105,006 research outputs found
Measurements at 13.9 GHz of the radar backscattering cross section of the North Sea covered with an artificial surface film
The reduction of the Ku‐band (13.9 GHz) normalized radar cross section (NRCS) by an artificial monomolecular surface film (oleyl alcohol) on the sea surface was measured in the North Sea during the 1975 Joint North Sea Wave Project, JONSWAP 75 experiment. The aim of the surface film experiment was to simulate natural surface films which often occur on the ocean surface and are produced by plankton or fish. NRCS measurements were obtained from an aircraft at incidence angles of 41° and 47° at vertical and horizontal polarizations. For winds between 3.5 and 4.4 m/sec the maximum measured reduction was 7.3 ± 3.5 dB relative to the mean. In‐situ measurements showed that the oleyl alcohol film reduced the surface tension from 74 to 43 dyne/cm. Similar reductions in surface tension have also been measured on the ocean due to natural surface films of biological origin. It is noted that variations of the NRCS due to natural surface film effects may significantly limit the techniques used currently to infer surface wind vector over biologically active ocean regions
Parallel, Asynchronous Executive (PAX): System concepts, facilities, and architecture
The Parallel, Asynchronous Executive (PAX) is a software operating system simulation that allows many computers to work on a single problem at the same time. PAX is currently implemented on a UNIVAC 1100/42 computer system. Independent UNIVAC runstreams are used to simulate independent computers. Data are shared among independent UNIVAC runstreams through shared mass-storage files. PAX has achieved the following: (1) applied several computing processes simultaneously to a single, logically unified problem; (2) resolved most parallel processor conflicts by careful work assignment; (3) resolved by means of worker requests to PAX all conflicts not resolved by work assignment; (4) provided fault isolation and recovery mechanisms to meet the problems of an actual parallel, asynchronous processing machine. Additionally, one real-life problem has been constructed for the PAX environment. This is CASPER, a collection of aerodynamic and structural dynamic problem simulation routines. CASPER is not discussed in this report except to provide examples of parallel-processing techniques
Increasing processor utilization during parallel computation rundown
Some parallel processing environments provide for asynchronous execution and completion of general purpose parallel computations from a single computational phase. When all the computations from such a phase are complete, a new parallel computational phase is begun. Depending upon the granularity of the parallel computations to be performed, there may be a shortage of available work as a particular computational phase draws to a close (computational rundown). This can result in the waste of computing resources and the delay of the overall problem. In many practical instances, strict sequential ordering of phases of parallel computation is not totally required. In such cases, the beginning of one phase can be correctly computed before the end of a previous phase is completed. This allows additional work to be generated somewhat earlier to keep computing resources busy during each computational rundown. The conditions under which this can occur are identified and the frequency of occurrence of such overlapping in an actual parallel Navier-Stokes code is reported. A language construct is suggested and possible control strategies for the management of such computational phase overlapping are discussed
Theoretical and subjective bit assignments in transform picture
It is shown that all combinations of symmetrical input distributions with difference distortion measures give a bit assignment rule identical to the well-known rule for a Gaussian input distribution with mean-square error. Published work is examined to show that the bit assignment rule is useful for transforms of full pictures, but subjective bit assignments for transform picture coding using small block sizes are significantly different from the theoretical bit assignment rule. An intuitive explanation is based on subjective design experience, and a subjectively obtained bit assignment rule is given
Analytical and experimental investigations concerning the dual mode hydrazine system, task 4 Summary report, 1 Aug. 1967 - 1 Feb. 1968
Dual mode hydrazine system for attitude control and maneuvering propulsion of interplanetary space prob
A study of various synthetic routes to produce a halogen-labeled traction fluid
Several synthetic routes were studied for the synthesis of the compound 1, 1, 3-trimethyl-1, 3-dicyclohexyl-2 chloropropane. This halogen-labeled fluid would be of use in the study of high traction lubricants under elastohydrodynamic lubrication conditions using infrared emission spectroscopy. The synthetic routes included: dimerization of alpha-methylstyrene, methanol addition to alpha-methylstyrene, a Wittig reaction, and an organometallic approach. Because of steric hindrance and competing reactions, none of these routes were successful
Analysis of wear-debris from full-scale bearing fatigue tests using the ferrograph
The ferrograph was used to determine the types and quantities of wear particles generated during full-scale bearing fatigue tests. Deep-groove ball bearings made from AISI 52100 steel were used. A MIL-L-23699 tetraester lubricant was used in a recirculating lubrication system containing a 49 mm absolute filter. Test conditions included a maximum Hertz stress of 2.4 GPa, a shaft speed of 15,000 rpm, and a lubricant supply temperature of 74 C (165 F). Four fatigue failures were detected by accelerometers in this test set. In general, the ferrograph was more sensitive (up to 23 hr) in detecting spall initiation than either accelerometers or the normal spectrographic oil analysis. Four particle types were observed: normal rubbing wear particles, spheres, nonferrous particles, and severe wear (spall) fragments
Experimental apparatus for investigation of fan aeroelastic instabilities in turbomachinery
The application, installation, and monitoring of dynamic strain gage instrumentation on the rotating fan blades for subsonic stalled flutter mode of the first fan rotor are described. The engine installation, the modifications to the engine controls to obtain off schedule operation of the fan, engine aerodynamic instrumentation, and general data acquisition systems are discussed
- …