204 research outputs found
Evaluation of pressure and temperature effect on the structure and properties of Ca2.93Sr0.07Co4O9 ceramic materials
In this work, the effect of hot-pressing conditions on the performances of Sr-doped Ca3Co4O9 materials has been investigated. The samples were prepared from attrition milled precursors, which reduced the processing time. Samples were hot-pressed at temperatures (T) between 800 and 900 °C and pressures (P) from 51 to 71 MPa. The out-of-plane X-ray diffraction (XRD) showed that all samples are formed by the thermoelectric phase, with a good grain orientation which is improved with T, and P, as demonstrated by their Lotgering factor. The observations through Scanning Electron Microscopy (SEM) have revealed that grain sizes and orientation are enhanced with T, and P, as well as density through Archimedes''s method. All these trends are reflected in the flexural strength and microhardness. The electrical resistivity is lower when the T, or P, is increased, reaching 6.4 mO cm for samples processed at 900 °C and 71 MPa, which is about the best reported values in the literature. On the other hand, contrarily to the expected results, they also showed the highest S values, 182 µV/K, which are similar to the best reported values for highly dense textured materials. Thermal conductivity values do not follow a regular evolution with the hot-pressing conditions, probably due to internal stresses, reaching the lowest values at 800 °C in samples processed at 800 °C and 51 MPa (1.51 W/(K*m)) or 900 °C and 61 MPa (1.53 W/(K*m)). Consequently, the highest ZT values have been determined in samples processed at 900 °C and 61 MPa (0.35) which is higher than the best reported values in literature for bulk textured samples, to the best of our knowledge. © 2021 The Author
Tuning Ca3Co4O9 thermal and transport properties by TiC nanoparticles addition
Ca3Co4O9 + xwt.% TiC (x = 0, 0.25, 0.5, 0.75, and 1.0) polycrystalline thermoelectric ceramics have been prepared through the classical ceramic route. XRD characterization has demonstrated that all samples are mainly composed by the Ca3Co4O9 phase, while microstructural observation has shown that no reaction between both components has been produced. Moreover, TiC particles are well distributed for small additions, and start to agglomerate from 0.75 wt.% content. Density measurements showed that nearly no changes have been produced by TiC addition and nearly the whole porosity appears as open one. Furthermore, electrical resistivity decreases up to 0.75 wt.% addition, increasing for higher content. On the other hand, Seebeck coefficient has been maintained unchanged in all samples. In spite of an irregular behaviour of thermal conductivity with temperature, it tends to decrease when the temperature is raised, displaying the lowest values for the 0.25 wt.% samples. These data led to an increase of about 40% in ZT values at 800 °C for samples with 0.25 wt.% addition, when compared with the pure ones. Finally, linear thermal expansion coefficient is decreased when TiC content is increased, which can be exploited to fit the thermal expansion coefficients of all the components used to build a power generation thermoelectric module
Growth and texture of Spark Plasma Sintered Al2O3 ceramics: a combined analysis of X-rays and Electron Back Scatter Diffraction
Textured alumina ceramics were obtained by Spark Plasma Sintering (SPS) of
undoped commercial a-Al2O3 powders. Various parameters (density, grain growth,
grain size distribution) of the alumina ceramics, sintered at two typical
temperatures 1400{\deg}C and 1700{\deg}C, are investigated. Quantitative
textural and structural analysis, carried out using a combination of Electron
Back Scattering Diffraction (EBSD) and X-ray diffraction (XRD), are represented
in the form of mapping, and pole figures. The mechanical properties of these
textured alumina ceramics include high elastic modulus and hardness value with
high anisotropic nature, opening the door for a large range of applicationsComment: 16 pages, 6 figures, submitted to J. Appl. Phy
Recommended from our members
Low temperature synthesis and spark plasma sintering of a boron carbide with a low residual carbon content
Supplementary data available online at: https://www.sciencedirect.com/science/article/pii/S0955221921007214?via%3Dihub#sec0075 .Using spark plasma sintering (SPS), >98.5 % dense boron carbide (B4C) samples were made from commercially available and lab-synthesised powders made via a low temperature synthesis (LTS) process. The work showed that the LTS powder can be produced in batches of tens to hundreds of grams whilst maintaining a high purity material with lower levels of residual free carbon (20.6–21.3 wt.% C) than commercially available samples (22.4 wt.% C). The LTS material was seen to exhibit higher hardness values (37.8 GPa) than the commercial grade material (32.5 GPa) despite featuring a coarser average grain size (10.8 μm and 2.4 μm respectively). This is largely thought to be due to the influence of ZrO2 and AlB2 impurities introduced to the material during micronising milling of the powder after synthesis, as opposed to the influence of the materials lower carbon content.UK-France PhD scheme (grant no: DSTLX- 1000092033)
Experimental evidence for an intermediate phase in the multiferroic YMnO3
We have studied YMnO by high-temperature synchrotron X-ray powder
diffraction, and have carried out differential thermal analysis and dilatometry
on a single crystal sample. These experiments show two phase transitions at
about 1100K and 1350K, respectively. This demonstrates the existence of an
intermediate phase between the room temperature ferroelectric and the high
temperature centrosymmetric phase. This study identifies for the first time the
different high-temperature phase transitions in YMnO.Comment: 10 pages 5 figures. New version, Additional data, Journal of Physics:
Condensed Matter, in Pres
UTILIZING CASSAVA STARCH AND POWDERED RICE BRAN IN MAKING BIODEGRADABLE STRAWS
Numerous agricultural wastes are impractically discarded every day, and one of these is rice bran. This study investigated the production of a biodegradable straw made of cassava starch and powdered rice bran. It aimed to determine the effectiveness of the different treatments of Cassava Starch-Rice Bran in terms of water resistance, tensile strength, and biodegradability. An experimental design was used in conducting the study. There were three treatments made in making CSRB straws: the first, with more rice bran; the second, with the same cassava starch and rice bran ratio; and the third, with more cassava starch. These treatments produced three replicates each. The straws were placed in a dehydrating machine for 24 hours at a temperature of 60° Celsius. The straws were then coated with beeswax after being removed from their respective molders. The CSRB straws were found to be water resistant due to the beeswax coating applied, although it had a weak tensile strength even with the presence of beeswax. The rate of biodegradability of the CSRB straw was fast due to it being made up of organic materials. The results revealed that straws made from Cassava Starch and Powdered Rice Bran are effective in terms of water resistance and biodegradability
English in product advertisements in non-english speaking countries in western europe: Product image and comprehension of the text
Although English has been shown to be the most frequently used foreign language in product advertisements in countries where it is not the native language, little is known about its effects. This article examines the response to advertisements in English compared to the response to the same ad in the local language in Western Europe on members of the target group for which the ad was intended: 715 young, highly educated female consumers. The use of English in a product ad does not appear to have any impact on image and price of the product, but it does affect text comprehension: the meaning of almost 40% of the English phrases was not understood. These results were the same for all countries involved in the study, irrespective of whether the respondents\u27 (self-) reported proficiency in English is high or low. © Taylor & Francis Group, LLC
- …