159 research outputs found

    Sequential biological and photocatalysis based treatments for shipboard slop purification: A pilot plant investigation

    Get PDF
    This study investigated the treatment of a shipboard slop containing commercial gasoline in a pilot plant scale consisting of a membrane biological reactor (MBR) and photocatalytic reactor (PCR) acting in series. The MBR contributed for approximately 70% to the overall slop purification. More precisely, the biological process was able to remove approximately 40%, on average, of the organic pollution in the slop. Nevertheless, the membrane was capable to retain a large amount of organic molecules within the system, amounting for a further 30% of the influent total organic content removal. However, this affected the membrane fouling, thus resulting in the increase of the pore blocking mechanism that accounted for approximately 20% to the total resistance to filtration (2.85∙10 13 m −1 ), even if a significant restoration of the original membrane permeability was obtained after chemical cleanings. On the other hand, the biological treatment produced a clear solution for the photocatalytic system, thereby optimizing the light penetration and generation of highly oxidizing active oxygen species that enabled the degradation of bio-recalcitrant compounds. Indeed, low total organic carbon (TOC) values (<10 mg L −1 ) were achieved in the output of the photocatalytic reactor by means of only 60 Einstein (E) of cumulative impinging energy after the addition of K 2 S 2 O 8 . Overall, coupling the two processes enabled very high TOC removal (ca. 95%)

    N-TiO2 Photocatalysts highly active under visible irradiation for NOX abatement and 2-propanol oxidation

    Get PDF
    N-doped TiO2 powders were prepared by two different sol–gel methods. Samples were characterised by X-ray diffraction (XRD), BET specific surface area measurements (SSA), scanning electron microscopy (SEM), diffuse reflectance spectroscopy (DRS), X-ray photoelectron spectroscopy (XPS) and Electron Paramagnetic Resonance (EPR). XPS measurements revealed a signal at 400 eV assignable to nitrogen in the form of Ti N O. EPR signals are attributed to molecular NO trapped with cavities/defects possibly interacting with oxygen vacancies. The photocatalytic activity under UV and visible light was determined following the abatement of NOx and the photodegradation of 2-propanol in gas–solid systems. N-doped TiO2 showed a higher activity compared with the pristine commercial and home prepared samples under visible light irradiation. A good photoactivity in the abatement of both NOx and 2-propanol is also observed for mechanical dispersions of N-TiO2 in CaCO3 serving as a model in view of perspective application in photocatalytically active construction and architectural materials

    Overview on oxidation mechanisms of organic compounds by TiO2 in heterogeneous photocatalysis

    Get PDF
    This review provides the reader with a general overview on heterogeneous photocatalytic oxidation mechanisms in the presence of TiO2, with a special address to conversion of aliphatic and aromatic organic species. The aim was to clarify the steps of the photo-oxidation of the various classes of compounds and to relate them with the properties of the catalysts and the experimental conditions used. Reactions carried out to perform complete degradation and photocatalytic partial oxidations have been deeply discussed. Recent isotopic studies highlighted new reaction pathways concerning partial oxidation of alcohols to aldehyde and oxidation of benzene while EPR investigations confirmed that not only the photogenerated hole but also the OH radicals are involved in the oxidation of the substrates

    Selective aqueous oxidation of aromatic alcohols under solar light in the presence of TiO2 modified with different metal species

    Get PDF
    A set of metals modified TiO2 photocatalysts were prepared starting from titanium tetraisopropoxyde and different metal precursors to study the influence of the addition of the various foreign agents on the physico-chemical and photocatalytic properties of the catalysts. The powders were characterized by X-ray diffraction, Raman spectroscopy, specific surface area measurements, scanning electron microscopy, energy dispersive X-ray spectroscopy, UV–Vis diffuse reflectance spectroscopy, photoluminescence, temperature programmed desorption after CO2 adsorption. The photocatalytic activity was evaluated using as probe reactions the partial oxidation of three aromatic alcohols: benzyl alcohol (BA), 4-methoxy benzyl alcohol (4-MBA), and 4-hydroxy benzyl alcohol (4-HBA) under simulated solar light irradiation. Different oxidation and selectivity values were obtained for the three substrates depending not only on the type of metals but also on the nature and position of the substituent in the phenyl ring of benzyl alcohol. As a general behaviour, the doped samples allowed the achievement of a greater selectivity especially for 4-MBA even if sometimes with minor conversions. The presence of W or Nb was beneficial for both conversion and selectivity for all the substrates with respect to bare TiO2. Graphical abstract: [Figure not available: see fulltext.

    Exploring the photothermo-catalytic performance of brookite tio2-ceo2 composites

    Get PDF
    The thermocatalytic, photocatalytic and photothermo-catalytic oxidation of some volatile organic compounds (VOCs), 2-propanol, ethanol and toluene, was investigated over brookite TiO2-CeO2 composites. The multi-catalytic approach based on the synergistic effect between solar photocatalysis and thermocatalysis led to the considerable decrease in the conversion temperatures of the organic compounds. In particular, in the photothermo-catalytic runs, for the most active samples (TiO2-3 wt% CeO2 and TiO2-5 wt% CeO2). the temperature at which 90% of VOC conversion occurred was about 60â—¦ C, 40â—¦ C and 20â—¦ C lower than in the thermocatalytic tests for 2-propanol, ethanol and toluene, respectively. Furthermore. the addition of cerium oxide to brookite TiO2 favored the total oxidation to CO2 already in the photocatalytic tests at room temperature. The presence of small amounts of cerium oxide allowed to obtain efficient brookite-based composites facilitating the space charge separation and increasing the lifetime of the photogenerated holes and electrons as confirmed by the characterization measurements. The possibility to concurrently utilize the photocatalytic properties of brookite and the redox properties of CeO2, both activated in the photothermal tests, is an attractive approach easily applicable to purify air from VOCs

    Photocatalytic CO2 Reduction in Gas-Solid Regime in the Presence of Bare, SiO2 Supported or Cu-Loaded TiO2 Samples

    Get PDF
    Both commercial and home prepared (HP) TiO2 samples have been tested for the photocatalytic reduction of CO2. (HP) TiO2 powders were prepared by using TiCl4 or Ti(OC4H9)4 as the precursors to obtain HP1 and HP2 samples, respectively. Also HP Cu-loaded and SiO2 supported TiO2 powders were prepared. The HP samples were more active than the commercial ones for the photoreduction of CO2 with and without water vapour. HP1 produced mainly formaldehyde, HP2 principally methane. Acetaldehyde was found to be the primary product obtained when HP1 was supported on SiO2. The addition of Cu increased the photocatalytic reactivity either of bulk and SiO2-supported HP1. In particular, 1 wt % of Cu improved the formaldehyde yield obtained with the bare HP1 by one order of magnitude. Differently, the presence of Cu or SiO2 in the HP2 samples markedly reduced the production of methane

    A solar photothermocatalytic approach for the CO2 conversion: Investigation of different synergisms on CoO-CuO/brookite TiO2-CeO2 catalysts

    Get PDF
    The photoactive features of the least common polymorph of TiO2, i.e. brookite, were combined with the thermocatalytic redox ones of cerium oxide, focusing on the effects of the addition of small amounts of Co-Cu oxides for the solar CO2 conversion. By considering the characterization data, a surface segregation of the hosted metal oxides on the TiO2-CeO2 composite was evidenced, and their presence increased the amount of oxygen vacancies and improved the charge carriers separation. The bimetallic oxides-based sample was the most performing one in the photocatalytic carbon dioxide reduction at room temperature. The formation of carbon monoxide and methane was 5 and 0.5 μmol g−1h−1, respectively, i.e. about 10 times higher than that found with bare brookite. A further enhancement was obtained with the same CoO-CuO/TiO2-CeO2 catalyst applying the photothermal approach. The CO2-TPD and the FTIR measurements highlighted the high interaction between CO2 and the surface sites

    Highly stable defective TiO2-x with tuned exposed facets induced by fluorine: Impact of surface and bulk properties on selective UV/visible alcohol photo-oxidation

    Get PDF
    Titanium dioxide samples were prepared in the presence of different amounts of fluorine via hydrothermal method. It has been found that the presence of fluoride influenced the physico-chemical properties of TiO2 in various ways as polymorphic form stability, surface hydroxylation, generation of hydroxyl radicals under irradiation and formation of Ti3+ centers and oxygen vacancies. The generation rate of [rad]OH radicals was investigated by the photoluminescence technique in the presence of terephthalic acid. X-ray diffractometry indicated that fluorine stabilized the anatase TiO2. X-Ray photoelectron spectroscopy (XPS) revealed the presence of fluorine on the surface and the shift of the valence band edge towards less negative potentials, electron paramagnetic resonance (EPR) confirmed the formation of Ti3+ in the bulk of the photocatalysts, UV–vis spectra showed the extension of the TiO2 photo-response in the visible light region. 2-Propanol degradation and 4-methoxybenzyl alcohol partial oxidation were studied as probe reactions by using the home prepared powders as photocatalysts. Surprisingly, the photocatalytic activity resulted to be mainly affected by [rad]OH radicals formation ability under irradiation, rather than by the presence of {0 0 1} facets, although it cannot be excluded that the latter could influence the ability to form radicals under irradiation

    Facile preparation of CuBi2O4/TiO2 hetero-systems employed for simulated solar-light selective oxidation of 4-methoxybenzyl alcohol model compound

    Get PDF
    The selective photocatalytic oxidation of organic substances is today considered one of the green techniques to synthesize important starting materials in different technological applications. This work reports an efficient, simple and cheap strategy for the synthesis of a new photocatalytic CuBi2O4-TiO2 (CBO/TiO2) heterosystem at room temperature. The prepared powders were characterized by X-ray diffraction (XRD), UV–Vis diffuse reflectance spectra (DRS), field-emission scanning electron microscopy (FE-SEM), X-ray photoelectron spectroscopy (XPS), and electrochemical measurements. The photocatalytic activity was evaluated by performing a probe reaction, namely the partial oxidation of 4-methoxybenzyl alcohol (4-MBA) to 4-methoxybenzaldehyde (4-MBAld) in aqueous solution under irradiation of simulated sunlight. The CBO/TiO2 coupled systems showed a higher photoactivity than the single photocatalysts reaching a selectivity of 45% towards 4‑methoxy-benzaldehyde with an alcohol conversion of 77% after 4 h of irradiation. Furthermore, although a high alcohol conversion was achieved, the selectivity towards 4-MBAld was significant, unlike what has been reported in the literature for many heterogeneous photocatalytic reactions whose selectivity generally decreases significantly with the increasing conversion of the starting alcohol molecule. The improved photocatalytic activity could be attributed to the partial coverage of the TiO2 surface by CBO which reduces the subsequent oxidation of the formed aldehyde

    Multiphase photo-capillary reactors coated with TiO2 films: preparation, characterization and photocatalytic performance

    Get PDF
    Quartz capillaries were assessed as multiphase photocatalytic reactors. The tested reaction was the salicylic acid (2-dihidroxibenzoic acid) oxidation. The catalyst (TiO2) was either in slurry or immobilized by sol-gel method onto the capillary wall. All experiments were conducted under oxygen flow and Taylor flow hydrodynamic regime. TiO2 Films were characterized by Raman spectroscopy, diffuse reflectance UV-Vis spectroscopy and scanning electronic microscopy. The effect of two synthesis variables was established. These variables were volumetric ratio of precursors solutions (i-PrO:2-propanol:nitric acid) and number of capillary coating cycles. These variables were found to importantly affect film homogeneity and oxidation rate. The highest initial reaction rate (106.32x10-6 mol dm-3s-1) was obtained when using the TiO2 as film prepared with a precursors volumetric ratio of 1:15:1 and with two coating cycles. For comparison purposes, the same oxidation process was conducted in a stirred reactor and it was found that the reaction rate value is diminished by almost four times in comparison with that obtained under Taylor flow in the capillary reactor. Selectivity was found to be dependant on the type of catalyst addition, slurry or immobilized. Catalytic films employed in this non-common reaction system were 2 reused three times losing less than 10% of their photocatalytic activity. The photonic efficiency was found to be two orders of magnitude higher in the coated capillary reactor than in the slurry stirred reactor.L. Hurtado acknowledges CONACYT-Mexico the scholarship No. 56499. Project PRODEP for advanced oxidation processes is also acknowledged for financial support
    • …
    corecore