological analysis of titanium (machined and treated surface) versus zirconia implant materials: an in vivo animal study

This article belongs to the Special Issue Clinical Implants and the Biocompatibility of Biodegradable BiomaterialsObjectives: The aim of this study was to perform an in vivo histological comparative evaluation of bone formation around titanium (machined and treated surface) and zirconia implants. For the present study were used 50 commercially pure titanium implants grade IV, being that 25 implants with a machined surface (TiM group), 25 implants with a treated surface (TiT group) and, 25 implants were manufactured in pure zirconia (Zr group). The implants (n = 20 per group) were installed in the tibia of 10 rabbits. The implants distribution was randomized (n = 3 implants per tibia). Five implants of each group were analyzed by scanning electron microscopy and an optical laser profilometer for surface roughness characterization. Six weeks after the implantation, 10 implants for each group were removed in counter-torque for analysis of maximum torque value. The remaining samples were processed, included in historesin and cut to obtain non-decalcified slides for histomorphological analyses and histomorphometric measurement of the percentage of bone-implant contact (BIC%). Comparisons were made between the groups using a 5% level of significance (p < 0.05) to assess statistical differences. The results of removal torque values (mean ± standard deviation) showed for the TiM group 15.9 ± 4.18 N cm, for TiT group 27.9 ± 5.15 N cm and for Zr group 11.5 ± 2.92 N cm, with significant statistical difference between the groups (p < 0.0001). However, the BIC% presented similar values for all groups (35.4 ± 4.54 for TiM group, 37.8 ± 4.84 for TiT group and 34.0 ± 6.82 for Zr group), with no statistical differences (p = 0.2171). Within the limitations of the present study, the findings suggest that the quality of the new bone tissue formed around the titanium implants present a superior density (maturation) in comparison to the zirconia implants