626 research outputs found
Electronic Properties of CdS/CdTe Solar Cells as Influenced by a Buffer Layer
We considered modification of the defect density of states in CdTe as influenced by a buffer layer in ZnO(ZnS, SnSe)/CdS/CdTe solar cells. Compared to the solar cells employing ZnO buffer layers, implementation of ZnSe and ZnS resulted in the lower net ionized acceptor concentration and the energy shift of the dominant deep trap levels to the midgap of CdTe. The results clearly indicated that the same defect was responsible for the inefficient doping and the formation of recombination centers in CdTe. This observation can be explained taking into account the effect of strain on the electronic properties of the grain boundary interface states in polycrystalline CdTe. In the conditions of strain, interaction of chlorine with the grain boundary point defects can be altered
Comparison of one and two-stage growth approaches for close space sublimation deposition of Sb<inf>2</inf>Se<inf>3</inf> thin film solar cells
In this work, we investigate the impact of grain structure and ribbon orientation on Sb2Se3 solar cells deposited by close space sublimation (CSS). Films of Sb2Se3 were produced using either a single-stage low-temperature “seed-layer” deposition, a high-temperature “growth-layer” deposition, or a combined two-stage deposition process combining both “seed” and “growth” layers. This study demonstrates the essential nature of the “seed” layer to achieve the required substrate coverage and ensure functioning Sb2Se3 solar cells by this technique. A photovoltaic efficiency of 5.07 % was obtained by fabricating solar cells with a two-stage Sb2Se3 growth process using the structure (FTO/TiO2/Sb2Se3/P3HT/Au) in superstrate configuration. Comparisons were made between device performance and ribbon orientation assessed by XRD measurements via a ribbon carrier transport (RCT) analysis method, as well as with surface coverage and grain size. The addition of a second growth stage was found to result in a more vertical ribbon orientation compared to a single low temperature deposition, however predominantly controls the overall surface coverage. We observe no obvious links between the orientation of ribbons and the cell performance. Instead we propose that the performance, and in particular the device VOC, is more strongly determined by the overall grain structure rather than simply by the ribbon orientation
Ultrasensitive force and displacement detection using trapped ions
The ability to detect extremely small forces is vital for a variety of
disciplines including precision spin-resonance imaging, microscopy, and tests
of fundamental physical phenomena. Current force-detection sensitivity limits
have surpassed 1 (atto ) through coupling of micro or
nanofabricated mechanical resonators to a variety of physical systems including
single-electron transistors, superconducting microwave cavities, and individual
spins. These experiments have allowed for probing studies of a variety of
phenomena, but sensitivity requirements are ever-increasing as new regimes of
physical interactions are considered. Here we show that trapped atomic ions are
exquisitely sensitive force detectors, with a measured sensitivity more than
three orders of magnitude better than existing reports. We demonstrate
detection of forces as small as 174 (yocto ), with a
sensitivity 390 using crystals of Be
ions in a Penning trap. Our technique is based on the excitation of normal
motional modes in an ion trap by externally applied electric fields, detection
via and phase-coherent Doppler velocimetry, which allows for the discrimination
of ion motion with amplitudes on the scale of nanometers. These experimental
results and extracted force-detection sensitivities in the single-ion limit
validate proposals suggesting that trapped atomic ions are capable of detecting
of forces with sensitivity approaching 1 . We anticipate that
this demonstration will be strongly motivational for the development of a new
class of deployable trapped-ion-based sensors, and will permit scientists to
access new regimes in materials science.Comment: Expanded introduction and analysis. Methods section added. Subject to
press embarg
Band gap temperature-dependence of close-space sublimation grown Sb2Se3 by photo-reflectance
The candidate photovoltaic absorber antimony selenide Sb2Se3 has been prepared by the commercially attractive close-space sublimation method. Structure, composition, and morphology are studied by x-ray diffraction, scanning electron microscopy, and energy dispersive spectroscopy. Large rhubarb-like grains favorable for photovoltaics naturally develop. The temperature-dependence of the direct band gap is determined by photoreflectance between 20 and 320 K and is well described by the Varshni and Bose–Einstein relations, blue-shifting with decreasing temperature from 1.18 to 1.32 eV. The 300 K band gap matches that seen in high quality single-crystal material, while the 0 K gap is consistent with that found in first-principles calculations, further supporting the array of beneficial photovoltaic properties indicated for this material
Benchmark performance of low-cost Sb2Se3 photocathodes for unassisted solar overall water splitting
Determining cost-effective semiconductors exhibiting desirable properties for commercial photoelectrochemical water splitting remains a challenge. Herein, we report a Sb2Se3 semiconductor that satisfies most requirements for an ideal high-performance photoelectrode, including a small band gap and favourable cost, optoelectronic properties, processability, and photocorrosion stability. Strong anisotropy, a major issue for Sb2Se3, is resolved by suppressing growth kinetics via close space sublimation to obtain high-quality compact thin films with favourable crystallographic orientation. The Sb2Se3 photocathode exhibits a high photocurrent density of almost 30mAcm(-2) at 0V against the reversible hydrogen electrode, the highest value so far. We demonstrate unassisted solar overall water splitting by combining the optimised Sb2Se3 photocathode with a BiVO4 photoanode, achieving a solar-to-hydrogen efficiency of 1.5% with stability over 10h under simulated 1 sun conditions employing a broad range of solar fluxes. Low-cost Sb2Se3 can thus be an attractive breakthrough material for commercial solar fuel production. While photoelectrochemical water splitting offers an integrated means to convert sunlight to a renewable fuel, cost-effective light-absorbers are rare. Here, authors report Sb2Se3 photocathodes for high-performance photoelectrochemical water splitting devices
- …