4,735 research outputs found
On Safe Folding
In [3] a general fold operation has been introduced for definite programs wrt computed answer substitution semantics. It differs from the fold operation defined by Tamaki and Sato in [26,25] because its application does not depend on the transformation history. This paper extends the results in [3] by giving a more powerful sufficient condition for the preservation of computed answer substitutions. Such a condition is meant to deal with the critical case when the atom introduced by folding depends on the clause to which the fold applies. The condition compares the dependency degree between the fonding atom and the folded clause, with the semantic delay between the folding atom and the ones to be folded. The result is also extended to a more general replacement operation, by showing that it can be decomposed into a sequence of definition, general folding and unfolding operations
Crew emergency return vehicle autoland feasibility study
The crew emergency return vehicle (CERV) autoland feasibility study focused on determining the controllability of the NASA Langley high lift over drag CERV for performing an automatic landing at a prescribed runway. An autoland system was developed using integral linear quadratic Gaussian (LQG) design techniques. The design was verified using a nonlinear 6 DOF simulation. Simulation results demonstrate that the CERV configuration is a very flyable configuration for performing an autoland mission. Adequate stability and control was demonstrated for wind turbulence and wind shear. Control surface actuator requirements were developed
Personnel launch system autoland development study
The Personnel Launch System (PLS) Autoland Development Study focused on development of the guidance and control system for the approach and landing (A/L) phase and the terminal area energy management (TAEM) phase. In the A/L phase, a straight-in trajectory profile was developed with an initial high glide slope, a pull-up and flare to lower glide slope, and the final flare touchdown. The TAEM system consisted of using a heading alignment cone spiral profile. The PLS autopilot was developed using integral LQG design techniques. The guidance and control design was verified using a nonlinear 6 DOF simulation. Simulation results demonstrated accurate steering during the TAEM phase and adequate autoland performance in the presence of wind turbulence and wind shear
A new data assimilation procedure to develop a debris flow run-out model
Abstract Parameter calibration is one of the most problematic phases of numerical modeling since the choice of parameters affects the model\u2019s reliability as far as the physical problems being studied are concerned. In some cases, laboratory tests or physical models evaluating model parameters cannot be completed and other strategies must be adopted; numerical models reproducing debris flow propagation are one of these. Since scale problems affect the reproduction of real debris flows in the laboratory or specific tests used to determine rheological parameters, calibration is usually carried out by comparing in a subjective way only a few parameters, such as the heights of soil deposits calculated for some sections of the debris flows or the distance traveled by the debris flows using the values detected in situ after an event has occurred. Since no automatic or objective procedure has as yet been produced, this paper presents a numerical procedure based on the application of a statistical algorithm, which makes it possible to define, without ambiguities, the best parameter set. The procedure has been applied to a study case for which digital elevation models of both before and after an important event exist, implicating that a good database for applying the method was available. Its application has uncovered insights to better understand debris flows and related phenomena
Energy conversion systems: the case study of compressed air, an introduction to a new simulation toolbox
The paper illustrates the simulation activities going on within
the LABAC (laboratory of energy performance of compressed
air systems) at the University of Pavia. The scope is to build
up a simulator, based on a comprehensive energy model, en-
abling the end-user both to improve the system efficiency, al-
lowing modifications on the system configuration and/or the
use of alternative devices, and to properly size a pneumatic
network. The final use is both for educational and test pur-
pose. The simulator represents the laboratory plant, where the
generation unit, the receiver, the cleaning up equipment and
the distribution of compressed air are set in place. For the
modeling, the Xcos application, graphical Scilab interface,
has been used; to emphasize the potential derived by the use
of this simulator, the role of increasing storage unit/receiver
is investigated with respect to the system energy consump-
tion. Several testings have been performed. The simulation
reported in this paper has been carried out for 4000 s and two
different configurations are investigated: the living one with
0.5 m3 vs. the alternative 6.5 m3 storage tank. A detailed ap-
proach to the identification of all equipment is proposed and
energy and power considerations are reported
Acceptability with general orderings
We present a new approach to termination analysis of logic programs. The
essence of the approach is that we make use of general orderings (instead of
level mappings), like it is done in transformational approaches to logic
program termination analysis, but we apply these orderings directly to the
logic program and not to the term-rewrite system obtained through some
transformation. We define some variants of acceptability, based on general
orderings, and show how they are equivalent to LD-termination. We develop a
demand driven, constraint-based approach to verify these
acceptability-variants.
The advantage of the approach over standard acceptability is that in some
cases, where complex level mappings are needed, fairly simple orderings may be
easily generated. The advantage over transformational approaches is that it
avoids the transformation step all together.
{\bf Keywords:} termination analysis, acceptability, orderings.Comment: To appear in "Computational Logic: From Logic Programming into the
Future
The -semantics approach; theory and applications
AbstractThis paper is a general overview of an approach to the semantics of logic programs whose aim is to find notions of models which really capture the operational semantics, and are, therefore, useful for defining program equivalences and for semantics-based program analysis. The approach leads to the introduction of extended interpretations which are more expressive than Herbrand interpretations. The semantics in terms of extended interpretations can be obtained as a result of both an operational (top-down) and a fixpoint (bottom-up) construction. It can also be characterized from the model-theoretic viewpoint, by defining a set of extended models which contains standard Herbrand models. We discuss the original construction modeling computed answer substitutions, its compositional version, and various semantics modeling more concrete observables. We then show how the approach can be applied to several extensions of positive logic programs. We finally consider some applications, mainly in the area of semantics-based program transformation and analysis
- …