The superconducting proposal for the CS magnet system of FAST: a preliminary analysis of the heat load due to AC losses

FAST (Fusion Advanced Studies Torus), the Italian proposal of a Satellite Facility to ITER, is a compact tokamak (R$_0$ = 1.82 m, a = 0.64 m, triangularity $\delta$ = 0.4) able to investigate non-linear dynamics effects of $\alpha$-particle behavior in burning plasmas and to test technical solutions for the first wall/divertor directly relevant for ITER and DEMO. Currently, ENEA is investigating the feasibility of a superconducting solution for the magnet system. This paper focuses on the analysis of the CS (Central Solenoid) magnet thermal behavior. In particular, considering a superconducting solution for the CS which uses the room available in the resistive design and referring to one of the most severe scenario envisaged for FAST, the heat load of the CS winding pack due to AC losses is preliminarily evaluated. The results provide a tentative baseline for the definition of the strand requirements and conductor design, that can be accepted in order to fulfil the design requirements.Comment: 15 pages, 5 figure

In-situ Undisturbed Sand Sampling by Radial Freezing for Liquefaction Analysis

The authors experimented in laboratory that if radial freezing with free drainage is performed under an effective confining pressure of 100 kPa only an increase of the order of 0.5% of volumetric strain takes place going from the unfrozen to the frozen condition. The sample comes back to the original dimension after thawing. The displacements of the sample were measured by radiographs of a lead shot network properly built inside the sample. The technique suggested by Yoshimi and al. (1977) to freeze in situ a column of saturated sands was also verified and optimized in laboratory by simulating in a full scale test the site conditions. Finally 3.10 m length and 55 cm. diameter sample of saturated sand was frozen at a well studied site by radial freezing technique, then pulled out from the ground by a crane, sawed and stored in a freezer for future laboratory tests

Application of kaolin and italian natural chabasite-rich zeolitite to mitigate the effect of global warming in vitis vinifera l. Cv. sangiovese

High temperatures and the anomalous distribution of rainfall during the growing season may have a negative impact on grapevine yield and berry composition. In recent years, many studies have focused on the application of agronomical techniques to reduce the negative impact of heat waves on secondary metabolites such as phenols. In particular, treatments with kaolin have shown positive effects on reducing canopy temperatures, enhancing the accumulation of anthocyanins. In regard to the above, three treatments were evaluated: untreated control (C), kaolin (CAO), and chabasite-rich zeolitites (ZEO) applications on cv. Sangiovese in order to verify the cooling effects on leaves and bunches, and the impact on gas exchange, yield parameters, berry composition, and on both chemical and sensory notes of wine. Minerals were sprayed twice around the veraison on the entire canopy at a 3% concentration. The results showed that the application of the minerals was able to reduce the berry temperatures in both years of the trial as compared to the untreated control (C), without affecting vine gas exchange, yield, and soluble solid accumulation. Furthermore, the cooling effect determined an increase in anthocyanin on both the grapes and the wine. At testing, CAO and ZEO wines stood out regarding greater color intensity and were preferred by the judges

Mechanical analysis of the ENEA TF coil proposal for the EU DEMO fusion reactor

The design of the superconducting magnet system of the European DEMO fusion reactor is currently being pursued in the framework of the EUROfusion Magnets Work Package (WPMAG). Three alternative winding pack (WP) options for the Toroidal Field Coils (TFCs) are being proposed by different research units, each featuring a different conductor manufacturing technology (react-and-wind vs. wind-and-react) or winding layout (layer vs. pancake). One of the options (namely, WP#2), proposed by Italian ENEA, features a layer-wound WP design adopting a wind-and-react conductor with rectangular cross section with high aspect ratio, obtained squeezing an initially circular conductor. In order to assess the capability of all the TFC components to withstand the electromagnetic loads due to the huge Lorentz forces without any structural failure during the magnet lifetime, the mechanical analysis of the 2016 version of the WP#2 design option is performed here applying a hierarchical approach herein defined as the Stress Recovery Tool (SRT): the Finite Element Analysis (FEA) of a whole magnet (including the casing) is performed at a low computational cost adopting a coarse WP model with smeared (homogenized) properties. The displacements computed on the smeared WP are then used as boundary conditions for a refined FEA of some WP slices, located in selected (critical) poloidal positions, where all the conductors detailed features (jacket, insulations) are properly accounted for

DC and transient current distribution analysis from self-field measurements on ITER PFIS conductor

Current reconstruction in cable-in-conduit conductors (CICC) cables is a crucial issue to determine cables performance in working conditions, and must be performed using inverse problem approaches as direct measurement is not feasible. The current distribution has been studied for the ITER Poloidal Field Insert Sample (PFIS) conductor using annular arrays of Hall probes placed in three different locations along the sample during the test campaign at the SULTAN facility. The measurement apparatus is also described in the paper, together with the approach to current reconstruction

To Splint or Not to Splint Short Dental Implants Under the Same Partial Fixed Prosthesis? One-year Post-loading Data From a Multicentre Randomised Controlled Trial

PURPOSE. To compare the clinical outcomes of two adjacent 6-mm-long dental implants splinted under the same prosthesis (control group) versus two identical implants sup-porting single crowns (test group). MATERIALS AND METHODS. Forty-seven patients with edentulous posterior (premolars and/or molars) jaws received two adjacent 6-mm-long dental implants, which were sub-merged. Four months later, at impression taking, patients were randomised to receive splinted or unsplinted definitive cemented metal-composite prostheses. Unfortunately, four patients died before randomisation and three patients lost five implants, so only 40 patients were randomised, according to a parallel-group design, to have both implants splinted under the same partial fixed prosthesis (19 patients) or with two single crowns (21 patients). Outcome measures were: prosthesis and implant failures, any complica-tions, peri-implant marginal bone level changes and patient satisfaction. Patients were followed-up to 1 year after loading. RESULTS. One patient from the splinted group dropped out. No implant failures occurred after randomisation. One complication occurred in the unsplinted group versus no complications at splinted implants, the difference not being statistically different (Fisher’s exact test P = 1.000; difference in proportions =-0.04; 95% CI-0.16 to 0.09). Both groups presented significant peri-implant marginal bone loss at 1 year after loading (P<0.05), respectively-0.36 (0.45) mm at splinted implants and-0.17 (0.31) mm at unsplinted implan-ts, but there were no statistically significant differences between the two groups (mean difference 0.19 mm; 95% CI-0.10 to 0.48; P = 0.194). All patients were fully or reasonably satisfied with the treatment, with the exception of two patients, both from the splinted group: one patient was not sure about the aesthetics, and another would not undergo the same treatment again. CONCLUSIONS. The present data seems to suggest that up to 1 year after loading the prognosis of short implants, mostly placed in mandibles characterised by dense bone quality, may not be influenced by splinting or not under the same fixed prostheses. Howe-ver, these preliminary results need to be confirmed by larger trials with follow-ups of at least 5 years