17,424 research outputs found
Communicating with organic producers in Wales
This paper reviews the services and activities through which the research and development community communicates with producers in Wales. These include publications (in hard copy and electronic media), one to one advisory services and group activities. It examines the appropriateness of different approaches for different situations, and makes the case for better integration of services under the new rural development plan
Dynamic FOV visible light communications receiver for dense optical networks
This study explores how the field-of-view (FOV) of a visible light communications (VLCs) receiver can be manipulated to realise the best signal-to-noise ratio (SNR) while supporting device mobility and optimal access point (AP) selection. The authors propose a dynamic FOV receiver that changes its aperture according to receiver velocity, location, and device orientation. The D-FOV technique is evaluated through modelling, analysis, and experimentation in an indoor environment comprised of 15 VLC APs. The proposed approach is also realised as an algorithm that is studied through analysis and simulation. The results of the study indicate the efficacy of the approach including a 3X increase in predicted SNR over static FOV approaches based on measured received signal strength in the testbed. Additionally, the collected data reveal that D-FOV increases effectiveness in the presence of noise. Finally, the study describes the tradeoffs among the number of VLC sources, FOV, user device velocity, and SNR as a performance metric.Accepted manuscrip
Further detections of OH masers in carbon stars with silicate features
A sample of J-type carbon stars was searched for OH maser emission. The new
detection of three OH lines towards two silicate carbon stars is reported. In
V778 Cyg, previously known as the main-lines (1665 and 1667 MHz) maser source,
the satellite 1612 MHz emission was discovered while in NSV 2814 the main OH
lines were detected. The presence of OH maser lines confirms the former
suggestion that oxygen-rich material is located in the vicinity (
cm) of silicate carbon stars.Comment: LaTeX2e, 4 pages with 2 figure
Single-stage, low-noise, advanced technology fan. Volume 4: Fan aerodynamics. Section 1: Results and analysis
Test results at design speed show fan total pressure ratio, weight flow, and adiabatic efficiency to be 2.2, 2.9, and 1.8% lower than design goal values. The hybrid acoustic inlet (which utilizes a high throat Mach number and acoustic wall treatment for noise suppression) demonstrated total pressure recoveries of 98.9% and 98.2% at takeoff and approach. Exhaust duct pressure losses differed between the hardwall duct and treated duct with splitter by about 0.6% to 2.0% in terms of fan exit average total pressure (depending on operating condition). When the measured results were used to estimate pressure losses, a cruise sfc penalty of 0.68%, due to the acoustically treated duct, was projected
Response of a small-turboshaft-engine compression system to inlet temperature distortion
An experimental investigation was conducted into the response of a small-turboshaft-engine compression system to steady-state and transient inlet temperature distortions. Transient temperature ramps range from less than 100 K/sec to above 610 K/sec and generated instantaneous temperatures to 420 K above ambient. Steady-state temperature distortion levels were limited by the engine hardware temperature list. Simple analysis of the steady-state distortion data indicated that a particle separator at the engine inlet permitted higher levels of temperature distortion before onset of compressor surge than would be expected without the separator
Single stage, low noise, advanced technology fan. Volume 1: Aerodynamic design
The aerodynamic design for a half-scale fan vehicle, which would have application on an advanced transport aircraft, is described. The single stage advanced technology fan was designed to a pressure ratio of 1.8 at a tip speed of 503 m/sec 11,650 ft/sec). The fan and booster components are designed in a scale model flow size convenient for testing with existing facility and vehicle hardware. The design corrected flow per unit annulus area at the fan face is 215 kg/sec sq m (44.0 lb m/sec sq ft) with a hub-tip ratio of 0.38 at the leading edge of the fan rotor. This results in an inlet corrected airflow of 117.9 kg/sec (259.9 lb m/sec) for the selected rotor tip diameter if 90.37 cm (35.58 in.). The variable geometry inlet is designed utilizing a combination of high throat Mach number and acoustic treatment in the inlet diffuser for noise suppression (hybrid inlet). A variable fan exhaust nozzle was assumed in conjunction with the variable inlet throat area to limit the required area change of the inlet throat at approach and hence limit the overall diffusion and inlet length. The fan exit duct design was primarily influenced by acoustic requirements, including length of suppressor wall treatment; length, thickness and position on a duct splitter for additional suppressor treatment; and duct surface Mach numbers
- …