Détermination en milieu naturel du dioxide de chlore, des ions chlorite et chlorate basée sur l'utilisation du carmin indigo: étude des interférences

Différentes méthodes fondées sur l'exploitation d'un même réactif à savoir le carmin indigo ont été mises en œuvre pour réaliser le suivi du dioxyde de chlore et des sous-produits de dégradation que sont les ions chlorite et chlorate.L'étude de la stabilité du carmin indigo a permis de montrer que la détermination du dioxyde de chlore doit être effectuée dans les premières heures qui suivent l'ajout de carmin indigo, une légère diminution de l'absorbance étant observée au delà de vingt heures. L'absorbance du carmin indigo en présence d'ions chlorite et chlorate reste en revanche stable plusieurs jours.La recherche d'éventuelles interférences (substances humiques, ozone, hypochlorite) a également été effectuée. Les ions chlorite et chlorate réagissent avec les substances humiques en milieu acide selon une cinétique réactionnelle beaucoup plus lente que celle des ions chlorite et chlorate sur le carmin indigo. De ce fait, les pourcentages d'erreur sur les concentrations restent faibles. L'hypochlorite ou plus précisément l'acide hypochloreux réagit avec le carmin indigo ce qui conduit à des erreurs dans la détermination du dioxyde de chlore, des ions chlorite et chlorate. Dans le cas du dosage du dioxyde de chlore, les sources d'erreur peuvent être éliminées en ajoutant de l'ammoniaque avant l'introduction du carmin indigo dans l'échantillon.Après avoir été validés dans des milieux synthétiques, les protocoles ont été appliqués à un milieu naturel : l'eau de distribution de la ville de Brest. Une analyse statistique a été effectuée dans le but de comparer les résultats avec ceux déduits d'autres méthodes basées sur des principes différents.Over the last decade, chlorine dioxide has been increasingly used for disinfecting drinking water in many countries. A guarantee for the protection of the consumer is the presence of a sufficient residual concentration of the bactericidal reagent in drinking water. Thus it is important to determine exactly and accurately the levels of chlorine dioxide at the tap. During water treatment and subsequent distribution, chlorine dioxide can undergo a variety of reduction and disproportionation reactions producing primarily chloride but also chlorite and chlorate, which have been shown to cause haemolytic anemia. Reliable analytical methods are needed to identify and determine levels of chlorine dioxide, chlorite and chlorate in drinking water. A procedure based on the use of indigo carmine for the determination of each species in natural waters is suggested in this paper.In phosphate buffer (pH 6.8), two moles of chlorine dioxide oxidize one mole of indigo carmine. The concentration of the bactericidal reagent can be determined by measuring the difference in absorbance of the dye at 610 nm before and after reaction with chlorine dioxide. This method is selective as chlorite and chlorate do not react with indigo carmine in phosphate buffer at pH 6.8. Although the spectrophotometric method can be used successfully used at levels of chlorine dioxide down to 30 µg/l, the determination of lower levels in tap water requires a more sensitive method such as an electrochemical stripping procedure. This analysis is based on the measurement of the decrease in the indigo carmine signal after addition of chlorine dioxide. The detection limit is around 1 µg/l.At pH=2, one mole of indigo carmine reduces one mole of chlorite. Thus the chlorite concentration can be determined by measuring the indigo carmine absorbance at pH=2. At pH=0, indigo carmine reacts with both chlorite and chlorate. A measurement at pH=0 allows chlorate concentrations to be determined since the decrease in absorbance due to the presence of chlorite can be calculated.The stability of indigo carmine absorbance has been studied. An indigo carmine solution prepared in phosphate buffer is stable over several days if kept in light-proof bottles. It is not surprising that the presence of chlorite and chlorate does not lead to a change in absorbance as they do not react with the dye at pH=6.8. A slight decrease in absorbance of an indigo carmine solution containing chlorine dioxide is observed after about twenty hours. This means that the chlorine dioxide concentration has to be determined in the first hours, which follow the addition of the dye to the sample in order to avoid errors.Interferences can arise from other residual oxidants, which may also be used in water treatment, or from substances present in the sample, which may react with indigo carmine, chlorite and chlorate. Accordingly, we have considered the influence of humic substances, ozone and hypochlorite. The absorbance of indigo carmine at pH=2 and at pH=0 does not change in presence of natural organic matter (1 mg/l). Chlorite and chlorate react with humic substances but the kinetics are much slower than those of the reactions with indigo carmine. Errors arising from humic substances in chlorite and chlorate measurements are thus very weak. Ozone may interfere in analyses as it reacts with indigo carmine. However its existence in the distribution network is unlikely as it also reacts with chlorine dioxide, which is in excess, and chlorite to give chlorate. Hypochlorite causes errors in chlorine dioxide, chlorite and chlorate determinations as a result of a reaction with indigo carmine. In the case of chlorine dioxide determinations, errors can be eliminated by adding ammonia to the sample before indigo carmine.Once the validity of the procedures had been proven in synthetic media, the methods were applied to a natural water, that of the water distribution network of the city of Brest, France. The results have been compared with those of other analytical techniques

Covalent vs. non-covalent redox functionalization of C-LiFePO4 based electrodes

During high rate utilization of porous Li battery, Li+ refuelling from the electrolyte limits the discharge kinetics of positive electrodes. In the case of thick electrodes a strategy to buffer the resulting sharp drop of Li+ concentration gradient would be to functionalize the electrode with anionic based redox molecules (RMR) that would be therefore able to relay intercalation process. The occurrence of these RMR in the electrode should not however, induce adverse effect on Li intercalation processes. In this respect, this work studies the effect of functionalizing LFPC based electrodes by either covalent or non-covalent chemistry, on Li intercalation kinetics. To do so, model molecules containing a nitro group were introduced at the surface of both carbon conducting additives and active material (C-LiFePO4). It is shown that presumably due to formation of sp(3) defects, covalent anchoring using diazonium chemistry inhibits the intercalation kinetics in C-FePO4. On the contrary, if molecules such as pyrene derivatives are immobilized by pi-staking interactions, Li intercalation is not impeded. Therefore non-covalent functionalization of pyrene based RMR appears as a promising route to relay Li intercalation reaction during high power demand. The framework for future development of this strategy is discussed. (C) 2013 Elsevier B.V. All rights reserved

In situ redox functionalization of composite electrodes for high power-high energy electrochemical storage systems via a non-covalent approach

The growing demand for new global resources of clean and sustainable energy emerges as the greatest challenge in today\u27s society. For numerous applications such as hybrid vehicles, electrochemical storage systems simultaneously require high energy and high power. For this reason, intensive researches focus on proposing alternative devices to conventional Li battery and supercapacitors. Here, we report a proof of concept based on non-covalent redox functionalization of composite electrodes that may occur either during the calendar life or during the device functioning. The active material, a multi-redox pyrene derivative, is initially contained in the electrolyte. No additional benchmarking step is therefore required, and it can, in principle, be readily applied to any type of composite electrode (supercapacitors, battery, semi-solid flow cell etc.). Accordingly, a practical carbon fiber electrode that is 10 mg cm(-2) loaded can deliver up to 130 kW kg(electrode)(-1) and 130 Wh kg(electrode)(-1) with negligible capacity loss over the first 60 000 charge/discharge cycles

New Concept to Boost Energy and Power Peformance of Practical Electrochemical Devices

International audienc

New concept and electrochemistry of in situ non-covalent immobilization of redox molecules for energy storage applications

International audienc

The GOODSTEP project: General Object-Oriented Database for Software Engineering Processes

The goal of the GOODSTEP project is to enhance and improve the functionality of a fully object-oriented database management system to yield a platform suited for applications such as software development environments (SDEs). The baseline of the project is the O2 database management system (DBMS). The O2 DBMS already includes many of the features regulated by SDEs. The project has identified enhancements to O2 in order to make it a real software engineering DBMS. These enhancements are essentially upgrades of the existing O2 functionality, and hence require relatively easy extensions to the O2 system. They have been developed in the early stages of the project and are now exploited and validated by a number of software engineering tools built on top of the enhanced O2 DBMS. To ease tool construction, the GOODSTEP platform encompasses tool generation capabilities which allow for generation of integrated graphical and textual tools from high-level specifications. In addition, the GOODSTEP platform provides a software process toolset which enables modeling, analysis and enaction of software processes and is also built on top of the extended O2 database. The GOODSTEP platform is to be validated using two CASE studies carried out to develop an airline application and a business application

Variational assimilation of Lagrangian data in oceanography

We consider the assimilation of Lagrangian data into a primitive equations circulation model of the ocean at basin scale. The Lagrangian data are positions of floats drifting at fixed depth. We aim at reconstructing the four-dimensional space-time circulation of the ocean. This problem is solved using the four-dimensional variational technique and the adjoint method. In this problem the control vector is chosen as being the initial state of the dynamical system. The observed variables, namely the positions of the floats, are expressed as a function of the control vector via a nonlinear observation operator. This method has been implemented and has the ability to reconstruct the main patterns of the oceanic circulation. Moreover it is very robust with respect to increase of time-sampling period of observations. We have run many twin experiments in order to analyze the sensitivity of our method to the number of floats, the time-sampling period and the vertical drift level. We compare also the performances of the Lagrangian method to that of the classical Eulerian one. Finally we study the impact of errors on observations.Comment: 31 page