A 100 GHz coplanar strip circuit tuned with a sliding planar backshort

A means of mechanically altering the electrical length of a planar transmission line would greatly enhance the use of integrated circuit technology at millimeter and submillimeter wavelengths. Such a mechanically adjustable planar RF tuning element, successfully demonstrated at 100 GHz, is described here. It consists of a thin metallic sheet, with appropriately sized and spaced holes, which slides along on top of a dielectric-coated coplanar-strip transmission line. Multiple RF reflections caused by this structure add constructively, resulting in a movable RF short circuit, with |s11|≫APX=/-0.3 dB, which can be used to vary the electrical length of a planar tuning stub. The sliding short is used here to produce a 2-dB improvement in the response of a diode detector. This tuning element can be integrated with planar circuits to compensate for the effect of parasitic reactance inherent in various devices including semiconductor diodes and superconductor-insulator-superconductor (SIS) junctions

Noncontacting waveguide backshort

A noncontacting waveguide backshort is provided for use with frequencies of interest between 1 and 1000 GHz including a relatively rugged metallic bar movably mounted within the waveguide in a MYLAR insulator. A series of regularly shaped and spaced circular or rectangular openings are made in the metallic bar to form sections of high impedance alternating with sections of the bar having low impedance. This creates a periodic impedance variation which serves to provided an adjustable short circuit in a waveguide for the frequencies of interest

Should There Be a Presumption Favoring Awards of Attorney’s Fees in Copyright Litigation?, 12 J. Marshall Rev. Intell. Prop. L. 630 (2013)

Section 505 of the Copyright Act allows courts to award attorney’s fees to the prevailing party in a copyright case. Almost twenty years ago, the Supreme Court in Fogerty resolved a split among the circuits over the interpretation of that statute. First, it held that courts should apply several nonexclusive factors when determining if the prevailing party, whether defendant or plaintiff, should be entitled to recover attorney’s fees. Second, the Court refused to apply a presumption that the prevailing party will automatically recover attorney’s fees, opting instead for the districts courts to apply “equitable discretion” in awarding fees. But in recent years, the Seventh Circuit has called for “presumptive entitlement” of attorney\u27s fees to the prevailing party. It also isolated two factors as being primary in its analysis: the strength of the prevailing party\u27s case and the amount of damages the prevailing party obtained. Because the prevailing defendant typically receives no monetary award, the Seventh Circuit\u27s factors tend to favor the defendant. This paper points out the number of problems with such a presumption, including: 1) its conflicts with the statute; 2) conflicts with the principles of Fogerty; and 3) its chilling effect on plaintiffs with legitimate claims

Silicon micromachined waveguides for millimeter-wave and submillimeter-wave frequencies

The development of micromachining techniques to create silicon-based waveguide circuits, which can operate up to high submillimeter-wave frequencies, is reported. As a first step, a WR-10 waveguide has been fabricated from (110) silicon wafers. Insertion loss measurements on a gold-plated silicon waveguide show performance comparable to that of standard metal waveguides. It is suggested that active devices and planar circuits can be integrated with the waveguides, solving the traditional mounting problems

An adjustable RF tuning element for microwave, millimeter wave, and submillimeter wave integrated circuits

Planar RF circuits are used in a wide range of applications from 1 GHz to 300 GHz, including radar, communications, commercial RF test instruments, and remote sensing radiometers. These circuits, however, provide only fixed tuning elements. This lack of adjustability puts severe demands on circuit design procedures and materials parameters. We have developed a novel tuning element which can be incorporated into the design of a planar circuit in order to allow active, post-fabrication tuning by varying the electrical length of a coplanar strip transmission line. It consists of a series of thin plates which can slide in unison along the transmission line, and the size and spacing of the plates are designed to provide a large reflection of RF power over a useful frequency bandwidth. Tests of this structure at 1 GHz to 3 Ghz showed that it produced a reflection coefficient greater than 0.90 over a 20 percent bandwidth. A 2 GHz circuit incorporating this tuning element was also tested to demonstrate practical tuning ranges. This structure can be fabricated for frequencies as high as 1000 GHz using existing micromachining techniques. Many commercial applications can benefit from this micromechanical RF tuning element, as it will aid in extending microwave integrated circuit technology into the high millimeter wave and submillimeter wave bands by easing constraints on circuit technology