Spatial deconvolution of IRAS galaxies at 60 UM

Using IRAS in a slow scan observing mode to increase the spatial sampling rate and a deconvolution analysis to increase the spatial resolution, several bright galaxies were resolved at 60 micron. Preliminary results for M 82, NGC 1068, NGC 3079 and NGC 2623 show partially resolved emission from 10 to 26 arcsec., full width at half maximum, and extended emission from 30 to 90 arcsec. from the center. In addition, the interacting system, Arp 82, along with Mark 231 and Arp 220 were studied using the program ADDSCAN to average all available survey mode observations. The Arp 82 system is well resolved after deconvolution and its brighter component is extended; the two most luminous objects are not resolved with an upper limit of 15 arcsec. for Arp 220

Flying infrared telescope Final report, 1 Apr. 1967 - 31 May 1971

Airborne infrared telescope for flux measurements of astronomical objects with spectral energy peaks occurring at wavelengths of more than 25 micron

Continued development and application of far-infrared detection techniques

The development of a balloon gondola and pointing system are discussed which can be used with the low background far infrared telescope. Flight test progress of the new gondola is reported using a 3-axis system which would provide much greater capabilities. In this design both a polar and declination axis are use and are maintained in the proper orientation by a free handing (vertical) azimuth shaft

The Red Queen visits Minkowski Space

When Alice went `Through the Looking Glass' [1], she found herself in a situation where she had to run as fast as she could in order to stay still. In accordance with the dictum that truth is stranger than fiction, we will see that it is possible to find a situation in special relativity where running towards one's target is actually counter-productive. Although the situation is easily analysed algebraically, the qualitative properties of the analysis are greatly illuminated by the use of space-time diagrams

A joint program with Japanese investigators to map carbon 2 line emission from the galaxy

A large portion of the inner galactic plane has been mapped in the far-infrared (C II) line using a balloon-borne survey instrument. Complete coverage is reported from 25 degrees north to 80 degrees south of the galactic center and extending a few degrees on each side of the plane. Effective resolution is 14.1 acrmin (FWHM) and contour levels begin at 2 E -5 ergs/(s x sq. cm x ster). When compared with 100 micron dust emission observed by IRAS the (C II) appears well correlated with the dust emission except for a 10 degree region centered on the galactic center where emission from the gas is much weaker than that from the dust

The effect of microstructure and strength on the fracture toughness of an 18 Ni, 300 grade maraging steel

Fractography and metallographic sectioning were used to investigate the influence of microstructure and strength on the fracture toughness (KIc) and fracture mechanism of an 18 Ni, 300 grade maraging steel. Increased yield strength from 1442 to 2070 MN/m squared through precipitation hardening results in a KIc loss from 143 to 55 MN/m superscript 3/2. Ti (C,N) Ti2S, and TiC inclusions in sizes from 1 to 8, 1 to 15, and 0.1 to 2 microns respectively serve as sites for void nucleation and lead to fracture by the dimpled rupture process in all strength levels considered. TiC nucleated dimples occupy more than half the fracture in all conditions. Void nucleation rate and resultant number of dimples per unit area of fracture increase with increasing yield strength. Average dimple size decreases with increasing strength and/or overaging which follows from the decreasing amount of stable void growth measured by sectioning tensile specimens. Void growth is assisted by crack branching along a path of TiC inclusions. Coalescence occurs in the highest strength materials by a combination of TiC void nucleation and premature separation at strengthening precipitates

The effect of microstructure and strength on the fracture toughness of an 18 Ni, 300 grade maraging steel

A 300 grade maraging steel was chosen as a vehicle by which to understand the inverse relationship between strength and toughness in high strength alloys such as the 18 Ni maraging steels. The 18 Ni, 300 grade maraging material was a commercial grade consumable-electrode, vacuum arc remelted heat obtained in the form of forged and annealed plate. The matrix contained a population of second-phase impurity inclusions which was a product of the casting and hot working processes. These inclusions did not change with subsequent precipitation hardening. Changes in microstructure resulting in strength increases were brought about by variations in aging temperature and time. Maximum strength was attained in the 300 grade maraging steel by aging at 427 C (800 F) for 100 hours. Tensile, fatigue precracked Charpy impact, and plane-strain fracture toughness tests were performed at room temperature, 20 C (68 F). With increasing strength the fracture toughness decreases as smaller and smaller inclusions act as sites for void initiation

Glyoxal 4-nitrophenylhydrazone : triple helices linked into a three-dimensional channel structure

Peer reviewedPublisher PD

Study of photoconductive indium antimonide

Indium antimonide (InSb) material was assessed for use as photoconductive infrared detectors under low background conditions. Such detectors must be more rugged, and have lower capacitance, than the common photovoltaic InSb detector. Electronic grade n-type InSb was etched to 50 micrometers thickness, and tin and gold contacts were applied by evaporation. The test devices showed a relatively low ultimate impedance: 7 Mohms at 4.2 K. This was attributed to the presence of impurity levels of very shallow energies, and this material was judged unsuitable for low background detection