Simulator evaluation of a flight-path-angle control system for a transport airplane with direct lift control

A piloted simulator was used to evaluate the flight path angle control capabilities of a system that employs spoiler direct lift control. The system was designated the velocity vector control system and was compared with a baseline flight path angle control system which used elevator for control. The simulated airplane was a medium jet transport. Research pilots flew a manual instrument landing system glide slope tracking task and a variable flight path angle task in the landing configuration to obtain comparative performance data

Limited evaluation of an F-14A airplane utilizing an aileron-rudder interconnect control system in the landing configuration

A flight test was conducted for preliminary evaluation of an aileron-rudder interconnect (ARI) control system for the F-14A airplane in the landing configuration. Two ARI configurations were tested in addition to the standard F-14 flight control system. Results of the flight test showed marked improvement in handling qualities when the ARI systems were used. Sideslip due to adverse yaw was considerably reduced, and airplane turn rate was more responsive to pilot lateral control inputs. Pilot comments substantiated the flight data and indicated that the ARI systems were superior to the standard control system in terms of pilot capability to make lateral offset corrections and heading changes on final approach

Effect on head-wind profiles and mean head-wind velocity on landing capacity flying constant-airspeed and constant-groundspeed approaches

A study was conducted to determine the effect of head-wind profiles and mean head-wind velocities on runway landing capacity for airplanes flying constant-airspeed and constant-groundspeed approaches. It was determined that when the wind profiles were encountered with the currently used constant airspeed approach method, the landing capacity was reduced. The severity of these reductions increased as the mean head-wind value of the profile increased. When constant-groundspeed approaches were made in the same wind profiles, there were no losses in landing capacity. In an analysis of mean head winds, it was determined that in a mean head wind of 35 knots, the landing capacity using constant-airspeed approaches was 13% less than for the no wind condition. There were no reductions in landing capacity with constant-groundspeed approaches for mean head winds less than 35 knots. This same result was observed when the separation intervals between airplanes was reduced

A failsafe analysis using NASTRAN's piecewise linear analysis and a nine node linear crack element

A two-dimensional crack element was implemented into NASTRAN as a user dummy element and used to study failsafe characteristics of the C5A fuselage. The element is formulated from Reitsner's functional requiring that it satisfy compatability with the linear boundary displacement elements in NASTRAN. Its accuracy is demonstrated by analyzing for the stress intensity factors of two simple crack configurations for which there are classic solutions

Results of a simulator test comparing two display concepts for piloted flight-path-angle control

Results of a simulator experiment which was conducted in order to compare pilot gamma-control performance using two display formats are reported. Pilots flew a variable flight path angle tracking task in the landing configuration. Pilot and airplane performance parameters were recorded and pilot comments noted for each case

Simulation study to evaluate a constant-groundspeed approach method in moderate and severe wind shears

The use of a constant-groundspeed procedure for flying final approaches in moderate and severe wind shear environments was investigated. Performance was compared to results of simulated constant-airspeed approaches in identical wind profiles. The simulation model was a medium twin-jet transport equipped with an autothrottle for maintaining constant groundspeed or constant airspeed. For both moderate and severe wind shears, the constant-groundspeed approach method was shown to provide a way to more safely negotiate the shears while also providing predictable and acceptable touchdown performance. Results showed airspeeds on final approach to be considerably higher using the constant-groundspeed method, which supplied the additional stall margin needed when tail-wind shears were encountered. Throttle movements were noticeably reduced in all wind profiles when constant-groundspeed approaches were flown. Touchdown conditions were practically identical for both approach methods in moderate wind shear

Examination of accelerated first order methods for aircraft flight path optimization

Accelerated first order methods for aircraft flight path optimizatio

Development of an orthotropic hole element

A finite element was developed which adequately represents the state of stress in the region around a circular hole in orthotropic material experiencing reasonably general loading. This was achieved with a complementary virtual work formulation of the stiffness and stress matrices for a square element with center circular hole. The assumed stress state provides zero shearing stress on the hole boundary, so the element is suitable for problems involving load transfer without friction. The element has been implemented in the NASTRAN computer program, and sample problem results are presented

Borderplex Economic Outlook: 2006 – 2008

A variety of measures such as real output, retail receipts, and personal incomes show how the borderplex economy continues to expand (Table 1). Although employment growth is expected to subside, local labor market strength will be sufficiently robust to hold the El Paso unemployment rate well below its 32-year average of greater than 10 percent. Similarly, even though residential construction activity is expected to moderate slightly, overall housing activity is projected to remain high by historical standards. Expansion at Fort Bliss is the source for much of the heightened business activity as the arrivals of new troops translate into greater demand for housing, retail, and other services. By 2008, more than 13 thousand businesses are expected to be registered in El Paso. Per capita personal income is projected to exceed $26,200 that year. Additional detail obtained from simulations of the UTEP Borderplex Econometric Forecasting Model is presented below for El Paso, Ciudad Juarez, Chihuahua City, and Las Cruces.U.S. - Mexico Border Region; Econometric Forecasts