In-depth component distribution in electrodeposited alloys and multilayers

It is shown in this overview that modern composition depth profiling methods like secondary neutral mass spectroscopy (SNMS) and glow-discharge – time-of-flight mass spectrometry (GD-ToFMS) can be used to gain highly specific composition depth profile information on electrodeposited alloys. In some cases, cross-sectional transmission electron microscopy was also used for gaining complementary information; nevertheless, the basic component distribution derived with each method exhibited the same basic features. When applying the reverse sputtering direction to SNMS analysis, the near-substrate composition evolution can be revealed with unprecedented precision. Results are presented for several specific cases of electrodeposited alloys and mulitlayers. It is shown that upon d.c. plating from an unstirred solution, the preferentially deposited metal accumulates in the near-substrate zone, and the steady-state alloy composition sets in at about 150-200 nm deposit thickness only. If there is more than one preferentially deposited metal in the alloy, the accumulation zones of these metals occur in the order of the deposition preference. This accumulation zone can be eliminated by well-controlled hydrodynamic conditions (like the application of rotating disc electrodes) or by pulse plating where the systematic decrease in the duty cycle provides a gradual transition from a graded to a uniform composition depth profile. The application of composition depth profile measurements enabled detecting the coincidence in the occurrence of some components in the deposits down to the impurity level. This was exemplified by the GD-ToFMS measurements of Ni-Cu/Cu multilayers where all detected impurities accumulated in the Cu layer. The wealth of information obtained by these methods provides a much more detailed picture than the results normally obtained with bulk analysis through conventional integral depth profiling and help in the elucidation of the side reactions taking place during the plating processes

Magnetic theory, electromagnetism, ferromagnetism

The workshop "Green deal and circular economy challenges of rare earth-based permanent magnets with technical aspects" is organized as part of the EIT project RECO2MAG - Novel grain boundaries engineered resource efficient Nd-Fe-B permanent magnets (financed by EIT KIC Raw Material)

IoT electrochemical sensor with integrated ▫Ni(OH)2–NiNi(OH)_2–Ni▫ nanowires for detecting formaldehyde in tap water

Simple, low-cost methods for sensing volatile organic compounds that leave no trace and do not have a detrimental effect on the environment are able to protect communities from the impacts of contaminants in water supplies. This paper reports the development of a portable, autonomous, Internet of Things (IoT) electrochemical sensor for detecting formaldehyde in tap water. The sensor is assembled from electronics, i.e., a custom-designed sensor platform and developed HCHO detection system based on Ni(OH)2–Ni nanowires (NWs) and synthetic-paper-based, screen-printed electrodes (pSPEs). The sensor platform, consisting of the IoT technology, a Wi-Fi communication system, and a miniaturized potentiostat can be easily connected to the Ni(OH)2–Ni NWs and pSPEs via a three-terminal electrode. The custom-made sensor, which has a detection capability of 0.8 µM/24 ppb, was tested for an amperometric determination of the HCHO in deionized (DI) and tap-water-based alkaline electrolytes. This promising concept of an electrochemical IoT sensor that is easy to operate, rapid, and affordable (it is considerably cheaper than any lab-grade potentiostat) could lead to the straightforward detection of HCHO in tap water

Effects of Ni and Cu Residuals on the Magnetic Properties and Microstructure of SmCo5 Magnets

The effect of Ni/Cu-coating residuals on the magnetic properties and microstructures of samarium–cobalt (SmCo5) magnets was studied. SmCo5 magnets with 0.0, 0.5, 1.0, 2.0, 3.0 and 4.0 wt.% of added Ni/Cu (85 wt.% Ni/15 wt.% Cu) were prepared using a conventional sintering route. The magnetic properties of the magnets were found to be consistent up to 2 wt.% Ni/Cu. Any further increase in the Ni/Cu content resulted in a significant reduction in the magnetic properties, to lower than values that would be commercially acceptable. SEM/EDS studies showed that two major phases, i.e., the SmCo5 matrix phase and Sm2O3 were present in all the sintered SmCo5 magnets. The presence of Sm2Co7 as a minor phase fraction was detected in the sintered SmCo5 magnets containing up to 2 wt.% Ni/Cu. A 2 wt.% Ni/Cu addition to magnets resulted in the presence of two new phases with compositions close to SmCo and Sm2Co17 in addition to SmCo5 and Sm2O3 as major phases in the SEM-observed microstructure. These newly formed phases are present in small fractions and are presumably homogenously distributed at the grain boundaries of the magnets. As they are known to act as nucleation sites for reverse magnetic domains, they effectively reduce the intrinsic grain boundary magnetic strength, leading to a drop in the coercivity. We concluded that the sintered SmCo5 magnets could be recycled with up to 2 wt.% Ni/Cu as a residual from the coating under our sintering and heat treatment conditions

Facile Fabrication of an Ammonia-Gas Sensor Using Electrochemically Synthesised Polyaniline on Commercial Screen-Printed Three-Electrode Systems

Polyaniline (PANI) is a conducting polymer, widely used in gas-sensing applications. Due to its classification as a semiconductor, PANI is also used to detect reducing ammonia gas (NH3), which is a well-known and studied topic. However, easier, cheaper and more straightforward procedures for sensor fabrication are still the subject of much research. In the presented work, we describe a novel, more controllable, synthesis approach to creating NH3 PANI-based receptor elements. The PANI was electrochemically deposited via cyclic voltammetry (CV) on screen-printed electrodes (SPEs). The morphology, composition and surface of the deposited PANI layer on the Au electrode were characterised with electron microscopy, Fourier-transform infrared spectroscopy and profilometry. Prior to the gas-chamber measurement, the SPE was suitably modified by Au sputtering the individual connections between the three-electrode system, thus showing a feasible way of converting a conventional three-electrode electrochemical SPE system into a two-electrode NH3-gas detecting system. The feasibility of the gas measurements’ characterisation was improved using the gas analyser. The gas-sensing ability of the PANI-Au-SPE was studied in the range 32–1100 ppb of NH3, and the sensor performed well in terms of repeatability, reproducibility and sensitivity

Novel organoruthenium(II) complex C1 selectively inhibits butyrylcholinesterase without side effects on neuromuscular transmission

Enzyme butyrylcholinesterase (BChE) shows increased activity in some brain regions after progression of Alzheimer’s disease and is therefore one of the therapeutic targets for symptomatic treatment of this neurodegenerative disorder. The organoruthenium(II) complex [(n6-pcymene) Ru(II)(1-hydroxy-3-methoxypyridine-2(1H)-thionato)pta]PF6 (C1) was designed based on the results of our previous structure–activity studies. Inhibitory activity toward cholinesterase enzymes shows that this complex selectively, competitively, and reversibly inhibits horse serum BChE (hsBChE) with an IC50 value of 2.88 μM. When tested at supra-pharmacological concentrations (30, 60, 90, and 120 μM), C1 had no significant effect on the maximal amplitude of nerve-evoked and directly elicited single-twitch and tetanic contractions. At the highest tested concentration (120 μM), C1 had no effect on resting membrane potential, but significantly decreased the amplitude of miniature endplate potentials (MEPP) without reducing their frequency. The same concentration of C1 had no effect on the amplitude of end-plate potentials (EPP), however it shortened the half-decay time of MEPPs and EPPs. The decrease in the amplitude of MEPPs and shortening of the half-decay time of MEPPs and EPPs suggest a possible weak inhibitory effect on muscle-type nicotinic acetylcholine receptors (nAChR). These combined results show that, when applied at supra-pharmacological concentrations up to 120 μM, C1 does not importantly affect the physiology of neuromuscular transmission and skeletal muscle contraction

Novel Organoruthenium(II) Complex C1 Selectively Inhibits Butyrylcholinesterase without Side Effects on Neuromuscular Transmission

Enzyme butyrylcholinesterase (BChE) shows increased activity in some brain regions after progression of Alzheimer’s disease and is therefore one of the therapeutic targets for symptomatic treatment of this neurodegenerative disorder. The organoruthenium(II) complex [(η6-p-cymene)Ru(II)(1-hydroxy-3-methoxypyridine-2(1H)-thionato)pta]PF6 (C1) was designed based on the results of our previous structure–activity studies. Inhibitory activity toward cholinesterase enzymes shows that this complex selectively, competitively, and reversibly inhibits horse serum BChE (hsBChE) with an IC50 value of 2.88 µM. When tested at supra-pharmacological concentrations (30, 60, 90, and 120 µM), C1 had no significant effect on the maximal amplitude of nerve-evoked and directly elicited single-twitch and tetanic contractions. At the highest tested concentration (120 µM), C1 had no effect on resting membrane potential, but significantly decreased the amplitude of miniature end-plate potentials (MEPP) without reducing their frequency. The same concentration of C1 had no effect on the amplitude of end-plate potentials (EPP), however it shortened the half-decay time of MEPPs and EPPs. The decrease in the amplitude of MEPPs and shortening of the half-decay time of MEPPs and EPPs suggest a possible weak inhibitory effect on muscle-type nicotinic acetylcholine receptors (nAChR). These combined results show that, when applied at supra-pharmacological concentrations up to 120 µM, C1 does not importantly affect the physiology of neuromuscular transmission and skeletal muscle contraction

Online course: Green deal and circular economy challenges of rare earth-based permanent magnets with technical aspects

The workshop "Green deal and circular economy challenges of rare earth-based permanent magnets with technical aspects" is organized as part of the EIT project RECO2MAG - Novel grain boundaries engineered resource efficient Nd-Fe-B permanent magnets (financed by EIT KIC Raw Material)

Online course: Rare Earth Elements value chain gaps and opportunities in the ADRIA region

The workshop "Rare Earth Elements value chain gaps and opportunities in the ADRIA region" is organized as part of the EIT project RECO2MAG - Novel grain boundaries engineered resource efficient Nd-Fe-B permanent magnets (financed by EIT KIC Raw Material)

The Future of Permanent-Magnet-Based Electric Motors: How Will Rare Earths Affect Electrification?

In this review article, we focus on the relationship between permanent magnets and the electric motor, as this relationship has not been covered in a review paper before. With the increasing focus on battery research, other parts of the electric system have been neglected. To make electrification a smooth transition, as has been promised by governing bodies, we need to understand and improve the electric motor and its main component, the magnet. Today’s review papers cover only the engineering perspective of the electric motor or the material-science perspective of the magnetic material, but not both together, which is a crucial part of understanding the needs of electric-motor design and the possibilities that a magnet can give them. We review the road that leads to today’s state-of-the-art in electric motors and magnet design and give possible future roads to tackle the obstacles ahead and reach the goals of a fully electric transportation system. With new technologies now available, like additive manufacturing and artificial intelligence, electric motor designers have not yet exploited the possibilities the new freedom of design brings. New out-of-the-box designs will have to emerge to realize the full potential of the new technology. We also focus on the rare-earth crisis and how future price fluctuations can be avoided. Recycling plays a huge role in this, and developing a self-sustained circular economy will be critical, but the road to it is still very steep, as ongoing projects show