Computer aided processing using laser measurements

The challenge exists of processing the STS and its cargo through KSC facilities in the most timely and cost effective manner possible. To do this a 3-D computer graphics data base was established into which was entered the STS, payloads, and KSC facilities. The facility drawing data are enhanced by laser theodolite measurements into an as-built configuration. Elements of the data base were combined to study orbiter/facility interfaces payload/facility access problems and design/arrangement of various GSE to support processing requirements. With timely analysis/design utilizing the 3-D computer graphics system, costly delays can be avoided. Better methodology can be analyzed to determine procedures for cost avoidance

Multispectral scanner optical system

An optical system for use in a multispectral scanner of the type used in video imaging devices is disclosed. Electromagnetic radiation reflected by a rotating scan mirror is focused by a concave primary telescope mirror and collimated by a second concave mirror. The collimated beam is split by a dichroic filter which transmits radiant energy in the infrared spectrum and reflects visible and near infrared energy. The long wavelength beam is filtered and focused on an infrared detector positioned in a cryogenic environment. The short wavelength beam is dispersed by a pair of prisms, then projected on an array of detectors also mounted in a cryogenic environment and oriented at an angle relative to the optical path of the dispersed short wavelength beam

Evaluation of range and distortion tolerance for high Mach number transonic fan stages. Task 2: Performance of a 1500-foot-per-second tip speed transonic fan stage with variable geometry inlet guide vanes and stator

A 0.5 hub/tip radius ratio compressor stage consisting of a 1500 ft/sec tip speed rotor, a variable camber inlet guide vane and a variable stagger stator was designed and tested with undistorted inlet flow, flow with tip radial distortion, and flow with 90 degrees, one-per-rev, circumferential distortion. At the design speed and design IGV and stator setting the design stage pressure ratio was achieved at a weight within 1% of the design flow. Analytical results on rotor tip shock structure, deviation angle and part-span shroud losses at different operating conditions are presented. The variable geometry blading enabled efficient operation with adequate stall margin at the design condition and at 70% speed. Closing the inlet guide vanes to 40 degrees changed the speed-versus-weight flow relationship along the stall line and thus provided the flexibility of operation at off-design conditions. Inlet flow distortion caused considerable losses in peak efficiency, efficiency on a constant throttle line through design pressure ratio at design speed, stall pressure ratio, and stall margin at the 0 degrees IGV setting and high rotative speeds. The use of the 40 degrees inlet guide vane setting enabled partial recovery of the stall margin over the standard constant throttle line

Acoustic signatures of the seafloor: Tools for predicting grouper habitat

Groupers are important components of commercial and recreational fisheries. Current methods of diver-based grouper census surveys could potentially benefit from development of remotely sensed methods of seabed classification. The goal of the present study was to determine if areas of high grouper abundance have characteristic acoustic signatures. A commercial acoustic seabed mapping system, QTC View Series V, was used to survey an area near Carysfort Reef, Florida Keys. Acoustic data were clustered using QTC IMPACT software, resulting in three main acoustic classes covering 94% of the area surveyed. Diver-based data indicate that one of the acoustic classes corresponded to hard substrate and the other two represented sediment. A new measurement of seabed heterogeneity, designated acoustic variability, was also computed from the acoustic survey data in order to more fully characterize the acoustic response (i.e., the signature) of the seafloor. When compared with diver-based grouper census data, both acoustic classification and acoustic variability were significantly different at sites with and without groupers. Sites with groupers were characterized by hard bottom substrate and high acoustic variability. Thus, the acoustic signature of a site, as measured by acoustic classification or acoustic variability, is a potentially useful tool for stratifying diver sampling effort for grouper census

Energy efficient engine: Preliminary design and integration studies

Parametric design and mission evaluations of advanced turbofan configurations were conducted for future transport aircraft application. Economics, environmental suitability and fuel efficiency were investigated and compared with goals set by NASA. Of the candidate engines which included mixed- and separate-flow, direct-drive and geared configurations, an advanced mixed-flow direct-drive configuration was selected for further design and evaluation. All goals were judged to have been met except the acoustic goal. Also conducted was a performance risk analysis and a preliminary aerodynamic design of the 10 stage 23:1 pressure ratio compressor used in the study engines

Advanced indium antimonide monolithic charge coupled infrared imaging arrays

The continued process development of SiO2 insulators for use in advanced InSb monolithic charge coupled infrared imaging arrays is described. Specific investigations into the use of plasma enhanced chemical vapor deposited (PECVD) SiO2 as a gate insulator for InSb charge coupled devices is discussed, as are investigations of other chemical vapor deposited SiO2 materials

Modeling 3-D objects with planar surfaces for prediction of electromagnetic scattering

Electromagnetic scattering analysis of objects at resonance is difficult because low frequency techniques are slow and computer intensive, and high frequency techniques may not be reliable. A new technique for predicting the electromagnetic backscatter from electrically conducting objects at resonance is studied. This technique is based on modeling three dimensional objects as a combination of flat plates where some of the plates are blocking the scattering from others. A cube is analyzed as a simple example. The preliminary results compare well with the Geometrical Theory of Diffraction and with measured data

Observations on the Overwintering Potential of the Striped Cucumber Beetle (Coleoptera: Chrysomelidae) in Southern Minnesota

The striped cucumber beetle, Acalymma vittatum (Fabricius) (Coleoptera: Chrysomelidae), is an important pest of cucurbit crops. However, the overwinter- ing capacity of this pest in temperate regions is poorly understood. In this study, the in-field survival of A. vittatum was examined during three consecutive winters. In addition, the supercooling points of A. vittatum were determined as an index of cold hardiness for adults. During each winter, the survival of adults decreased significantly through time, with no individuals surviving until spring. By comparing the supercooling points and in-field survival of adults to soil temperatures, it appears that winter temperatures in Minnesota are cold enough to induce freezing of the beetles. Moreover, a considerable amount of mortality occurred before minimum monthly soil temperatures dropped below the supercooling point of overwintering individuals, suggesting the occurrence of prefreeze mortality. An improved understanding of the response of A. vittatum to winter temperatures in temperate regions may aid in early season management of this pest