Morphology and function of human Leydig cells in vitro. Immunocytochemical and radioimmunological analyses

The aim of our study was to show whether the cells isolated from testes of patients underwent bilateral orchiectomy for prostatic cancer are able to grown in vitro, and if so, are functionally active. Immuncytochemistry was performed to show the functional status of human cultured cells. In detail, immunolocalization of luteinizing hormone receptors (LHR), mitochondria, and cytoskeletal elements was demonstrated. Moreover, radioimmunological assay was used to measure testosterone secretion by cultured Leydig cells. Using Nomarski interference contrast and fine immunofluorescence analysis the positive immunostaining for LHR was observed in almost all Leydig cells, however it was of various intensity in individual cells. Testosterone measurement revealed significant difference between testosterone secretion by hCG-stimulated and unstimulated Leydig cells (p<0.05). Moreover, testosterone levels were significantly higher in 24- and 48-hour-cultures than in those of 72 hrs (p<0.05). Morphological analysis of Leydig cells in culture revealed the presence of mononuclear and multinucleate cells. The latter cells occurred in both hCG-stimulated and unstimulated cultures. In Leydig cells labeled with a molecular marker MitoTtracker, an abundance of mitochondria and typical distribution of microtubules and microfilaments were observed irrespective of the number of nuclei within the cell, suggesting no functional differences between mono- and multinucleate human Leydig cells in vitro. Since the percentage of multinucleate cells was similar in both hCG-stimulated and unstimulated cultures (23.70% and 22.80%), respectively, the appearance of these cell population seems to be independent of hormonal stimulation

Thermo-hydraulic modeling of the ITER radial neutron camera

The ITER Radial Neutron Camera (RNC) is a diagnostic system designed as a multichannel detection system to measure the uncollided neutron flux from the plasma, generated in the tokamak vacuum vessel, providing information on neutron emissivity profile. The RNC consists of array of cylindrical collimators located in two diagnostic structures: the ex-port system and the in-port system. The in-port system, contains the diamond detectors which need a temperature protection. Feasibility study of the efficiency of the cooling system for the In-port Detector Modules of the RNC during baking process was the main goal of thermo-hydraulic numerical modeling. The paper presents the concept of the cooling system layout and the original way of integration of numerical thermo-hydraulic analyses of the in-port detector cassette. Due to the large extent of the detector cassette it is impossible to include all relevant thermal and hydraulic effects in one global model with sufficient level of details. Thus the modelling strategy is based on the concept of three stage modelling from details to global model. The presented paper includes results of numerical calculations made with ANSYS Fluent software in order to provide the final answer, including calculation of heat loads in the detector cassette from adjacent walls during baking and normal operation conditions

Mapping localized surface plasmons within silver nanocubes using cathodoluminescence hyperspectral imaging

Localized surface plasmons within silver nanocubes less than 50 nm in size are investigated using high resolution cathodoluminescence hyperspectral imaging. Multivariate statistical analysis of the multidimensional luminescence dataset allows both the identification of distinct spectral features in the emission and the mapping of their spatial distribution. These results show a 490 nm peak emitted from the cube faces, with shorter wavelength luminescence coming from the vertices and edges; this provides direct experimental confirmation of theoretical predictions

Measurement of shower development and its Moli\`ere radius with a four-plane LumiCal test set-up

A prototype of a luminometer, designed for a future e+e- collider detector, and consisting at present of a four-plane module, was tested in the CERN PS accelerator T9 beam. The objective of this beam test was to demonstrate a multi-plane tungsten/silicon operation, to study the development of the electromagnetic shower and to compare it with MC simulations. The Moli\`ere radius has been determined to be 24.0 +/- 0.6 (stat.) +/- 1.5 (syst.) mm using a parametrization of the shower shape. Very good agreement was found between data and a detailed Geant4 simulation.Comment: Paper published in Eur. Phys. J., includes 25 figures and 3 Table

Performance of fully instrumented detector planes of the forward calorimeter of a Linear Collider detector

Detector-plane prototypes of the very forward calorimetry of a future detector at an e+e- collider have been built and their performance was measured in an electron beam. The detector plane comprises silicon or GaAs pad sensors, dedicated front-end and ADC ASICs, and an FPGA for data concentration. Measurements of the signal-to-noise ratio and the response as a function of the position of the sensor are presented. A deconvolution method is successfully applied, and a comparison of the measured shower shape as a function of the absorber depth with a Monte-Carlo simulation is given.Comment: 25 pages, 32 figures, revised version following comments from referee

Luminometer for the future International Linear Collider - simulation and beam test results

LumiCal will be the luminosity calorimeter for the proposed International Large Detector of the International Linear Collider (ILC). The ILC physics program requires the integrated luminosity to be measured with a relative precision on the order of 10e-3, or 10e-4 when running in GigaZ mode. Luminosity will be determined by counting Bhabha scattering events coincident in the two calorimeter modules placed symmetrically on opposite sides of the interaction point. To meet these goals, the energy resolution of the calorimeter must be better than 1.5% at high energies. LumiCal has been designed as a 30-layer sampling calorimeter with tungsten as the passive material and silicon as the active material. Monte Carlo simulation using the Geant4 software framework has been used to identify design elements which adversely impact energy resolution and correct for them without loss of statistics. BeamCal, covering polar angles smaller than LumiCal, will serve for beam tuning, luminosity optimisation and high energy electron detection. Secondly, prototypes of the sensors and electronics for both detectors have been evaluated during beam tests, the results of which are also presented here.Comment: Technology and Instrumentation in Particle Physics 2011, Chicago, IL, USA. Presented June 11, 2011, and submitted to Physics Procedi

ECFA Detector R&D Panel, Review Report

Two special calorimeters are foreseen for the instrumentation of the very forward region of an ILC or CLIC detector; a luminometer (LumiCal) designed to measure the rate of low angle Bhabha scattering events with a precision better than 10$^{-3}$ at the ILC and 10$^{-2}$ at CLIC, and a low polar-angle calorimeter (BeamCal). The latter will be hit by a large amount of beamstrahlung remnants. The intensity and the spatial shape of these depositions will provide a fast luminosity estimate, as well as determination of beam parameters. The sensors of this calorimeter must be radiation-hard. Both devices will improve the e.m. hermeticity of the detector in the search for new particles. Finely segmented and very compact electromagnetic calorimeters will match these requirements. Due to the high occupancy, fast front-end electronics will be needed. Monte Carlo studies were performed to investigate the impact of beam-beam interactions and physics background processes on the luminosity measurement, and of beamstrahlung on the performance of BeamCal, as well as to optimise the design of both calorimeters. Dedicated sensors, front-end and ADC ASICs have been designed for the ILC and prototypes are available. Prototypes of sensor planes fully assembled with readout electronics have been studied in electron beams.Comment: 61 pages, 51 figure

Development and test of a segmented Time-of-Flight plastic detector

Path planning problems involve computing or finding a collision free path between two positions. A special kind of path planning is complete coverage path planning, where a robot sweeps all area of free space in an environment. There are different methods to cover the complete area; however, they are not designed to optimize the process. This paper proposes a novel method of complete coverage path planning based on genetic algorithms. In order to check the viability of this approach the optimal path is tested in a virtual environment. The simulation results confirm the feasibility of this method