41 research outputs found
Development of Tannin Modified Membrane for Spectrophotometric Determination of Lead
Tannin modified membrane (TM) was developed for preconcentration and detection of trace level of lead (Pb) using a complex formation between Pb2+ and (4-2-pyridylazo)-resorcinol (PAR). The extraction membrane was prepared by immobilizing tannin on a rectangular cellulose filter paper sized 7 x 9 cm2 and then cut into a small circular shape of 13-mm diameter to fit with a commercially available syringe filter holder. The 4-layered of the TMs was employed for preconcentration of Pb2+. An aliquot of 50 mL of standard or sample containing Pb2+ was loaded by using a 50-mL syringe that connected with a filter holder. To accelerate speed of analysis, peristaltic pump was used by connecting to a bottom side of the filter holder. For loading step, a flow rate of 4.4 mL/min was used. Elution of Pb2+ was accomplished by manually passing 5 mL of 0.1 M HCl through the membrane. An aliquot of 3 mL of the eluent was then mixed with the PAR reagent under the controlled pH of 9. Absorbance of 522 nm was monitored. Various optimization parameters affecting the immobilization of tannin on the cellulose filter paper were investigated. Under optimized conditions, linear calibration was obtained from 0.1 mg/L to 1.25 mg/L of Pb2+ solution. Acceptable precision of 2.0% (n = 5) was obtained. Good recoveries of 90.40 and 91.99 were achieved for drinking water samples
High Sensitivity Electrochemical Cholesterol Sensor Utilizing a Vertically Aligned Carbon Nanotube Electrode with Electropolymerized Enzyme Immobilization
In this report, a new cholesterol sensor is developed based on a vertically aligned CNT electrode with two-step electrochemical polymerized enzyme immobilization. Vertically aligned CNTs are selectively grown on a 1 mm2 window of gold coated SiO2/Si substrate by thermal chemical vapor deposition (CVD) with gravity effect and water-assisted etching. CNTs are then simultaneously functionalized and enzyme immobilized by electrochemical polymerization of polyaniline and cholesterol enzymes. Subsequently, ineffective enzymes are removed and new enzymes are electrochemically recharged. Scanning electron microscopic characterization indicates polymer-enzyme nanoparticle coating on CNT surface. Cyclic voltammogram (CV) measurements in cholesterol solution show the oxidation and reduction peaks centered around 450 and −220 mV, respectively. An approximately linear relationship between the cholesterol concentration and the response current could be observed in the concentration range of 50–300 mg/dl with a sensitivity of approximately 0.22 μA/mg·dl−1, which is considerably higher compared to previously reported CNT bioprobe. In addition, good specificity toward glucose, uric acid acetaminophen and ascorbic acid have been obtained. Moreover, sensors have satisfactory stability, repeatability and life time. Therefore, the electropolymerized CNT bioprobe is promising for cholesterol detection in normal cholesterol concentration in human blood
Pulsed Amperometry for Anti-fouling of Boron-doped Diamond in Electroanalysis of β-Agonists: Application to Flow Injection for Pharmaceutical Analysis
This work presents the construction and application of boron-doped diamond(BDD) thin film electrode as sensor for the determination of three β-agonists, viz.salbutamol, terbutaline and clenbuterol. Although well-known as a chemically inertmaterial, BDD film however shows fouling in detection of these compounds using fixedpotentialmode amperometry. A suitable waveform for pulsed amperometric detection(PAD) was developed and used to determine the agonist compounds. It was seen that thedeveloped PAD significantly refreshed the BDD surface for long-term detection in flowinjection analysis. Linear working ranges were 0.5-100 μM, 1.0-100 μM and 0.5-50 μM forsalbutamol, terbutaline and clenbuterol, respectively. The developed PAD-BDD system wasapplied to successfully determine salbutamol and terbutaline in commercial pharmaceuticalproducts. The methods were validated with a capillary electrophoresis method
A label-free electrochemical biosensor for the detection of alpha-thalassemia 1 (SEA deletion) carriers using screen-printed carbon electrodes
A label-free electrochemical DNA biosensor based on electrochemical impedance spectroscopy (EIS) biosensor has been extensively developed for diagnosing human genetic diseases. However, its application has been limited to simulated target DNA. The aim of this study was to develop an EIS biosensor that can identify carriers of alpha (α)-thalassemia 1 with Southeast Asia (SEA) deletion. The biosensor was coupled with screen-printed carbon electrodes (SPCEs) and Hoechst 33,258 dye. To determine the optimal conditions and cutoff criteria, we evaluated forty samples with known DNA genotypes. Our findings suggested that the cutoff value for identifying α-thalassemia 1 (SEA deletion) carriers was more than 26.84 kΩ of negative imaginary impedance (-Z″) and 48.83 kΩ of charge transfer resistance (Rct). The sensitivity of the developed EIS biosensor was comparable to that of conventional gel electrophoresis, with no cross-reactivity observed in α-thalassemia 1 (THAI deletion), α-thalassemia 2 (3.7 deletion), α-thalassemia 2 (4.2 deletion), and beta (β)-thalassemia carriers. The diagnostic potential of the developed EIS biosensor was evaluated using 81 clinical blood samples, demonstrating 100% sensitivity, 88.2% specificity, 83.3% positive predictive value (PPV), 100% negative predictive value (NPV) and 92.6% accuracy for Rct measurement. The developed EIS biosensor presents an attractive screening method for the detecting α-thalassemia 1 (SEA deletion) carriers due to its simplicity, cost-effectiveness, and 45-fold reduction in turnaround time compared to conventional gel electrophoresis. Consequently, the identification of α-thalassemia 1 (SEA deletion) carrier through this approach represents the most effective strategy for the management and prevention of the most severe form of thalassemia
Non-Enzymatic Amperometric Glucose Sensor Based on Carbon Nanodots and Copper Oxide Nanocomposites Electrode
In this research work, a non-enzymatic amperometric sensor for the determination of glucose was designed based on carbon nanodots (C-dots) and copper oxide (CuO) nanocomposites (CuO-C-dots). The CuO-C-dots nanocomposites were modified on the surface of a screen-printed carbon electrode (SPCE) to increase the sensitivity and selectivity of the glucose sensor. The as-synthesized materials were further analyzed for physico-chemical properties through characterization tools such as transmission electron microscopy (TEM) and Fourier-transform infrared spectroscopy (FTIR); and their electrochemical performance was also studied. The SPCE modified with CuO-C-dots possess desirable electrocatalytic properties for glucose oxidation in alkaline solutions. Moreover, the proposed sensing platform exhibited a linear range of 0.5 to 2 and 2 to 5 mM for glucose detection with high sensitivity (110 and 63.3 µA mM−1cm−2), and good selectivity and stability; and could potentially serve as an effective alternative method of glucose detection
Paper-Based Screen-Printed Ionic-Liquid/Graphene Electrode Integrated with Prussian Blue/MXene Nanocomposites Enabled Electrochemical Detection for Glucose Sensing
As glucose biosensors play an important role in glycemic control, which can prevent the diabetic complications, the development of a glucose sensing platform is still in needed. Herein, the first proposal on the in-house fabricated paper-based screen-printed ionic liquid/graphene electrode (SPIL-GE) modified with MXene (Ti3C2Tx), prussian blue (PB), glucose oxidase (GOx), and Nafion is reported. The concentration of PB/Ti3C2Tx was optimized and the optimal detection potential of PB/Ti3C2Tx/GOx/Nafion/SPIL-GE is −0.05 V. The performance of PB/Ti3C2Tx/GOx/Nafion modified SPIL-GE was characterized by cyclic voltammetry and chronoamperometry technique. This paper-based platform integrated with nanomaterial composites were realized for glucose in the range of 0.0–15.0 mM with the correlation coefficient R2 = 0.9937. The limit of detection method and limit of quantification were 24.5 μM and 81.7 μM, respectively. In the method comparison, this PB/Ti3C2Tx/GOx/Nafion/SPIL-GE exhibits a good correlation with the reference hexokinase method. This novel glucose sensing platform can potentially be used for the good practice to enhance the sensitivity and open the opportunity to develop paper-based electroanalytical devices