Rotary ultrasonic bone drilling: improved pullout strength and reduced damage

Bone drilling is one of the most common operations used to repair fractured parts of bones. During a bone drilling process, microcracks are generated on the inner surface of the drilled holes that can detrimentally affect osteosynthesis and healing. This study focuses on the investigation of microcracks and pullout strength of cortical-bone screws in drilled holes. It compares conventional surgical bone drilling (CSBD) with rotary ultrasonic bone drilling (RUBD), a novel approach employing ultrasonic vibration with a diamond-coated hollow tool. Both techniques were used to drill holes in porcine bones in an in-vitro study.Scanning electron microscopy was used to observe microcracks and surface morphology. The results obtained showed a significant decrease in the number and dimensions of microcracks generated on the inner surface of drilled holes with the RUBD process in comparison to CSBD. It was also observed that a higher rotational speed and a lower feed rate resulted in lower damage, i.e. fewer microcracks. Biomechanical axial pullout strength of a cortical bone screw inserted into a hole drilled with RUBD was found to be much higher (55–385%) than that for CSBD

Environmental Resource - Economized Processes of Recycling Mineral Raw Materials of Complex Composition

The results of the studies on the justification of technological processes providing recycling of the warehoused ferruginous quartzites of complex composition and waste non-ferrous metals allowing to receive additional commodity products are given. The example of amphibole and biotite varieties of ferruginous quartzites of CMA and tailings of copper-zinc sulphide Ural ores determines the reasons of ineffective use of traditional technology solutions for recycling. The reasons of environmental hazards concerning varieties of technogenic mineral substances to the environment are identified. The presence in ferruginous quartzites complex composition of various silicates, carbonates and iron sulphides change their technological properties. So to get the iron concentrate from them suggests a new combination of technological operations performed in specially selected operating conditions. The specifics of the presence of mineral components in solid mineral wastes of nonferrous metal ores indicates the possibility of obtaining additional marketable products. With the use of laboratory multiscale modelling and physical methods of analysis regularities of variation of fractionation, separation and mineral concentration operations efficiency by varying its composition and the various influencing factors are identified. To improve the efficiency of the individual technological operations it is recommended to use different techniques, using physical and physico-chemical effects on the polymineral systems. The flow diagrams for the considered varieties of technogenic processing of mineral substances, allowing them to obtain standared quality products (metal-containing concentrates), and the results of their testing are submitted. The suggested technological solutions can reduce the amount of environmentally hazardous mineral substance, hosted in technogenic formations

Multi-objective optimization of ultrasonic-assisted magnetic abrasive finishing process

Ultrasonic-assisted magnetic abrasive finishing (UAMAF) is an advanced abrasive finishing process that finishes a workpiece surface effectually when compared to a traditional magnetic abrasive finishing process in the order of nanometer. A change of surface roughness and material removal rate are two important factors determining the efficacy of the process. These two factors affect the surface quality and production time and, thereby, a total production cost. The finishing performed at higher material removal rates leads to a loss in shape/form accuracy of the surface. At the same time, increasing the rate of change of surface roughness increases loss of material. For an optimized finishing process, a compromise has to be made between the change of surface roughness and the material removal (loss). In this work, a multi-objective optimization technique based on genetic algorithm is used to optimize the finishing parameters in the UAMAF processes. A fuzzy-set-based strategy for a higher level decision is also discussed. The results of the optimization based on a mathematical model of the process are validated with the experimental results and are found to be in compliance

Modeling of finishing force and torque in ultrasonic-assisted magnetic abrasive finishing process

A new finishing technique called ultrasonic-assisted magnetic abrasive finishing integrates ultrasonic vibration with magnetic abrasive finishing process for finishing of workpiece surface more efficiently as compared to magnetic abrasive finishing in the nanometer range. During finishing, two types of forces are generated in ultrasonic-assisted magnetic abrasive finishing, namely, a normal force (indentation force) and a tangential force (cutting force) that produces a torque. The finishing forces have direct control on the rate of change of surface roughness and material removal rate of the workpiece surface. This article deals with the theoretical modeling of the normal force and the finishing torque based on the process physics. In this work, finite element simulations of the electromagnet were performed to calculate a magnetic flux density in the working zone; they were also used to evaluate the normal force on the workpiece surface. The theory of friction for the abrasion of metals was applied together with the effect of ultrasonic vibration to calculate the finishing torque. The developed model predicts the normal force and finishing torque in ultrasonic-assisted magnetic abrasive finishing as functions of the supply voltage, working gap and concentration of abrasive particles in a flexible magnetic abrasive brush. A comparison of theoretical and experimental results is performed to validate the proposed model

Vibration characteristics of MR cantilever sandwich beams: experimental study

The concept of vibration controllability with smart fluids within flexible structures has been in the centre of interest in the past two decades. Although much research has been done on structures with embedded electrorheological (ER) fluids, there has been little investigation of magnetorheological (MR) fluid adaptive structures. In particular, a body of research on experimental work of cantilever MR beams is still lacking. This experimental study investigates controllability of vibration characteristics of magnetorheological cantilever sandwich beams. These adaptive structures are produced by embedding an MR fluid core between two elastic layers. The structural behaviour of the MR beams can be varied by applying an external magnetic field to activate the MR fluid. The stiffness and damping structural characteristics are controlled, demonstrating vibration suppression capabilities of MR fluids as structural elements. MR beams were fabricated with two different materials for comparison purposes. Diverse excitation methods were considered as well as a range of magnetic field intensities and configurations. Moreover, the cantilever MR beams were tested in horizontal and vertical configurations. The effects of partial and full activation of the MR beams were outlined based on the results obtained. Controllability of the beam’s vibration response was observed in the form of variations in vibration amplitudes and shifts in magnitudes of the resonant natural frequency

Modeling of normal force and finishing torque considering shearing and ploughing effects in ultrasonic assisted magnetic abrasive finishing process with sintered magnetic abrasive powder

Ultrasonic assisted magnetic abrasive finishing process (UAMAF) is a precision manufacturing process that results nano-scale level finish in a part. Normal force on a particle helps indenting the particle in the work surface whereas horizontal force provides finishing torque that in-turn helps the particle to perform micro-machining. Better understanding of the effect of these forces on material removal and wear pattern of the work-piece necessitates mathematical modeling of normal force and finishing torque and subsequently its validation with experimental results. In the present study, single particle interaction concept is considered to develop a model which is subsequently applied for all active particles of magnetic abrasive powder (MAP). Separation point theory is applied to consider the effect of ploughing below a critical depth and shearing above that depth. Normal components of shearing and ploughing forces are considered for calculating normal force and horizontal components of shearing and ploughing forces are taken to calculate finishing torque. Johnson-Cook model is applied to calculate shearing strength of the work material during UAMAF. The impact of ultrasonic vibrations is considered while calculating strain rate. Images are taken with the help of scanned electron microscope and atomic force microscope to study the material removal and wear mechanism during UAMAF process. Predicted values of force and torque model are validated with the experimental values

A micromechanism study of thermosonic gold wire bonding on aluminum pad

A micromechanism of thermosonic gold wire bonding was elaborated by examining its interfacial characteristics as a result of the bonding process, including the fragmentation of the native aluminum oxide layer on Al pads, and formation of initial intermetallic compounds IMCs. It is found that the existence of an approximately 5 nm thick native oxide layer on original Al pads has a significant effect on the bonding, and the nucleation of IMCs during the bonding process must overcome this relatively inert thin film. Bonding strength was fundamentally determined by the degree of fragmentation of the oxide films, through which the formation of IMCs can be initiated due to the direct contact of the metal surfaces to be bonded. The extent of fracture the oxide layer was strongly influenced by the level of ultrasonic power, as at its high level alumina fragmentation becomes pervasive resulting in contiguous alloy interfaces and robust bonds. The IMCs formed at the interfaces were identified as Al₄Al and AuAl₂ with a thickness of 150–300 nm. The formation mechanism of such IMCs was explained by the effective heat of formation theory.This research was funded as a PMI2 Project Grant No. RC 41 through the UK Department for Innovation, Universities and Skills DIUS

A micromechanism study of thermosonic gold wire bonding on aluminum pad

A micromechanism of thermosonic gold wire bonding was elaborated by examining its interfacial characteristics as a result of the bonding process, including the fragmentation of the native aluminum oxide layer on Al pads, and formation of initial intermetallic compounds IMCs. It is found that the existence of an approximately 5 nm thick native oxide layer on original Al pads has a significant effect on the bonding, and the nucleation of IMCs during the bonding process must overcome this relatively inert thin film. Bonding strength was fundamentally determined by the degree of fragmentation of the oxide films, through which the formation of IMCs can be initiated due to the direct contact of the metal surfaces to be bonded. The extent of fracture the oxide layer was strongly influenced by the level of ultrasonic power, as at its high level alumina fragmentation becomes pervasive resulting in contiguous alloy interfaces and robust bonds. The IMCs formed at the interfaces were identified as Al₄Al and AuAl₂ with a thickness of 150–300 nm. The formation mechanism of such IMCs was explained by the effective heat of formation theory.This research was funded as a PMI2 Project Grant No. RC 41 through the UK Department for Innovation, Universities and Skills DIUS

Evaluation of the chemical and biomechanical viscoelastic properties of decellularised tracheal scaffolds [46]

Evaluation of the chemical and biomechanical viscoelastic properties of decellularised tracheal scaffolds [46