232,104 research outputs found
Reduction of porosity in aluminum weldments
Method is described for elimination of porosity of aluminum weldments by replacing polyvinyl chloride tubing (used to connect welder to gas source, and is permeable to moisture at high humidity) with copper tubing. In addition liquid argon gas is used at weld stations
Time evolution of rolling tachyons for a brane-antibrane pair
A precise form of the time evolution of rolling tachyons corresponding to a
brane-antibrane pair is investigated by solving the Hamiltonian equations of
motion under the assumption that in a region far away from branes the tachyon
vacuum is almost already achieved, even at the beginning of the rolling.Comment: 10 pages, 2 figures. Addition of references in v2, inclusion of more
details in v
c-axis Raman Scattering in MgB2: Observation of a Dirty-Limit Gap in the pi-bands
Raman scattering spectra from the ac-face of thick MgB2 single crystals were
measured in zz, xz and xx polarisations. In zz and xz polarisations a threshold
at around 29 cm^{-1} forms in the below Tc continuum but no pair-breaking peak
is seen, in contrast to the sharp pair-breaking peak at around 100 cm^{-1} seen
in xx polarisation. The zz and xz spectra are consistent with Raman scattering
from a dirty superconductor while the sharp peak in the xx spectra argues for a
clean system. Analysis of the spectra resolves this contradiction, placing the
larger and smaller gap magnitudes in the sigma and pi bands, and indicating
that relatively strong impurity scattering is restricted to the pi bands.Comment: Revised manuscript accepted for publication in Physical Review
Letter
Method for reinforcing tubing joints
Joint repair technique uses a longitudinally split aluminum shield over the joint ferrule and immediately adjacent tubing to reseal or reinforce leaking or weak joints in small tubing. Epoxy resin coating on inside surfaces of the two shield halves provides a tightly sealed bond between shield and tubing
Normal modes in an overmoded circular waveguide coated with lossy material
The normal modes in an overmoded waveguide coated with a lossy material are analyzed, particularly for their attenuation properties as a function of coating material, layer thickness, and frequency. When the coating material is not too lossy, the low-order modes are highly attenuated even with a thin layer of coating. This coated guide serves as a mode suppressor of the low-order modes, which can be particularly useful for reducing the radar cross section (RCS) of a cavity structure such as a jet inlet. When the coating material is very lossy, low-order modes fall into two distinct groups: highly and lowly attenuated modes. However, as a/lambda (a = radius of the cylinder; lambda = the free-space wavelength) increases, the separation between these two groups becomes less distinctive. The attenuation constants of most of the low-order modes become small, and decrease as a function of lambda sup 2/a sup 3
Regioselective Intermolecular Coupling Reaction of Arylketones and Alkenes Involving C-H Bond Activation Catalyzed by an \u3cem\u3ein Situ\u3c/em\u3e Formed Cationic Ruthenium-Hydride Complex
The cationic ruthenium hydride complex, formed in situ from the treatment of the tetranuclear ruthenium hydride complex {[(PCy3)(CO)RuH]4(μ4-O)(μ3-OH)(μ2-OH)} with HBF4·OEt2, was found to be a highly effective catalyst for the intermolecular coupling reaction of arylketones and 1-alkenes to give the substituted indene and ortho-C−H insertion products. The formation of the indene products resulted from the initial alkene isomerization followed by regioselective ortho-C−H insertion of 2-alkene and dehydrative cyclization. The preliminary mechanistic studies revealed a rapid and reversible ortho-C−H bond activation followed by the rate-limiting C−C bond formation step for the coupling reaction
Efficient Dehydrogenation of Amines and Carbonyl Compounds Catalyzed by a Tetranuclear Ruthenium-μ-oxo-μ-hydroxo-hydride Complex
The tetranuclear ruthenium-μ-oxo-μ-hydroxo-hydride complex {[(PCy3)(CO)RuH]4(μ4-O)(μ3-OH)(μ2-OH)} (1) was found to be a highly effective catalyst for the transfer dehydrogenation of amines and carbonyl compounds. For example, the initial turnover rate of the dehydrogenation of 2-methylindoline was measured to be 1.9 s−1 with a TON of 7950 after 1 h at 200 °C. The extensive H/D scrambling patterns observed from the dehydrogenation reaction of indoline-N-d1 and indoline-α-d2 suggest a monohydride mechanistic pathway with the C−H bond activation rate-limiting step
- …