Proposed magneto-electrostatic ring trap for neutral atoms

We propose a novel trap for confining cold neutral atoms in a microscopic ring using a magneto-electrostatic potential. The trapping potential is derived from a combination of a repulsive magnetic field from a hard drive atom mirror and the attractive potential produced by a charged disk patterned on the hard drive surface. We calculate a trap frequency of [29.7, 42.6, 62.8] kHz and a depth of [16.1, 21.8, 21.8] MHz for [133Cs, 87Rb, 40K], and discuss a simple loading scheme and a method for fabrication. This device provides a one-dimensional potential in a ring geometry that may be of interest to the study of trapped quantum degenerate one-dimensional gases.Comment: 4 pages, 2 figures; revised, including new calculations and further discussio

Fabrication of Resorcinol-Formaldehyde Xerogel based High Aspect Ratio 3-D Hierarchical C-MEMS Structures

We demonstrate a novel method to fabricate arrays of resorcinol- formaldehyde xerogel (RFX) based high aspect ratio (HAR) three- dimensional (3-D) hierarchical C-MEMS structures. Starting from a master pattern of HAR 3-D posts fabricated in SU-8 negative photoresist by photolithography, a negative PDMS stamp with arrays of holes was prepared by micromolding. The PDMS stamp was then used to fabricate HAR 3-D RFX posts by replica molding. The 3-D RFX posts thus fabricated were electrosprayed with SU-8 or an RF sol in the form of submicron or nano sized droplets and followed by pyrolysis to yield HAR 3-D hierarchical carbon posts. To characterize their use in C-MEMS based batteries, galvanostatic (charge and discharge) experiments on RFX derived carbon showed that it can be reversibly intercalated with Li ions and possesses superior intercalation properties as compared to SU- 8 derived carbon which is a widely used material in C-MEMS

A comparative investigation of thickness measurements of ultra-thin water films by scanning probe techniques

The reliable operation of micro and nanomechanical devices necessitates a thorough knowledge of the water film thickness present on the surfaces of these devices with an accuracy in the nm range. In this work, the thickness of an ultra-thin water layer was measured by distance tunnelling spectroscopy and distance dynamic force spectroscopy during desorption in an ultra-high vacuum system, from about 2.5 nm up to complete desorption at 1E-8 mbar. The tunnelling current as well as the amplitude of vibration and the normal force were detected as a function of the probe-sample distance. In these experiments, a direct conversion of the results of both methods is possible. From the standpoint of surface science, taking the state-of-the-art concerning adsorbates on surfaces into consideration, dynamic force spectroscopy provides the most accurate values. The previously reported tunnelling spectroscopy, requiring the application of significantly high voltages, generally leads to values that are 25 times higher than values determined by dynamic force spectroscopy

Surface scattering velocities in III-nitride quantum well laser structures via the emission of hybrid phonons

We have theoretically and numerically studied nitride-based quantum well (QW) laser structures. More specifically, we have used a QW made with III-nitride where the width of the barrier region is large relative to the electron mean free path, and we have calculated the electron surface capture velocities by considering an electron flux which is captured into the well region. The process is assisted by the emission of the longitudinal optical phonons as predicted by the hybrid (HB) model. The results of surface capture velocities via the emission of HB phonons are compared to the emission of the dielectric continuum phonons (Zakhleniuk et al 1999 Phys. Status Solidi a 176 79). Our investigation shows that the two different phonon models predict almost the same results for the non-retarded limit. Furthermore, the surface capture velocities strongly depend on the size of the structure and the heterostructure materials. Lastly, a comparison to the recent experimental values shows that our model could accurately describe the experimentally measured parameters of the quantum capture processes

Decoupled cantilever arms for highly versatile and sensitive temperature and heat flux measurements

Microfabricated cantilever beams have been used in microelectromechanical systems for a variety of sensor and actuator applications. Bimorph cantilevers accurately measure temperature change and heat flux with resolutions several orders of magnitude higher than those of conventional sensors such as thermocouples, semiconductor diodes, as well as resistance and infrared thermometers. The use of traditional cantilevers, however, entails a series of important measurement limitations, because their interactions with the sample and surroundings often create parasitic deflection forces and the typical metal layer degrades the thermal sensitivity of the cantilever. The paper introduces a design to address these issues by decoupling the sample and detector section of the cantilever, along with a thermomechanical model, the fabrication, system integration, and characterization. The custom-designed bi-arm cantilever is over one order of magnitude more sensitive than current commercial cantilevers due to the significantly reduced thermal conductance of the cantilever sample arm. The rigid and immobile sample section offers measurement versatility ranging from photothermal absorption, near-field thermal radiation down to contact, conduction, and material thermal characterization measurements in nearly identical configurations.United States. Dept. of Energy. Division of Materials Sciences and Engineering (DE-FG02-02ER45977)United States. Air Force Office of Scientific Research. Multidisciplinary University Research Initiative (UIUC FA9550-08-1-0407

Vacuum/Compression Valving (VCV) Using Parrafin-Wax on a Centrifugal Microfluidic CD Platform

This paper introduces novel vacuum/compression valves (VCVs) utilizing paraffin wax. A VCV is implemented by sealing the venting channel/hole with wax plugs (for normally-closed valve), or to be sealed by wax (for normally-open valve), and is activated by localized heating on the CD surface. We demonstrate that the VCV provides the advantages of avoiding unnecessary heating of the sample/reagents in the diagnostic process, allowing for vacuum sealing of the CD, and clear separation of the paraffin wax from the sample/reagents in the microfluidic process. As a proof of concept, the microfluidic processes of liquid flow switching and liquid metering is demonstrated with the VCV. Results show that the VCV lowers the required spinning frequency to perform the microfluidic processes with high accuracy and ease of control.open5

Fabrication and electrical integration of robust carbon nanotube micropillars by self-directed elastocapillary densification

Vertically-aligned carbon nanotube (CNT) "forest" microstructures fabricated by chemical vapor deposition (CVD) using patterned catalyst films typically have a low CNT density per unit area. As a result, CNT forests have poor bulk properties and are too fragile for integration with microfabrication processing. We introduce a new self-directed capillary densification method where a liquid is controllably condensed onto and evaporated from CNT forests. Compared to prior approaches, where the substrate with CNTs is immersed in a liquid, our condensation approach gives significantly more uniform structures and enables precise control of the CNT packing density and pillar cross-sectional shape. We present a set of design rules and parametric studies of CNT micropillar densification by this method, and show that self-directed capillary densification enhances the Young's modulus and electrical conductivity of CNT micropillars by more than three orders of magnitude. Owing to the outstanding properties of CNTs, this scalable process will be useful for the integration of CNTs as functional material in microfabricated devices for mechanical, electrical, thermal, and biomedical applications

Micro-fabrication of Carbon Structures by Pattern Miniaturization in Resorcinol-Formaldehyde Gel

A simple and novel method to fabricate and miniaturize surface and sub-surface micro-structures and micro-patterns in glassy carbon is proposed and demonstrated. An aqueous resorcinol-formaldehyde (RF) sol is employed for micro-molding of the master-pattern to be replicated, followed by controlled drying and pyrolysis of the gel to reproduce an isotropically shrunk replica in carbon. The miniaturized version of the master-pattern thus replicated in carbon is about one order of magnitude smaller than original master by repeating three times the above cycle of molding and drying. The micro-fabrication method proposed will greatly enhance the toolbox for a facile fabrication of a variety of Carbon-MEMS and C-microfluidic devices.Comment: 16 pages, 5 figure

Opportunities for mesoscopics in thermometry and refrigeration: Physics and applications

This review presents an overview of the thermal properties of mesoscopic structures. The discussion is based on the concept of electron energy distribution, and, in particular, on controlling and probing it. The temperature of an electron gas is determined by this distribution: refrigeration is equivalent to narrowing it, and thermometry is probing its convolution with a function characterizing the measuring device. Temperature exists, strictly speaking, only in quasiequilibrium in which the distribution follows the Fermi-Dirac form. Interesting nonequilibrium deviations can occur due to slow relaxation rates of the electrons, e.g., among themselves or with lattice phonons. Observation and applications of nonequilibrium phenomena are also discussed. The focus in this paper is at low temperatures, primarily below 4 K, where physical phenomena on mesoscopic scales and hybrid combinations of various types of materials, e.g., superconductors, normal metals, insulators, and doped semiconductors, open up a rich variety of device concepts. This review starts with an introduction to theoretical concepts and experimental results on thermal properties of mesoscopic structures. Then thermometry and refrigeration are examined with an emphasis on experiments. An immediate application of solid-state refrigeration and thermometry is in ultrasensitive radiation detection, which is discussed in depth. This review concludes with a summary of pertinent fabrication methods of presented devices.Comment: Close to the version published in RMP; 59 pages, 35 figure