20,870 research outputs found
A study of dynamic energy equations for Stirling cycle analysis
An analytical and computer study of the dynamic energy equations that describe the physical phenomena that occurs in a Stirling cycle engine. The basic problem is set up in terms of a set o hyperbolic partial differential equations. The characteristic lines are determined. The equations are then transformed to ordinary differential equations that are valid along characteristic lines. Computer programs to solve the differential equations and to plot pertinent factors are described
Monte Carlo simulation by computer for life-cycle costing
Prediction of behavior and support requirements during the entire life cycle of a system enables accurate cost estimates by using the Monte Carlo simulation by computer. The system reduces the ultimate cost to the procuring agency because it takes into consideration the costs of initial procurement, operation, and maintenance
Device for measuring the temperature of liquid and gaseous hydrogen Final report
Fabrication and test data cryogenic temperature transducer extremely fast in response to temperature changes - device for measuring temperature of liquid and gaseous hydroge
Impurity in a bosonic Josephson junction: swallowtail loops, chaos, self-trapping and the poor man's Dicke model
We study a model describing identical bosonic atoms trapped in a
double-well potential together with a single impurity atom, comparing and
contrasting it throughout with the Dicke model. As the boson-impurity coupling
strength is varied, there is a symmetry-breaking pitchfork bifurcation which is
analogous to the quantum phase transition occurring in the Dicke model. Through
stability analysis around the bifurcation point, we show that the critical
value of the coupling strength has the same dependence on the parameters as the
critical coupling value in the Dicke model. We also show that, like the Dicke
model, the mean-field dynamics go from being regular to chaotic above the
bifurcation and macroscopic excitations of the bosons are observed. Overall,
the boson-impurity system behaves like a poor man's version of the Dicke model.Comment: 17 pages, 16 figure
Program to design, fabricate, test, and deliver a thermal control-mixing control device for the George C. Marshall Space Flight Center
The development and testing of a temperature sensor and pulse duration modulation (PDM) diverter valve for a thermal control-mixing control device are described. The temperature sensor selected for use uses a fluidic pin amplifier in conjunction with an expansion device. This device can sense changes of less than 0.25 F with greater than 15:1 signal to noise ratio when operating with a typical Freon pump supplied pressure. The pressure sensitivity of the sensor is approximately 0.0019 F/kPa. The valve which was selected was tested and performed with 100% flow diversion. In addition, the valve operates with a flow efficiency of at least 95%, with the possibility of attaining 100% if the vent flow of the PDM can be channeled through the last stage of the diverter valve. A temperature sensor which utilized an orifice bridge circuit and proportional-vortex combination mixing valve were also evaluated, but the concepts were rejected due to various problems
Research into the feasibility of metal- and oxide-film capacitors
Thin film capacitors with up to twenty-two active layers have been deposited by RF sputtering. The materials were aluminum electrodes of 1200 to 1500 angstrom thickness and silica dielectric layers of 3000 to 6000 angstrom thickness. The best electrical characteristics were capacitances of nearly 0.1 microfarad for an active area of 1.25 square centimeters, dissipation factor of less than 0.01 over a frequency range of 0.5 to 100 kilohertz and energy density of approximately 70 millijoules per cubic centimeter of active deposited material at a working voltage of 40 volts. These aluminum-silica capacitors exhibit excellent electrical stability over a temperature range from -55 C to +300 C
Validity of adiabaticity in Cavity QED
This paper deals with the concept of adiabaticity for fully quantum
mechanically cavity QED models. The physically interesting cases of Gaussian
and standing wave shapes of the cavity mode are considered. An analytical
approximate measure for adiabaticity is given and compared with numerical wave
packet simulations. Good agreement is obtained where the approximations are
expected to be valid. Usually for cavity QED systems, the large atom-field
detuning case is considered as the adiabatic limit. We, however, show that
adiabaticity is also valid, for the Gaussian mode shape, in the opposite limit.
Effective semiclassical time dependent models, which do not take into account
the shape of the wave packet, are derived. Corrections to such an effective
theory, which are purely quantum mechanical, are discussed. It is shown that
many of the results presented can be applied to time dependent two-level
systems.Comment: 10 pages, 9 figure
Dicke-type phase transition in a multimode optomechanical system
We consider the "membrane in the middle" optomechanical model consisting of a
laser pumped cavity which is divided in two by a flexible membrane that is
partially transmissive to light and subject to radiation pressure. Steady state
solutions at the mean-field level reveal that there is a critical strength of
the light-membrane coupling above which there is a symmetry breaking
bifurcation where the membrane spontaneously acquires a displacement either to
the left or the right. This bifurcation bears many of the signatures of a
second order phase transition and we compare and contrast it with that found in
the Dicke model. In particular, by studying limiting cases and deriving
dynamical critical exponents using the fidelity susceptibility method, we argue
that the two models share very similar critical behaviour. For example, the
obtained critical exponents indicate that they fall within the same
universality class. Away from the critical regime we identify, however, some
discrepancies between the two models. Our results are discussed in terms of
experimentally relevant parameters and we evaluate the prospects for realizing
Dicke-type physics in these systems.Comment: 14 pages, 6 figure
CO2 laser waveguiding in proton implanted GaAs
Surface layers capable of supporting optical modes at 10.6 microns have been produced in n-type GaAs wafers through 300 keV proton implantation. The dominant mechanism for this effect appears to be free carrier compensation. Characterization of the implanted layers by analysis of infrared reflectivity spectra and synchronous coupling at 10.6 microns produced results in good agreement with elementary models. These results of sample characterization by infrared reflectivity and by CO2 laser waveguiding as implanted are presented and evaluated
- …